106673-7930 ZEXEL 9 400 610 955 BOSCH INJECTION-PUMP ASSEMBLY 9400610955 1066737930


106673-7930 INJECTION-PUMP ASSEMBLY
Rating:
39
Buy INJECTION-PUMP ASSEMBLY 106673-7930 zexel genuine, new aftermarket engine parts with delivery

Information injection-pump assembly

BOSCH 9 400 610 955 9400610955
ZEXEL 106673-7930 1066737930

Service parts 106673-7930 INJECTION-PUMP ASSEMBLY:

1. _
2. FUEL INJECTION PUMP 106067-1140
3. GOVERNOR 105923-3680
4. SUPPLY PUMP 105237-4790
5. AUTOM. ADVANCE MECHANIS 105681-2140
6. COUPLING PLATE 105663-0820
7. COUPLING PLATE
8. _
9. _
10. NOZZLE AND HOLDER ASSY 105110-7371
11. Nozzle and Holder ME151161
12. Open Pre:MPa(Kqf/cm2) 15.7{160}/21.6{220}
13. NOZZLE-HOLDER 105041-4111
14. NOZZLE
15. NOZZLE SET 105019-0330

Include in #1:

106673-7930 as INJECTION-PUMP ASSEMBLY

Cross reference number

BOSCH 9 400 610 955 9400610955
ZEXEL 106673-7930 1066737930


Zexel num
Bosch num
Firm num
Name
106673-7930 
106673-7931 
9 400 610 955 
   
INJECTION-PUMP ASSEMBLY
* K 14CA PE6P,6PD PE

Calibration Data:

Adjustment conditions
Test oil
1404 Test oil
  ISO4113 or {SAEJ967d}
Test oil temperature degC   40 40 45
Nozzle and nozzle holder   105780-8250
Bosch type code   1 688 901 101
Nozzle   105780-0120
Bosch type code   1 688 901 990
Nozzle holder   105780-2190
Opening pressure MPa   20.7
Opening pressure kgf/cm2   211
Injection pipe
Outer diameter - inner diameter - length (mm)
mm   8-3-600
Overflow valve   131425-0220
Overflow valve opening pressure kPa   157 123 191
Overflow valve opening pressure kgf/cm2   1.6 1.25 1.95
Tester oil delivery pressure kPa   255 255 255
Tester oil delivery pressure kgf/cm2   2.6 2.6 2.6
Direction of rotation (viewed from drive side)
Right
  R
Injection timing adjustment
Direction of rotation (viewed from drive side)
Right
  R
Injection order   1-5-3-6- 2-4
Pre-stroke mm   3.9 3.85 3.95
Beginning of injection position
Governor side
  NO.1
Difference between angles 1
Cal 1-5
deg.   60 59.5 60.5
Difference between angles 2
Cal 1-3
deg.   120 119.5 120.5
Difference between angles 3
Cal 1-6
deg.   180 179.5 180.5
Difference between angles 4
Cyl.1-2
deg.   240 239.5 240.5
Difference between angles 5
Cal 1-4
deg.   300 299.5 300.5
Injection quantity adjustment
Adjusting point   -
Rack position   12.7
Pump speed r/min   700 700 700
Each cylinder's injection qty mm3/st.   147 143.3 150.7
Basic   *
Fixing the rack   *
Standard for adjustment of the maximum variation between cylinders   *
Injection quantity adjustment_02
Adjusting point   Z
Rack position   8+-0.5
Pump speed r/min   410 410 410
Each cylinder's injection qty mm3/st.   21 17.8 24.2
Fixing the rack   *
Standard for adjustment of the maximum variation between cylinders   *
Injection quantity adjustment_03
Adjusting point   A
Rack position   R1(12.7)
Pump speed r/min   700 700 700
Average injection quantity mm3/st.   147 146 148
Basic   *
Fixing the lever   *
Boost pressure kPa   37.3 37.3
Boost pressure mmHg   280 280
Injection quantity adjustment_04
Adjusting point   B
Rack position   R1+1.35
Pump speed r/min   1100 1100 1100
Average injection quantity mm3/st.   146 142 150
Fixing the lever   *
Boost pressure kPa   37.3 37.3
Boost pressure mmHg   280 280
Injection quantity adjustment_05
Adjusting point   D
Rack position   (R1-0.75 )
Pump speed r/min   500 500 500
Average injection quantity mm3/st.   144.5 138.5 150.5
Fixing the lever   *
Boost pressure kPa   37.3 37.3
Boost pressure mmHg   280 280
Boost compensator adjustment
Pump speed r/min   300 300 300
Rack position   R2-2
Boost pressure kPa   13.3 12 14.6
Boost pressure mmHg   100 90 110
Boost compensator adjustment_02
Pump speed r/min   300 300 300
Rack position   R2(R1-1. 1)
Boost pressure kPa   24 24 24
Boost pressure mmHg   180 180 180
Timer adjustment
Pump speed r/min   750--
Advance angle deg.   0 0 0
Remarks
Start
 
