101609-3710 ZEXEL INJECTION-PUMP ASSEMBLY Calibration Data 1016093710

Information Cross number Calibration Data Calibration Data Ex

Price: query
Buy now
Add to cart Go to cart

Rating:

Buy INJECTION-PUMP ASSEMBLY 101609-3710 zexel genuine, new aftermarket engine parts with delivery

Information injection-pump assembly

ZEXEL 101609-3710 1016093710

Service parts 101609-3710 INJECTION-PUMP ASSEMBLY:

1. _

2. FUEL INJECTION PUMP 101062-9340

3. GOVERNOR 105404-6000

4. SUPPLY PUMP

105220-5960

5. AUTOM. ADVANCE MECHANIS

6. COUPLING PLATE

7. COUPLING PLATE

8. _

9. _

10. NOZZLE AND HOLDER ASSY 105158-5002

11. Nozzle and Holder 4063212

12. Open Pre:MPa(Kqf/cm2) 22.0{224}

13. NOZZLE-HOLDER 105088-2002

14. NOZZLE

105017-2910

15. NOZZLE SET

Include in #1:

101609-3710 as INJECTION-PUMP ASSEMBLY

Include in #2:

104265-4052 as _

Cross reference number

ZEXEL 101609-3710 1016093710

Zexel num

Bosch num

Firm num

Name

101609-3710

INJECTION-PUMP ASSEMBLY
14BE PE6A PE

Calibration Data:

Adjustment conditions

Test oil
1404 Test oil ISO4113 or {SAEJ967d}

Test oil temperature degC 40 40 45

Nozzle and nozzle holder 105780-8140

Bosch type code EF8511/9A

Nozzle 105780-0000

Bosch type code DN12SD12T

Nozzle holder 105780-2080

Bosch type code EF8511/9

Opening pressure MPa 17.2

Opening pressure kgf/cm2 175

Injection pipe
Outer diameter - inner diameter - length (mm) mm 6-2-600

Overflow valve 131424-3420

Overflow valve opening pressure kPa 255 221 289

Overflow valve opening pressure kgf/cm2 2.6 2.25 2.95

Tester oil delivery pressure kPa 255 255 255

Tester oil delivery pressure kgf/cm2 2.6 2.6 2.6

Direction of rotation (viewed from drive side)
Right R

Injection timing adjustment

Direction of rotation (viewed from drive side)
Right R

Injection order 1-5-3-6- 2-4

Pre-stroke mm 2.6 2.55 2.65

Rack position
After adjusting injection quantity. R=A

Beginning of injection position
Drive side NO.1

Difference between angles 1
Cal 1-5 deg. 60 59.5 60.5

Difference between angles 2
Cal 1-3 deg. 120 119.5 120.5

Difference between angles 3
Cal 1-6 deg. 180 179.5 180.5

Difference between angles 4
Cyl.1-2 deg. 240 239.5 240.5

Difference between angles 5
Cal 1-4 deg. 300 299.5 300.5

Injection quantity adjustment

Adjusting point A

Rack position 11.3

Pump speed r/min 1000 1000 1000

Average injection quantity mm3/st. 124 123 125

Max. variation between cylinders % 0 -2.5 2.5

Basic *

Fixing the lever *

Boost pressure kPa 70 70

Boost pressure mmHg 525 525

Injection quantity adjustment_02

Adjusting point -

Rack position 7.9+-0.5

Pump speed r/min 410 410 410

Average injection quantity mm3/st. 9.5 8.5 10.5

Max. variation between cylinders % 0 -15 15

Fixing the rack *

Boost pressure kPa 0 0 0

Boost pressure mmHg 0 0 0

Remarks
Adjust only variation between cylinders; adjust governor according to governor specifications.

