106661-0690 ZEXEL INJECTION-PUMP ASSEMBLY Calibration Data 1066610690 1671396514


106661-0690 INJECTION-PUMP ASSEMBLY
Rating:
29
Buy INJECTION-PUMP ASSEMBLY 106661-0690 zexel genuine, new aftermarket engine parts with delivery

Information injection-pump assembly

ZEXEL 106661-0690 1066610690
NISSAN-DIESEL 1671396514 1671396514

Service parts 106661-0690 INJECTION-PUMP ASSEMBLY:

1. _
2. FUEL INJECTION PUMP 106066-1160
3. GOVERNOR 105487-0310
4. SUPPLY PUMP 105217-4000
5. AUTOM. ADVANCE MECHANIS 105614-0660
6. COUPLING PLATE 105662-0370
7. COUPLING PLATE
8. _
9. _
10. NOZZLE AND HOLDER ASSY 105100-4050
11. Nozzle and Holder 16600-96001
12. Open Pre:MPa(Kqf/cm2) 19.6{200}
13. NOZZLE-HOLDER 105031-4270
14. NOZZLE 105015-2780
15. NOZZLE SET

Include in #1:

106661-0690 as INJECTION-PUMP ASSEMBLY

Cross reference number

ZEXEL 106661-0690 1066610690
NISSAN-DIESEL 1671396514 1671396514


Zexel num
Bosch num
Firm num
Name
106661-0690 
106661-0692 
 
1671396514  NISSAN-DIESEL
INJECTION-PUMP ASSEMBLY
PE6 *

Calibration Data:

Adjustment conditions
Test oil
1404 Test oil
  ISO4113 or {SAEJ967d}
Test oil temperature degC   40 40 45
Nozzle and nozzle holder   105780-8140
Bosch type code   EF8511/9A
Nozzle   105780-0000
Bosch type code   DN12SD12T
Nozzle holder   105780-2080
Bosch type code   EF8511/9
Opening pressure MPa   17.2
Opening pressure kgf/cm2   175
Injection pipe
Outer diameter - inner diameter - length (mm)
mm   8-3-600
Tester oil delivery pressure kPa   157 157 157
Tester oil delivery pressure kgf/cm2   1.6 1.6 1.6
Direction of rotation (viewed from drive side)
Right
  R
Injection timing adjustment
Direction of rotation (viewed from drive side)
Right
  R
Injection order   1-4-2-6- 3-5
Pre-stroke mm   3.65 3.6 3.7
Beginning of injection position
Drive side
  NO.1
Difference between angles 1
Cal 1-4
deg.   60 59.5 60.5
Difference between angles 2
Cyl.1-2
deg.   120 119.5 120.5
Difference between angles 3
Cal 1-6
deg.   180 179.5 180.5
Difference between angles 4
Cal 1-3
deg.   240 239.5 240.5
Difference between angles 5
Cal 1-5
deg.   300 299.5 300.5
Injection quantity adjustment
Adjusting point   A
Rack position   10.4
Pump speed r/min   1150 1150 1150
Average injection quantity mm3/st.   134 131 137
Max. variation between cylinders %   0 -4 4
Fixing the lever   *
Injection quantity adjustment_02
Adjusting point   B
Rack position   10.4
Pump speed r/min   1000 1000 1000
Average injection quantity mm3/st.   131.6 128.6 134.6
Max. variation between cylinders %   0 -4 4
Fixing the lever   *
Injection quantity adjustment_03
Adjusting point   C
Rack position   10.4
Pump speed r/min   750 750 750
Average injection quantity mm3/st.   130.8 128.8 132.8
Max. variation between cylinders %   0 -4 4
Basic   *
Fixing the lever   *
Rack limit   *
Injection quantity adjustment_04
Adjusting point   D
Rack position   6.4+-0.5
Pump speed r/min   200 200 200
Average injection quantity mm3/st.   9 8.1 9.9
Max. variation between cylinders %   0 -10 10
Fixing the rack   *
Timer adjustment
Pump speed r/min   300+-50
Advance angle deg.   0 0 0
Remarks
Start
 