Timer adjustment_02
Pump speed r/min   700
Advance angle deg.   0.5
Timer adjustment_03
Pump speed r/min   1100
Advance angle deg.   2 1.5 2.5
Remarks
Finish
 

Test data Ex:

Governor adjustment

Test data 106673-7930
N:Pump speed R:Rack position (mm) (1)Torque cam stamping: T1 (2)Tolerance for racks not indicated: +-0.05mm. (3)Boost compensator stroke: BCL (4)Damper spring setting
----------
T1=AE16 BCL=2+-0.1mm
----------

Speed control lever angle

Test data 106673-7930
F:Full speed I:Idle (1)Viewed from feed pump side. (2)Use the hole at R = aa (3)Stopper bolt set position 'H'
----------
aa=37.5mm
----------
a=1deg+-5deg b=39deg+-3deg

Stop lever angle

Test data 106673-7930
N:Pump normal S:Stop the pump. (1)Use the hole at R = aa (2)Normal engine position (3)Set the stopper bolt so that speed = bb and rack position = cc. (Confirm non-injection.)
----------
aa=54mm bb=1100r/min cc=3.5+-0.3mm
----------
a=40deg+-5deg b=29.5deg+-5deg c=(38deg)

Timing setting

Test data 106673-7930
(1)Pump vertical direction (2)Coupling's key groove position at No 1 cylinder's beginning of injection (3)B.T.D.C.: aa (4)-
----------
aa=11deg
----------
a=(8deg)




Have questions with 106673-7930?





Group cross 106673-7930 ZEXEL

Mitsubishi 

9 400 617 361 
ME152595 
INJECTION-PUMP ASSEMBLY
6D24
9 400 619 957 
 
INJECTION-PUMP ASSEMBLY
 
 
INJECTION-PUMP ASSEMBLY

Mitsubishi 

9 400 611 392 
ME152635 
INJECTION-PUMP ASSEMBLY
6D24T2
 
 
INJECTION-PUMP ASSEMBLY

Mitsubishi 

9 400 617 362 
ME158460 
INJECTION-PUMP ASSEMBLY
6D24TC
106673-7930  

106673-7931 
9 400 610 955 
 
INJECTION-PUMP ASSEMBLY

Mitsubishi 

9 400 617 363 
ME152685 
INJECTION-PUMP ASSEMBLY
6D24T1
9 400 617 364 
ME152688 
INJECTION-PUMP ASSEMBLY
6D24
 
ME359605 
INJECTION-PUMP ASSEMBLY
6D24
9 400 617 365 
ME152689 
INJECTION-PUMP ASSEMBLY
6D24
9 400 611 462 
ME158505 
INJECTION-PUMP ASSEMBLY
6D24
F 019 Z20 138 
ME442607 
INJECTION-PUMP ASSEMBLY
6D24
9 400 611 463 
ME158506 
INJECTION-PUMP ASSEMBLY
6D24TC
F 019 Z20 139 
ME442608 
INJECTION-PUMP ASSEMBLY
6D24TC
9 400 611 955 
ME158507 
INJECTION-PUMP ASSEMBLY
6D24T
9 400 611 274 
ME158508 
INJECTION-PUMP ASSEMBLY
6D24TC
F 019 Z20 140 
ME442609 
INJECTION-PUMP ASSEMBLY
6D24TC
Back to top