101608-6250 ZEXEL INJECTION-PUMP ASSEMBLY Calibration Data 1016086250

Information Cross number Calibration Data Calibration Data Ex

Price: query
Buy now
Add to cart Go to cart

Rating:

Buy INJECTION-PUMP ASSEMBLY 101608-6250 zexel genuine, new aftermarket engine parts with delivery

Information injection-pump assembly

ZEXEL 101608-6250 1016086250

Cross reference number

ZEXEL 101608-6250 1016086250

Zexel num

Bosch num

Firm num

Name

101608-6250

INJECTION-PUMP ASSEMBLY
6D34TL

Calibration Data:

Adjustment conditions

Test oil
1404 Test oil ISO4113 or {SAEJ967d}

Test oil temperature degC 40 40 45

Nozzle and nozzle holder 105780-8140

Bosch type code EF8511/9A

Nozzle 105780-0000

Bosch type code DN12SD12T

Nozzle holder 105780-2080

Bosch type code EF8511/9

Opening pressure MPa 17.2

Opening pressure kgf/cm2 175

Injection pipe
Outer diameter - inner diameter - length (mm) mm 6-2-600

Overflow valve 131424-5520

Overflow valve opening pressure kPa 255 221 289

Overflow valve opening pressure kgf/cm2 2.6 2.25 2.95

Tester oil delivery pressure kPa 255 255 255

Tester oil delivery pressure kgf/cm2 2.6 2.6 2.6

Direction of rotation (viewed from drive side)
Right R

Injection timing adjustment

Direction of rotation (viewed from drive side)
Right R

Injection order 1-5-3-6- 2-4

Pre-stroke mm 3.5 3.45 3.55

Beginning of injection position
Drive side NO.1

Difference between angles 1
Cal 1-5 deg. 60 59.5 60.5

Difference between angles 2
Cal 1-3 deg. 120 119.5 120.5

Difference between angles 3
Cal 1-6 deg. 180 179.5 180.5

Difference between angles 4
Cyl.1-2 deg. 240 239.5 240.5

Difference between angles 5
Cal 1-4 deg. 300 299.5 300.5

Injection quantity adjustment

Adjusting point A

Rack position 8.4

Pump speed r/min 1100 1100 1100

Average injection quantity mm3/st. 97.5 96.5 98.5

Max. variation between cylinders % 0 -2.5 2.5

Basic *

Fixing the lever *

Boost pressure kPa 89.3 89.3

Boost pressure mmHg 670 670

Injection quantity adjustment_02

Adjusting point -

Rack position 5.8+-0.5

Pump speed r/min 475 475 475

Average injection quantity mm3/st. 8 6.7 9.3

Max. variation between cylinders % 0 -14 14

Fixing the rack *

Boost pressure kPa 0 0 0

Boost pressure mmHg 0 0 0

Remarks
Adjust only variation between cylinders; adjust governor according to governor specifications.

Injection quantity adjustment_03

Adjusting point E

Rack position -

Pump speed r/min 100 100 100

Average injection quantity mm3/st. 70 70 75

Fixing the lever *

Boost pressure kPa 0 0 0

Boost pressure mmHg 0 0 0

Rack limit *

Boost compensator adjustment

Pump speed r/min 750 750 750

Rack position R1-0.65

Boost pressure kPa 37.3 32 42.6

Boost pressure mmHg 280 240 320

Boost compensator adjustment_02

Pump speed r/min 750 750 750

Rack position R1(8.4)

Boost pressure kPa 76 76 76

Boost pressure mmHg 570 570 570

Timer adjustment

Pump speed r/min 0

Advance angle deg. 2 1.5 2.5

Timer adjustment_02

Pump speed r/min -

Advance angle deg. 2 1.5 2.5

Remarks
Measure speed (beginning of operation).

Timer adjustment_03

Pump speed r/min 750+-25

Advance angle deg. 0 0 0

Remarks
Finish

Test data Ex:

Governor adjustment

N:Pump speed R:Rack position (mm) (1)Target notch: K (2)Tolerance for racks not indicated: +-0.05mm. (3)RACK LIMIT (4)Set idle sub-spring (5)Main spring setting (6)Boost compensator stroke: BCL
----------
K=15 BCL=0.65+-0.1mm
----------

Speed control lever angle

F:Full speed I:Idle (1)Stopper bolt setting
----------

----------
a=14deg+-5deg b=21deg+-5deg

Stop lever angle

N:Pump normal S:Stop the pump. (1)Pump speed aa and rack position bb (to be sealed at delivery) (2)Normal
----------
aa=0r/min bb=1-0.5mm
----------
a=21deg+-5deg b=(55deg)

0000001501 TAMPER PROOF

Tamperproofing-equipped boost compensator cover installation procedure (A) After adjusting the boost compensator, tighten the bolts to remove the heads. (1)Before adjusting the governor and the boost compensator, tighten the screw to the specified torque. (Tightening torque T = T1 maximum) (2)After adjusting the governor and the boost compensator, tighten to the specified torque to break off the bolt heads. (Tightening torque T = T2)
----------
T1=2.5N-m(0.25kgf-m) T2=2.9~4.4N-m(0.3~0.45kgf-m)
----------

Timing setting

(1)Pump vertical direction (2)Position of gear mark '3' at No 1 cylinder's beginning of injection (3)B.T.D.C.: aa (4)-
----------
aa=14deg
----------
a=(130deg)