106673-7320 ZEXEL INJECTION-PUMP ASSEMBLY Calibration Data 1066737320


106673-7320 INJECTION-PUMP ASSEMBLY
Rating:
24
Buy INJECTION-PUMP ASSEMBLY 106673-7320 zexel genuine, new aftermarket engine parts with delivery

Information injection-pump assembly

ZEXEL 106673-7320 1066737320

Cross reference number

ZEXEL 106673-7320 1066737320


Zexel num
Bosch num
Firm num
Name
106673-7320 
 
   
INJECTION-PUMP ASSEMBLY

Calibration Data:

Adjustment conditions
Test oil
1404 Test oil
  ISO4113 or {SAEJ967d}
Test oil temperature degC   40 40 45
Nozzle and nozzle holder   105780-8250
Bosch type code   1 688 901 101
Nozzle   105780-0120
Bosch type code   1 688 901 990
Nozzle holder   105780-2190
Opening pressure MPa   20.7
Opening pressure kgf/cm2   211
Injection pipe
Outer diameter - inner diameter - length (mm)
mm   8-3-600
Overflow valve   131425-0220
Overflow valve opening pressure kPa   157 123 191
Overflow valve opening pressure kgf/cm2   1.6 1.25 1.95
Tester oil delivery pressure kPa   255 255 255
Tester oil delivery pressure kgf/cm2   2.6 2.6 2.6
Direction of rotation (viewed from drive side)
Right
  R
Injection timing adjustment
Direction of rotation (viewed from drive side)
Right
  R
Injection order   1-5-3-6- 2-4
Pre-stroke mm   3.9 3.85 3.95
Beginning of injection position
Governor side
  NO.1
Difference between angles 1
Cal 1-5
deg.   60 59.5 60.5
Difference between angles 2
Cal 1-3
deg.   120 119.5 120.5
Difference between angles 3
Cal 1-6
deg.   180 179.5 180.5
Difference between angles 4
Cyl.1-2
deg.   240 239.5 240.5
Difference between angles 5
Cal 1-4
deg.   300 299.5 300.5
Injection quantity adjustment
Adjusting point   -
Rack position   12.9
Pump speed r/min   700 700 700
Each cylinder's injection qty mm3/st.   147 143.3 150.7
Basic   *
Fixing the rack   *
Standard for adjustment of the maximum variation between cylinders   *
Injection quantity adjustment_02
Adjusting point   Z
Rack position   8+-0.5
Pump speed r/min   385 385 385
Each cylinder's injection qty mm3/st.   21 17.8 24.2
Fixing the rack   *
Standard for adjustment of the maximum variation between cylinders   *
Injection quantity adjustment_03
Adjusting point   A
Rack position   R1(12.9)
Pump speed r/min   700 700 700
Average injection quantity mm3/st.   147 146 148
Basic   *
Fixing the lever   *
Boost pressure kPa   23.3 23.3
Boost pressure mmHg   175 175
Injection quantity adjustment_04
Adjusting point   B
Rack position   R1+1.05
Pump speed r/min   1100 1100 1100
Average injection quantity mm3/st.   143.5 139.5 147.5
Fixing the lever   *
Boost pressure kPa   23.3 23.3
Boost pressure mmHg   175 175
Injection quantity adjustment_05
Adjusting point   C
Rack position   (R1-0.75 )
Pump speed r/min   500 500 500
Average injection quantity mm3/st.   142 136 148
Fixing the lever   *
Boost pressure kPa   23.3 23.3
Boost pressure mmHg   175 175
Injection quantity adjustment_06
Adjusting point   D
Rack position   (R2-1.3)
Pump speed r/min   300 300 300
Average injection quantity mm3/st.   104.5 102.5 106.5
Fixing the lever   *
Boost pressure kPa   0 0 0
Boost pressure mmHg   0 0 0
Boost compensator adjustment
Pump speed r/min   300 300 300
Rack position   (R2-1.3)
Boost pressure kPa   4 2.7 5.3
Boost pressure mmHg   30 20 40
Boost compensator adjustment_02
Pump speed r/min   300 300 300
Rack position   R2(R1-1)
Boost pressure kPa   10.7 10.7 10.7
Boost pressure mmHg   80 80 80

Test data Ex:

Governor adjustment

Test data 106673-7320
N:Pump speed R:Rack position (mm) (1)Torque cam stamping: T1 (2)Tolerance for racks not indicated: +-0.05mm. (3)Boost compensator stroke: BCL
----------
T1=AC25 BCL=(1.3)+-0.1mm
----------

