101601-8171 ZEXEL INJECTION-PUMP ASSEMBLY Calibration Data 1016018171 1156014281


101601-8171 INJECTION-PUMP ASSEMBLY
Rating:
79
Buy INJECTION-PUMP ASSEMBLY 101601-8171 zexel genuine, new aftermarket engine parts with delivery

Information injection-pump assembly

ZEXEL 101601-8171 1016018171
ISUZU 1156014281 1156014281

Cross reference number

ZEXEL 101601-8171 1016018171
ISUZU 1156014281 1156014281


Zexel num
Bosch num
Firm num
Name
101601-8171 
101601-8172 
 
1156014281  ISUZU
INJECTION-PUMP ASSEMBLY
6QA1 *

Calibration Data:

Adjustment conditions
Test oil
1404 Test oil
  ISO4113 or {SAEJ967d}
Test oil temperature degC   40 40 45
Nozzle and nozzle holder   105780-8140
Bosch type code   EF8511/9A
Nozzle   105780-0000
Bosch type code   DN12SD12T
Nozzle holder   105780-2080
Bosch type code   EF8511/9
Opening pressure MPa   17.2
Opening pressure kgf/cm2   175
Injection pipe
Outer diameter - inner diameter - length (mm)
mm   6-2-600
Overflow valve   131424-0220
Overflow valve opening pressure kPa   147 113 181
Overflow valve opening pressure kgf/cm2   1.5 1.15 1.85
Tester oil delivery pressure kPa   157 157 157
Tester oil delivery pressure kgf/cm2   1.6 1.6 1.6
Direction of rotation (viewed from drive side)
Right
  R
Injection timing adjustment
Direction of rotation (viewed from drive side)
Right
  R
Injection order   1-4-2-6- 3-5
Pre-stroke mm   3.7 3.65 3.75
Beginning of injection position
Drive side
  NO.1
Difference between angles 1
Cal 1-4
deg.   60 59.5 60.5
Difference between angles 2
Cyl.1-2
deg.   120 119.5 120.5
Difference between angles 3
Cal 1-6
deg.   180 179.5 180.5
Difference between angles 4
Cal 1-3
deg.   240 239.5 240.5
Difference between angles 5
Cal 1-5
deg.   300 299.5 300.5
Injection quantity adjustment
Adjusting point   A
Rack position   10.9
Pump speed r/min   1150 1150 1150
Average injection quantity mm3/st.   106.2 104.2 108.2
Max. variation between cylinders %   0 -4 4
Fixing the lever   *
Injection quantity adjustment_02
Adjusting point   B
Rack position   11.2
Pump speed r/min   700 700 700
Average injection quantity mm3/st.   108.1 107.1 109.1
Max. variation between cylinders %   0 -2 2
Basic   *
Fixing the lever   *
Injection quantity adjustment_03
Adjusting point   C
Rack position   8.6+-0.5
Pump speed r/min   225 225 225
Average injection quantity mm3/st.   11.5 9.2 13.8
Max. variation between cylinders %   0 -13 13
Fixing the rack   *
Injection quantity adjustment_04
Adjusting point   D
Rack position   -
Pump speed r/min   150 150 150
Each cylinder's injection qty mm3/st.   140 140
Fixing the lever   *
Remarks
After startup boost setting
 
Injection quantity adjustment_05
Adjusting point   E
Rack position   9.8
Pump speed r/min   700 700 700
Average injection quantity mm3/st.   73 71 75
Max. variation between cylinders %   0 -2 2
Fixing the lever   *
Remarks
At absolute pressure 61.3 kPa {460 mmHg}
 
Timer adjustment
Pump speed r/min   500
Advance angle deg.   0.3
Timer adjustment_02
Pump speed r/min   600
Advance angle deg.   0.8 0.1 0.8
Timer adjustment_03
Pump speed r/min   700
Advance angle deg.   0.8 0.3 1.3
Timer adjustment_04
Pump speed r/min   900
Advance angle deg.   2 1.5 2.5
Timer adjustment_05
Pump speed r/min   1150
Advance angle deg.   4 3.5 4.5
Remarks
Finish
 

