106673-2991 ZEXEL F 01G 09U 08T BOSCH INJECTION-PUMP ASSEMBLY f01g09u08t 1066732991


106673-2991 INJECTION-PUMP ASSEMBLY
Rating:
32
Buy INJECTION-PUMP ASSEMBLY 106673-2991 zexel genuine, new aftermarket engine parts with delivery

Information injection-pump assembly

BOSCH F 01G 09U 08T f01g09u08t
ZEXEL 106673-2991 1066732991

Cross reference number

BOSCH F 01G 09U 08T f01g09u08t
ZEXEL 106673-2991 1066732991


Zexel num
Bosch num
Firm num
Name
106673-2991 
106673-2992 
F 01G 09U 08T 
   
INJECTION-PUMP ASSEMBLY
* K

Calibration Data:

Adjustment conditions
Test oil
1404 Test oil
  ISO4113 or {SAEJ967d}
Test oil temperature degC   40 40 45
Nozzle and nozzle holder   105780-8250
Bosch type code   1 688 901 101
Nozzle   105780-0120
Bosch type code   1 688 901 990
Nozzle holder   105780-2190
Opening pressure MPa   20.7
Opening pressure kgf/cm2   211
Injection pipe
Outer diameter - inner diameter - length (mm)
mm   8-3-600
Overflow valve   131425-0220
Overflow valve opening pressure kPa   157 123 191
Overflow valve opening pressure kgf/cm2   1.6 1.25 1.95
Tester oil delivery pressure kPa   255 255 255
Tester oil delivery pressure kgf/cm2   2.6 2.6 2.6
Direction of rotation (viewed from drive side)
Right
  R
Injection timing adjustment
Direction of rotation (viewed from drive side)
Right
  R
Injection order   1-5-3-6- 2-4
Pre-stroke mm   3.9 3.85 3.95
Beginning of injection position
Governor side
  NO.1
Difference between angles 1
Cal 1-5
deg.   60 59.5 60.5
Difference between angles 2
Cal 1-3
deg.   120 119.5 120.5
Difference between angles 3
Cal 1-6
deg.   180 179.5 180.5
Difference between angles 4
Cyl.1-2
deg.   240 239.5 240.5
Difference between angles 5
Cal 1-4
deg.   300 299.5 300.5
Injection quantity adjustment
Adjusting point   -
Rack position   12.9
Pump speed r/min   700 700 700
Each cylinder's injection qty mm3/st.   147 143.3 150.7
Basic   *
Fixing the rack   *
Standard for adjustment of the maximum variation between cylinders   *
Injection quantity adjustment_02
Adjusting point   Z
Rack position   8+-0.5
Pump speed r/min   390 390 390
Each cylinder's injection qty mm3/st.   15.8 13.4 18.2
Fixing the rack   *
Standard for adjustment of the maximum variation between cylinders   *
Injection quantity adjustment_03
Adjusting point   A
Rack position   R1(12.9)
Pump speed r/min   700 700 700
Average injection quantity mm3/st.   147 146 148
Basic   *
Fixing the lever   *
Boost pressure kPa   23.3 23.3
Boost pressure mmHg   175 175
Injection quantity adjustment_04
Adjusting point   B
Rack position   R1+1.05
Pump speed r/min   1100 1100 1100
Average injection quantity mm3/st.   143.5 139.5 147.5
Fixing the lever   *
Boost pressure kPa   23.3 23.3
Boost pressure mmHg   175 175
Injection quantity adjustment_05
Adjusting point   C
Rack position   (R1-0.75 )
Pump speed r/min   500 500 500
Average injection quantity mm3/st.   142 136 148
Fixing the lever   *
Boost pressure kPa   23.3 23.3
Boost pressure mmHg   175 175
Boost compensator adjustment
Pump speed r/min   300 300 300
Rack position   (R2-1.3)
Boost pressure kPa   4 2.7 5.3
Boost pressure mmHg   30 20 40
Boost compensator adjustment_02
Pump speed r/min   300 300 300
Rack position   R2(R1-1)
Boost pressure kPa   10.7 10.7 10.7
Boost pressure mmHg   80 80 80

Test data Ex:

Governor adjustment

Test data 106673-2991
N:Pump speed R:Rack position (mm) (1)Torque cam stamping: T1 (2)Tolerance for racks not indicated: +-0.05mm. (3)Boost compensator stroke: BCL (4)Damper spring setting
----------
T1=AC25 BCL=(1.3)+-0.1mm
----------

Timer adjustment

Test data 106673-2991
(1)Adjusting range (2)Step response time (N): Speed of the pump (L): Load (theta) Advance angle (Srd1) Step response time 1 (Srd2) Step response time 2 1. Adjusting conditions for the variable timer (1)Adjust the clearance between the pickup and the protrusion to L.
----------
L=1-0.2mm N2=800r/min C2=(10)deg t1=2.5--sec. t2=2.5--sec.
----------
N1=750++r/min P1=0kPa(0kgf/cm2) P2=392kPa(4kgf/cm2) C1=10+-0.3deg R01=0/4load R02=4/4load

Speed control lever angle

Test data 106673-2991
F:Full speed I:Idle (1)Use the hole at R = aa (2)Stopper bolt set position 'H' (3)Viewed from feed pump side.
----------
aa=37.5mm
----------
a=2deg+-5deg b=39.5deg+-3deg

Stop lever angle

Test data 106673-2991
N:Pump normal S:Stop the pump. (1)Use the hole at R = aa (2)Normal engine position (Rack position corresponding to bb) (3)Set the stopper bolt so that speed = cc and rack position = dd (and confirm non-injection).
----------
aa=54mm bb=18mm cc=1100r/min dd=3.5+-0.3mm
----------
a=(20.5deg) b=29.5deg+-5deg c=40deg+-5deg

0000001501 RACK SENSOR

Test data 106673-2991
(VR) measurement voltage (I) Part number of the control unit (G) Apply red paint. (H): End surface of the pump 1. Rack sensor adjustment (-0620) (1)Fix the speed control lever at the full position (2)Set the speed to N1 r/min. (If the boost compensator is provided, apply boost pressure.) (3)Adjust the bobbin (A) so that the rack sensor's output voltage is VR+-0.01. (4)At that time, rack position must be Ra. (5)Apply G at two places. Connecting part between the joint (B) and the nut (F) Connecting part between the joint (B) and the end surface of the pump (H)
----------
N1=1100r/min Ra=R1(12.9)+1.05mm
----------

0000001601 MICRO SWITCH

Adjustment of the micro-switch Adjust the bolt to obtain the following lever position when the micro-switch is ON. (1)Speed N1 (2)Rack position Ra
----------
N1=325r/min Ra=7.6+-0.1mm
----------

Timing setting

Test data 106673-2991
(1)Pump vertical direction (2)Coupling's key groove position at No 1 cylinder's beginning of injection (3)B.T.D.C.: aa (4)-
----------
aa=5deg
----------
a=(2deg)




Have questions with 106673-2991?





Group cross 106673-2991 ZEXEL

F 01G 09U 08S 
 
INJECTION-PUMP ASSEMBLY
106673-2991  

106673-2992 
F 01G 09U 08T 
 
INJECTION-PUMP ASSEMBLY
F 01G 09U 08U 
 
INJECTION-PUMP ASSEMBLY
9 400 619 773 
 
INJECTION-PUMP ASSEMBLY

Mitsubishi 

9 400 617 284 
ME151158 
INJECTION-PUMP ASSEMBLY
6D24T1
Back to top