106861-0811 ZEXEL INJECTION-PUMP ASSEMBLY Calibration Data 1068610811

Information Cross number Calibration Data Calibration Data Ex

Price: query
Buy now
Add to cart Go to cart

Rating:

Buy INJECTION-PUMP ASSEMBLY 106861-0811 zexel genuine, new aftermarket engine parts with delivery

Information injection-pump assembly

ZEXEL 106861-0811 1068610811

Service parts 106861-0811 INJECTION-PUMP ASSEMBLY:

1. _

2. FUEL INJECTION PUMP 106086-5411

3. GOVERNOR 105487-0851

4. SUPPLY PUMP 105217-1720

5. AUTOM. ADVANCE MECHANIS 105636-0280

6. COUPLING PLATE 105662-0602

7. COUPLING PLATE

8. _

9. _

10. NOZZLE AND HOLDER ASSY 105100-4880

11. Nozzle and Holder 1660097015

12. Open Pre:MPa(Kqf/cm2) 19.6(200)

13. NOZZLE-HOLDER 105031-4210

14. NOZZLE

105015-4530

15. NOZZLE SET

Include in #1:

106861-0811 as INJECTION-PUMP ASSEMBLY

Cross reference number

ZEXEL 106861-0811 1068610811

Zexel num

Bosch num

Firm num

Name

106861-0811

INJECTION-PUMP ASSEMBLY

Calibration Data:

Adjustment conditions

Test oil
1404 Test oil ISO4113 or {SAEJ967d}

Test oil temperature degC 40 40 45

Nozzle and nozzle holder 105780-8140

Bosch type code EF8511/9A

Nozzle 105780-0000

Bosch type code DN12SD12T

Nozzle holder 105780-2080

Bosch type code EF8511/9

Opening pressure MPa 17.2

Opening pressure kgf/cm2 175

Injection pipe
Outer diameter - inner diameter - length (mm) mm 8-3-600

Overflow valve 132424-0620

Overflow valve opening pressure kPa 157 123 191

Overflow valve opening pressure kgf/cm2 1.6 1.25 1.95

Tester oil delivery pressure kPa 157 157 157

Tester oil delivery pressure kgf/cm2 1.6 1.6 1.6

Direction of rotation (viewed from drive side)
Right R

Injection timing adjustment

Direction of rotation (viewed from drive side)
Right R

Injection order 1-8-7-5- 4-3-6-2

Pre-stroke mm 3.65 3.6 3.7

Beginning of injection position
Governor side NO.1

Difference between angles 1
Cal 1-8 deg. 45 44.5 45.5

Difference between angles 2
Cal 1-7 deg. 90 89.5 90.5

Difference between angles 3
Cal 1-5 deg. 135 134.5 135.5

Difference between angles 4
Cal 1-4 deg. 180 179.5 180.5

Difference between angles 5
Cal 1-3 deg. 225 224.5 225.5

Difference between angles 6
Cal 1-6 deg. 270 269.5 270.5

Difference between angles 7
Cyl.1-2 deg. 315 314.5 315.5

Injection quantity adjustment

Adjusting point A

Rack position 11.6

Pump speed r/min 700 700 700

Average injection quantity mm3/st. 105.1 104.1 106.1

Max. variation between cylinders % 0 -4 4

Basic *

Fixing the lever *

Injection quantity adjustment_02

Adjusting point B

Rack position 6.9+-0.5

Pump speed r/min 250 250 250

Average injection quantity mm3/st. 13.1 11.1 15.1

Max. variation between cylinders % 0 -10 10

Fixing the rack *

Timer adjustment

Pump speed r/min 650--

Advance angle deg. 0 0 0

Remarks
Start

Timer adjustment_02

Pump speed r/min 600

Advance angle deg. 0.5

Timer adjustment_03

Pump speed r/min 1150

Advance angle deg. 3 2.5 3.5

Timer adjustment_04

Pump speed r/min -

Advance angle deg. 4 4 4

Remarks
Measure the actual speed, stop

Test data Ex:

Governor adjustment

N:Pump speed R:Rack position (mm) (1)Adjust with speed control lever at full position (minimum-maximum speed specification) (2)Adjust with the load control lever in the full position (variable speed specification). (3)Rack limit using the stop lever: R1 (4)Damper spring setting: DL (5)Main spring setting (6)Set idle sub-spring
----------
R1=11.6mm DL=5.6-0.2mm
----------

Speed control lever angle

F:Full speed I:Idle
----------

----------
a=10deg+-5deg b=10deg+-5deg

0000000901

F:Full load I:Idle (1)Stopper bolt setting
----------

----------
a=24.5deg+-5deg b=38.5deg+-3deg

Stop lever angle

N:Pump normal S:Stop the pump. (1)Rack position = aa (2)Use the hole at R = bb
----------
aa=11.6mm bb=32mm
----------
a=29.5deg+-5deg b=4deg+-5deg

0000001501

(1)Pump vertical direction (2)Position of the coupling's key groove at the beginning of injection of the No. 8 cylinder. (3)- (4)-
----------

----------
a=(90deg)

Timing setting

(1)Pump vertical direction (2)Position of the coupling's key groove at the beginning of injection of the No. 8 cylinder. (3)- (4)-
----------

----------
a=(90deg)