Test data Ex:

Governor adjustment

Test data 101601-8171
N:Pump speed R:Rack position (mm) (1)Excess fuel setting for starting: SXL (2)Beginning of damper spring operation: DL (3)Aneroid compensator absolute pressure: P1
----------
SXL=12.1+-0.1mm DL=6.5+-0.5mm P1=61.3+-0.7kPa(460+-5mmHg)
----------

Speed control lever angle

Test data 101601-8171
F:Full speed
----------

----------
a=3deg+-5deg

0000000901

Test data 101601-8171
F:Full load I:Idle (1)Attach the return spring to the upper hole and adjust. (2)Stopper bolt setting
----------

----------
a=21deg+-3deg b=30deg+-5deg

Stop lever angle

Test data 101601-8171
N:Pump normal S:Stop the pump.
----------

----------
a=65.5deg+-5deg b=71deg+-5deg

0000001501 ACS

Test data 101601-8171
(A) Set screw (B) Push rod 1 1. Aneroid compensator unit adjustment (1)Screw in (A) to obtain L1. 2. Adjustment following governor installation (1)Set the speed of the pump to N1 r/min and fix the control lever at the full set position. (2)Screw in the aneroid compensator to obtain the performance shown in the graph above.
----------
N1=700r/min L1=(0.6~0.9)mm
----------
R1=11.2mm R2=9.8mm P1=(90.6)kPa((680)mmHg) P2=61.3+-0.7kPa(460+-5mmHg) Q1=108.1+-1cm3/1000st Q2=(73)+-1cm3/1000st




Have questions with 101601-8171?





Group cross 101601-8171 ZEXEL

Isuzu 

 
1156013800 
INJECTION-PUMP ASSEMBLY
6BD1T
 
1156013803 
INJECTION-PUMP ASSEMBLY
6BD1T
9 400 619 718 
1156014172 
INJECTION-PUMP ASSEMBLY
6QA1
 
1156013401 
INJECTION-PUMP ASSEMBLY
6BD1T
 
1156013403 
INJECTION-PUMP ASSEMBLY
6BD1-T
 
1156013404 
INJECTION-PUMP ASSEMBLY
6BD1-T
 
1156013406 
INJECTION-PUMP ASSEMBLY
6BD1-T
 
1156013407 
INJECTION-PUMP ASSEMBLY
6BD1-T
 
1156013408 
INJECTION-PUMP ASSEMBLY
6BD1T
 
1156013380 
INJECTION-PUMP ASSEMBLY
6BG1
 
1156013381 
INJECTION-PUMP ASSEMBLY
6BG1
 
1156013382 
INJECTION-PUMP ASSEMBLY
6BG1
 
1156013384 
INJECTION-PUMP ASSEMBLY
6BG1
 
1156013385 
INJECTION-PUMP ASSEMBLY
6BG1
 
1156013390 
INJECTION-PUMP ASSEMBLY
6BG1
 
 
INJECTION-PUMP ASSEMBLY
6BG1
 
1156013391 
INJECTION-PUMP ASSEMBLY
6BG1
 
1156013393 
INJECTION-PUMP ASSEMBLY
6BG1
 
1156013394 
INJECTION-PUMP ASSEMBLY
6BG1
 
1156014230 
INJECTION-PUMP ASSEMBLY
6QA1
 
1156014231 
INJECTION-PUMP ASSEMBLY
6QA1
9 400 619 755 
1156014233 
INJECTION-PUMP ASSEMBLY
6QA1
 
1156014240 
INJECTION-PUMP ASSEMBLY
6QA1
 
1156014280 
INJECTION-PUMP ASSEMBLY
6QA1
101601-8171  

101601-8172 
 
1156014281 
INJECTION-PUMP ASSEMBLY
6QA1
9 400 619 841 
1156014283 
INJECTION-PUMP ASSEMBLY
6QA1
 
1156014330 
INJECTION-PUMP ASSEMBLY
6QA1
 
1156015611 
INJECTION-PUMP ASSEMBLY
6QA1
Back to top