106671-5401 ZEXEL 9 400 610 854 BOSCH INJECTION-PUMP ASSEMBLY 9400610854 1066715401 1680196661

Information Cross number Calibration Data Calibration Data Ex

Price: query
Buy now
Add to cart Go to cart

Rating:

Buy INJECTION-PUMP ASSEMBLY 106671-5401 zexel genuine, new aftermarket engine parts with delivery

Information injection-pump assembly

BOSCH 9 400 610 854 9400610854

ZEXEL 106671-5401 1066715401

NISSAN-DIESEL 1680196661 1680196661

Service parts 106671-5401 INJECTION-PUMP ASSEMBLY:

1. _

2. FUEL INJECTION PUMP 106067-0460

3. GOVERNOR 105952-1070

4. SUPPLY PUMP 105237-4210

5. AUTOM. ADVANCE MECHANIS 105683-0320

6. COUPLING PLATE 105663-0630

7. COUPLING PLATE

8. _

9. _

10. NOZZLE AND HOLDER ASSY 105160-4201

11. Nozzle and Holder 16600-96608

12. Open Pre:MPa(Kqf/cm2) 19.6{200}

13. NOZZLE-HOLDER 105030-4540

14. NOZZLE 105025-0391

15. NOZZLE SET

Include in #1:

106671-5401 as INJECTION-PUMP ASSEMBLY

Cross reference number

BOSCH 9 400 610 854 9400610854

ZEXEL 106671-5401 1066715401

NISSAN-DIESEL 1680196661 1680196661

Zexel num

Bosch num

Firm num

Name

106671-5401

9 400 610 854

1680196661 NISSAN-DIESEL

INJECTION-PUMP ASSEMBLY
D516X * K 14CA INJECTION PUMP ASSY PE6P,6PD PE

Calibration Data:

Adjustment conditions

Test oil
1404 Test oil ISO4113 or {SAEJ967d}

Test oil temperature degC 40 40 45

Nozzle and nozzle holder 105780-8250

Bosch type code 1 688 901 101

Nozzle 105780-0120

Bosch type code 1 688 901 990

Nozzle holder 105780-2190

Opening pressure MPa 20.7

Opening pressure kgf/cm2 211

Injection pipe
Outer diameter - inner diameter - length (mm) mm 8-3-600

Overflow valve 131425-0120

Overflow valve opening pressure kPa 157 123 191

Overflow valve opening pressure kgf/cm2 1.6 1.25 1.95

Tester oil delivery pressure kPa 255 255 255

Tester oil delivery pressure kgf/cm2 2.6 2.6 2.6

RED3 control unit part number 407910-3 960

RED3 rack sensor specifications mm 19

Direction of rotation (viewed from drive side)
Right R

Injection timing adjustment

Direction of rotation (viewed from drive side)
Right R

Injection order 1-4-2-6- 3-5

Pre-stroke mm 4.7 4.67 4.73

Beginning of injection position
Drive side NO.1

Difference between angles 1
Cal 1-4 deg. 60 59.75 60.25

Difference between angles 2
Cyl.1-2 deg. 120 119.75 120.25

Difference between angles 3
Cal 1-6 deg. 180 179.75 180.25

Difference between angles 4
Cal 1-3 deg. 240 239.75 240.25

Difference between angles 5
Cal 1-5 deg. 300 299.75 300.25

Injection quantity adjustment

Rack position (11.9)

Vist V 2.06 2.06 2.06

Pump speed r/min 650 650 650

Average injection quantity mm3/st. 109.5 108.5 110.5

Max. variation between cylinders % 0 -4 4

Basic *

Injection quantity adjustment_02

Rack position (8.7)

Vist V 2.5 2.4 2.6

Pump speed r/min 305 305 305

Average injection quantity mm3/st. 15 14 16

Max. variation between cylinders % 0 -10 10

Governor adjustment

Pump speed r/min 720--

Advance angle deg. 0 0 0

Remarks
Start

Governor adjustment_02

Pump speed r/min 670

Advance angle deg. 0.3

Governor adjustment_03

Pump speed r/min (720)

Advance angle deg. 1.5 1.2 1.8

Governor adjustment_04

Pump speed r/min -

Advance angle deg. 1.5 1.2 1.8

Remarks
Measure the actual speed.

Governor adjustment_05

Pump speed r/min 1050

Advance angle deg. 7 6.7 7.3

Remarks
Finish

Test data Ex:

Speed control lever angle

N:Pump normal S:Stop the pump. (1)Rack position = aa (2)Rack position bb
----------
aa=20mm bb=1mm
----------
a=20deg+-5deg b=37deg+-5deg

0000000901

(1)Pump vertical direction (2)Coupling's key groove position at No 1 cylinder's beginning of injection (3)- (4)-
----------

----------
a=(25deg)

Stop lever angle

(Rs) rack sensor specifications (C/U) control unit part number (V) Rack sensor output voltage (R) Rack position (mm) 1. Confirming governor output characteristics (rack 19 mm, span 6 mm) (1)When the output voltages of the rack sensor are V1 and V2, check that the rack positions R1 and R2 in the table above are satisfied.
----------

----------