Timer adjustment

Test data 106673-7320
(1)Adjusting range (2)Step response time (N): Speed of the pump (L): Load (theta) Advance angle (Srd1) Step response time 1 (Srd2) Step response time 2 1. Adjusting conditions for the variable timer (1)Adjust the clearance between the pickup and the protrusion to L.
----------
L=1-0.2mm N2=800r/min C2=(10)deg t1=2.5--sec. t2=2.5--sec.
----------
N1=750++r/min P1=0kPa(0kgf/cm2) P2=392kPa(4kgf/cm2) C1=10+-0.3deg R01=0/4load R02=4/4load

Speed control lever angle

Test data 106673-7320
F:Full speed I:Idle (1)Use the pin at R = aa (2)Stopper bolt set position 'H' (3)Viewed from feed pump side.
----------
aa=45mm
----------
a=30deg+-5deg b=(39deg)+-3deg

Stop lever angle

Test data 106673-7320
N:Pump normal S:Stop the pump. (1)At pump speed aa and rack position bb, set the stopper bolt. (Confirm non-injection.) (2)Normal engine position (Rack position corresponding to cc) (3)Use the hole above R = dd
----------
aa=1100r/min bb=3.5+-0.3mm cc=18mm dd=33.5mm
----------
a=40deg+-5deg b=25.5deg+-5deg c=(31deg)+-5deg

0000001501 MICRO SWITCH

Adjustment of the micro-switch Adjust the bolt to obtain the following lever position when the micro-switch is ON. (1)Speed N1 (2)Rack position Ra
----------
N1=325r/min Ra=7.6+-0.1mm
----------

0000001601 RACK SENSOR

Test data 106673-7320
(VR) measurement voltage (I) Part number of the control unit (G) Apply red paint. (H): End surface of the pump 1. Rack sensor adjustment (-0620) (1)Fix the speed control lever at the full position (2)Set the speed to N1 r/min. (If the boost compensator is provided, apply boost pressure.) (3)Adjust the bobbin (A) so that the rack sensor's output voltage is VR+-0.01. (4)At that time, rack position must be Ra. (5)Apply G at two places. Connecting part between the joint (B) and the nut (F) Connecting part between the joint (B) and the end surface of the pump (H)
----------
N1=1100r/min Ra=R1(12.9)+1.05mm
----------

0000001701 LEVER

Test data 106673-7320
Speed lever cancel adjustment procedure (without dashpot) (A) Top lever (B) Bottom lever (C) Return spring 1. At governor adjustment (FULL adjustment) (1)Set high idle using the lever (A). (2)Confirm that lever (A) is not cancelled with lever (B).
----------

----------

Timing setting

Test data 106673-7320
(1)Pump vertical direction (2)Coupling's key groove position at No 1 cylinder's beginning of injection (3)B.T.D.C.: aa (4)-
----------
aa=5deg
----------
a=(2deg)




Have questions with 106673-7320?





Group cross 106673-7320 ZEXEL

Mitsubishi 

9 400 617 336 
ME152000 
INJECTION-PUMP ASSEMBLY
6D22T2
9 400 617 337 
ME151986 
INJECTION-PUMP ASSEMBLY
6D24T1
106673-7320  
 
 
INJECTION-PUMP ASSEMBLY

Mitsubishi 

9 400 617 338 
ME151946 
INJECTION-PUMP ASSEMBLY
6D24T1
 
 
INJECTION-PUMP ASSEMBLY
 
 
INJECTION-PUMP ASSEMBLY

Mitsubishi 

9 400 610 929 
ME158180 
INJECTION-PUMP ASSEMBLY
6D22TC
 
 
INJECTION-PUMP ASSEMBLY

Mitsubishi 

9 400 617 339 
ME152019 
INJECTION-PUMP ASSEMBLY
6D24T1
 
 
INJECTION-PUMP ASSEMBLY

Mitsubishi 

9 400 611 838 
ME158173 
INJECTION-PUMP ASSEMBLY
6D24T
 
 
INJECTION-PUMP ASSEMBLY

Mitsubishi 

9 400 610 930 
ME158175 
INJECTION-PUMP ASSEMBLY
6D24T
9 400 610 931 
ME152100 
INJECTION-PUMP ASSEMBLY
6D22T2
 
 
INJECTION-PUMP ASSEMBLY
9 400 610 932 
 
INJECTION-PUMP ASSEMBLY

Mitsubishi 

9 400 617 340 
ME152089 
INJECTION-PUMP ASSEMBLY
6D24T1
9 400 619 456 
 
INJECTION-PUMP ASSEMBLY
9 400 619 457 
 
INJECTION-PUMP ASSEMBLY

Mitsubishi 

9 400 610 933 
ME158216 
INJECTION-PUMP ASSEMBLY
6D24TC
Back to top