106673-2901 ZEXEL 9 400 617 275 BOSCH INJECTION-PUMP ASSEMBLY 9400617275 1066732901 me157894


106673-2901 INJECTION-PUMP ASSEMBLY
Rating:
15
Buy INJECTION-PUMP ASSEMBLY 106673-2901 zexel genuine, new aftermarket engine parts with delivery

Information injection-pump assembly

BOSCH 9 400 617 275 9400617275
ZEXEL 106673-2901 1066732901
MITSUBISHI ME157894 me157894

Service parts 106673-2901 INJECTION-PUMP ASSEMBLY:

1. _
2. FUEL INJECTION PUMP 106061-7830
3. GOVERNOR 105408-0740
4. SUPPLY PUMP 105207-1210
5. AUTOM. ADVANCE MECHANIS 105636-1820
6. COUPLING PLATE 105662-0710
7. COUPLING PLATE
8. _
9. _
10. NOZZLE AND HOLDER ASSY 105100-6211
11. Nozzle and Holder ME059621
12. Open Pre:MPa(Kqf/cm2) 21.6{220}
13. NOZZLE-HOLDER 105030-5010
14. NOZZLE 105015-5330
15. NOZZLE SET

Include in #1:

106673-2901 as INJECTION-PUMP ASSEMBLY

Cross reference number

BOSCH 9 400 617 275 9400617275
ZEXEL 106673-2901 1066732901
MITSUBISHI ME157894 me157894


Zexel num
Bosch num
Firm num
Name
106673-2901 
9 400 617 275 
ME157894  MITSUBISHI
INJECTION-PUMP ASSEMBLY
6D22T K 14CA INJECTION PUMP ASSY PE6P,6PD PE

Calibration Data:

Adjustment conditions
Test oil
1404 Test oil
  ISO4113 or {SAEJ967d}
Test oil temperature degC   40 40 45
Nozzle and nozzle holder   105780-8140
Bosch type code   EF8511/9A
Nozzle   105780-0000
Bosch type code   DN12SD12T
Nozzle holder   105780-2080
Bosch type code   EF8511/9
Opening pressure MPa   17.2
Opening pressure kgf/cm2   175
Injection pipe
Outer diameter - inner diameter - length (mm)
mm   8-3-600
Overflow valve   131424-4620
Overflow valve opening pressure kPa   255 221 289
Overflow valve opening pressure kgf/cm2   2.6 2.25 2.95
Tester oil delivery pressure kPa   157 157 157
Tester oil delivery pressure kgf/cm2   1.6 1.6 1.6
Direction of rotation (viewed from drive side)
Right
  R
Injection timing adjustment
Direction of rotation (viewed from drive side)
Right
  R
Injection order   1-5-3-6- 2-4
Pre-stroke mm   4.8 4.75 4.85
Beginning of injection position
Governor side
  NO.1
Difference between angles 1
Cal 1-5
deg.   60 59.5 60.5
Difference between angles 2
Cal 1-3
deg.   120 119.5 120.5
Difference between angles 3
Cal 1-6
deg.   180 179.5 180.5
Difference between angles 4
Cyl.1-2
deg.   240 239.5 240.5
Difference between angles 5
Cal 1-4
deg.   300 299.5 300.5
Injection quantity adjustment
Adjusting point   A
Rack position   11.7
Pump speed r/min   1050 1050 1050
Average injection quantity mm3/st.   130 127 133
Max. variation between cylinders %   0 -3 3
Basic   *
Fixing the lever   *
Injection quantity adjustment_02
Adjusting point   -
Rack position   5.8+-0.5
Pump speed r/min   500 500 500
Average injection quantity mm3/st.   15 12.4 17.6
Max. variation between cylinders %   0 -15 15
Fixing the rack   *
Remarks
Adjust only variation between cylinders; adjust governor according to governor specifications.
 