Injection quantity adjustment_03

Adjusting point E

Rack position 11.5++

Pump speed r/min 100 100 100

Average injection quantity mm3/st. 120 115 125

Fixing the lever *

Boost pressure kPa 70 70

Boost pressure mmHg 525 525

Rack limit *

Injection quantity adjustment_04

Adjusting point F

Rack position R1(11.3)

Pump speed r/min 800 800 800

Average injection quantity mm3/st. 123 113 133

Fixing the lever *

Boost pressure kPa 70 70

Boost pressure mmHg 525 525

Boost compensator adjustment

Pump speed r/min 800 800 800

Rack position R1-1.8

Boost pressure kPa 17.3 17.3 17.3

Boost pressure mmHg 130 130 130

Boost compensator adjustment_02

Pump speed r/min 800 800 800

Rack position R1-1.1

Boost pressure kPa 30.7 29.4 32

Boost pressure mmHg 230 220 240

Boost compensator adjustment_03

Pump speed r/min 800 800 800

Rack position R1(11.3)

Boost pressure kPa 56.7 56.7 56.7

Boost pressure mmHg 425 425 425

Test data Ex:

Governor adjustment

N:Pump speed R:Rack position (mm) (1)Target notch: K (2)Tolerance for racks not indicated: +-0.05mm. (3)It is not necessary to supply hydraulic pressure because the specification is for the hydraulic ACT normally ON. (4)RACK LIMIT (5)Boost compensator stroke: BCL (6)Rack difference between N = N1 and N = N2
----------
K=16 BCL=1.8+-0.1mm N1=1000r/min N2=450r/min
----------

Speed control lever angle

F:Full speed I:Idle (1)Stopper bolt setting
----------

----------
a=13deg+-5deg b=35deg+-5deg

Stop lever angle

N:Pump normal S:Stop the pump. (1)No return spring
----------

----------
a=0deg+-5deg b=53deg+-5deg

0000001501 TAMPER PROOF

Tamperproofing-equipped boost compensator cover installation procedure (1)After adjusting the governor and the boost compensator, tighten to the specified torque to break off the bolt heads. (Tightening torque T = T1 maximum) (2)After adjusting the governor and the boost compensator, tighten to the specified torque to break off the bolt heads. (Tightening torque T = T2) (3)After adjusting the governor and the boost compensator, tighten to the specified torque to break off the bolt heads. (Tightening torque T = T3)
----------
T1=7.16~9.12N-m(0.73~0.93kgf-m) T2=2.9~4.4N-m(0.3~0.45kgf-m) T3=2.9~4.4N-m(0.3~0.45kgf-m)
----------

0000001601 I/P WITH LOAD PLUNGER ADJ

Adjusting procedure for load plunger equipped pump with RSV (cam lock) governor (see service information S.I. 434 for details). At cam lift h+-0.01, set the camshaft c deg from the * mark in accordance with the timing adjustment procedure. 2. Align the flyweight's timing tooth position and the lock pin groove and then fully tighten the flyweight to the camshaft. Then, remove the lock pin. 3. Adjust the maximum variation between cylinders and injection quantity. 4. Adjust using the pre-stroke adjusting shim so that the pre-stroke value is the value for 4/4 load (standard point A). 5. After adjusting the pre-stroke, reconfirm that the injection quantity and the maximum variation between cylinders are as specified. 6. At delivery, again fix the flyweight using the lock pin.
----------
h=2.6+-0.01mm c=5deg15min+-30min
----------

Timing setting

(1)Pump vertical direction (2)Key groove position for No. 1 cylinder's cam lift h = cc (at BTDC aa). (3)Key groove position for No. 1 cylinder's beginning of injection (at point A after injection quantity adjustment). (4)Position of the key groove of the No. 1 cylinder at B.T.D.C. bb (fix the governor flyweight at this position for delivery). (5)B.T.D.C.: aa
----------
aa=10.5deg bb=0deg cc=2.6+-0.01mm
----------
a=55deg18min+-3deg b=55deg18min+-3deg13min48sec c=5deg15min+-30min