Timer adjustment_02
Pump speed r/min   500
Advance angle deg.   0.95 0.6 1.3
Timer adjustment_03
Pump speed r/min   700
Advance angle deg.   1.75 1.4 2.1
Timer adjustment_04
Pump speed r/min   900
Advance angle deg.   2.75 2.4 3.1
Timer adjustment_05
Pump speed r/min   1100+50
Advance angle deg.   4 3.4 4.2
Remarks
Finish
 

Test data Ex:

Governor adjustment

Test data 106661-0690
N:Pump speed R:Rack position (mm) (1)Adjust with speed control lever at full position (minimum-maximum speed specification) (2)Adjust with the load control lever in the full position (variable speed specification). (3)Rack limit using stop lever (4)Damper spring setting: DL (5)Idle sub spring setting: L1.
----------
DL=3.2-0.2mm L1=3.9-0.2mm
----------

Speed control lever angle

Test data 106661-0690
F:Full speed I:Idle
----------

----------
a=10deg+-5deg b=10deg+-5deg

0000000901

Test data 106661-0690
F:Full load I:Idle
----------

----------
a=14deg+-5deg b=36deg+-3deg

Stop lever angle

Test data 106661-0690
N:Pump normal S:Stop the pump. (1)Use the hole at R = aa (2)Rack position bb (3)Stopper bolt setting
----------
aa=50mm bb=10mm
----------
a=24deg+-5deg b=27deg+-3deg




Have questions with 106661-0690?





Group cross 106661-0690 ZEXEL

Nissan-Diesel 

 
 
INJECTION-PUMP ASSEMBLY
PD6T
 
1679096002 
INJECTION-PUMP ASSEMBLY
PD6T
 
1670096106 

PD6HT
 
1671796501 
INJECTION-PUMP ASSEMBLY
PE60
 
 
INJECTION-PUMP ASSEMBLY
PE60
 
 
INJECTION-PUMP ASSEMBLY

Nissan-Diesel 

 
1671796502 
INJECTION-PUMP ASSEMBLY
PE60
 
 
INJECTION-PUMP ASSEMBLY
PD6T
 
 
INJECTION-PUMP ASSEMBLY

Nissan-Diesel 

 
1671796007 
INJECTION-PUMP ASSEMBLY
PD6T
 
 
INJECTION-PUMP ASSEMBLY
PD6T
 
1679096003 
INJECTION-PUMP ASSEMBLY
PD6T
 
1670096108 
INJECTION-PUMP ASSEMBLY
PD6T
 
 
INJECTION-PUMP ASSEMBLY
PD6T
 
 
INJECTION-PUMP ASSEMBLY

Nissan-Diesel 

9 400 616 578 
1670096065 
INJECTION-PUMP ASSEMBLY
PD6T
 
1670096109 
INJECTION-PUMP ASSEMBLY
PD6T
 
 
INJECTION-PUMP ASSEMBLY
PD6T
 
 
INJECTION-PUMP ASSEMBLY

Nissan-Diesel 

 
1670096066 
INJECTION-PUMP ASSEMBLY
PD6T
 
1671396104 
INJECTION-PUMP ASSEMBLY
PD6T
 
 
INJECTION-PUMP ASSEMBLY
PD6T
 
 
INJECTION-PUMP ASSEMBLY

Nissan-Diesel 

9 400 616 579 
1671396065 
INJECTION-PUMP ASSEMBLY
PD6T
106661-0690  

106661-0692 
 
1671396514 
INJECTION-PUMP ASSEMBLY
PE6
 
 
INJECTION-PUMP ASSEMBLY

Nissan-Diesel 

 
1671396577 
INJECTION-PUMP ASSEMBLY
PE6
Back to top