Injection quantity adjustment_03
Adjusting point   C
Rack position   13.9+-0. 5
Pump speed r/min   100 100 100
Average injection quantity mm3/st.   133 113 153
Fixing the lever   *
Rack limit   *
Injection quantity adjustment_04
Adjusting point   D
Rack position   6
Pump speed r/min   260 260 260
Average injection quantity mm3/st.   10.6 5.4 15.8
Fixing the rack   *
Remarks
(check)
 
Timer adjustment
Pump speed r/min   950--
Advance angle deg.   0 0 0
Remarks
Start
 
Timer adjustment_02
Pump speed r/min   900
Advance angle deg.   0.5
Timer adjustment_03
Pump speed r/min   1100
Advance angle deg.   1 0.5 1.5
Remarks
Finish
 

Test data Ex:

Governor adjustment

Test data 106673-2901
N:Pump speed R:Rack position (mm) (1)Target notch: K (2)Tolerance for racks not indicated: +-0.05mm. (3)Torque spring does not operate. (4)RACK LIMIT (5)Main spring setting (6)Set idle sub-spring (7)Set at delivery
----------
K=8
----------

Speed control lever angle

Test data 106673-2901
F:Full speed I:Idle (1)Stopper bolt setting (2)At delivery (3)Pump speed = aa (4)Pump speed = bb
----------
aa=1110r/min bb=960r/min
----------
a=(29deg)+-5deg b=(2deg) c=(8deg)+-5deg d=(6deg)+-5deg

Stop lever angle

Test data 106673-2901
N:Pump normal S:Stop the pump.
----------

----------
a=36.5deg+-5deg b=53deg+-5deg

0000001501 RACK SENSOR

Test data 106673-2901
(VR) measurement voltage (I) Part number of the control unit (G) Apply red paint. (H): End surface of the pump 1. Rack sensor adjustment (-0620) (1)Fix the speed control lever at the full position (2)Set the speed to N1 r/min. (If the boost compensator is provided, apply boost pressure.) (3)Adjust the bobbin (A) so that the rack sensor's output voltage is VR+-0.01. (4)At that time, rack position must be Ra. (5)Apply G at two places. Connecting part between the joint (B) and the nut (F) Connecting part between the joint (B) and the end surface of the pump (H)
----------
N1=1050r/min Ra=11.7mm
----------

Timing setting

Test data 106673-2901
(1)Pump vertical direction (2)Coupling's key groove position at No 1 cylinder's beginning of injection (3)- (4)-
----------

----------
a=(7deg)




Have questions with 106673-2901?





Group cross 106673-2901 ZEXEL

 
 
INJECTION-PUMP ASSEMBLY

Mitsubishi 

106673-2901  
9 400 617 275 
ME157894 
INJECTION-PUMP ASSEMBLY
6D22T
 
 
INJECTION-PUMP ASSEMBLY
F 019 Z10 197 
 
INJECTION-PUMP ASSEMBLY

Mitsubishi 

9 400 617 276 
ME150861 
INJECTION-PUMP ASSEMBLY
6D22T3
9 400 617 277 
ME150815 
INJECTION-PUMP ASSEMBLY
E81XT1
9 400 617 278 
ME150814 
INJECTION-PUMP ASSEMBLY
E81XT1
F 01G 09U 08R 
 
INJECTION-PUMP ASSEMBLY

Mitsubishi 

9 400 617 279 
ME150925 
INJECTION-PUMP ASSEMBLY
E81XT1
 
 
INJECTION-PUMP ASSEMBLY

Mitsubishi 

9 400 617 280 
ME150926 
INJECTION-PUMP ASSEMBLY
E81XT2
9 400 617 281 
ME157908 
INJECTION-PUMP ASSEMBLY
6D22TC
 
 
INJECTION-PUMP ASSEMBLY

Mitsubishi 

9 400 617 282 
ME151216 
INJECTION-PUMP ASSEMBLY
6D22T6
 
 
INJECTION-PUMP ASSEMBLY
 
 
INJECTION-PUMP ASSEMBLY

Mitsubishi 

9 400 617 283 
ME151160 
INJECTION-PUMP ASSEMBLY
E81XT1
F 01G 09U 08S 
 
INJECTION-PUMP ASSEMBLY
F 01G 09U 08T 
 
INJECTION-PUMP ASSEMBLY
F 01G 09U 08U 
 
INJECTION-PUMP ASSEMBLY
9 400 619 773 
 
INJECTION-PUMP ASSEMBLY

Mitsubishi 

9 400 617 284 
ME151158 
INJECTION-PUMP ASSEMBLY
6D24T1
Back to top