106661-5570 ZEXEL INJECTION-PUMP ASSEMBLY Calibration Data 1066615570

Information Cross number Calibration Data Calibration Data Ex

Price: query
Buy now
Add to cart Go to cart

Rating:

Buy INJECTION-PUMP ASSEMBLY 106661-5570 zexel genuine, new aftermarket engine parts with delivery

Information injection-pump assembly

ZEXEL 106661-5570 1066615570

Service parts 106661-5570 INJECTION-PUMP ASSEMBLY:

1. _

2. FUEL INJECTION PUMP 106066-5460

3. GOVERNOR 105487-6850

4. SUPPLY PUMP 105217-1850

5. AUTOM. ADVANCE MECHANIS 105636-1710

6. COUPLING PLATE 105662-0751

7. COUPLING PLATE

8. _

9. _

10. NOZZLE AND HOLDER ASSY 105100-5950

11. Nozzle and Holder 16600-96510

12. Open Pre:MPa(Kqf/cm2) 19.6{200}

13. NOZZLE-HOLDER 105031-4370

14. NOZZLE 105015-5580

15. NOZZLE SET

Include in #1:

106661-5570 as INJECTION-PUMP ASSEMBLY

Cross reference number

ZEXEL 106661-5570 1066615570

Zexel num

Bosch num

Firm num

Name

106661-5570

INJECTION-PUMP ASSEMBLY

Calibration Data:

Adjustment conditions

Test oil
1404 Test oil ISO4113 or {SAEJ967d}

Test oil temperature degC 40 40 45

Nozzle and nozzle holder 105780-8140

Bosch type code EF8511/9A

Nozzle 105780-0000

Bosch type code DN12SD12T

Nozzle holder 105780-2080

Bosch type code EF8511/9

Opening pressure MPa 17.2

Opening pressure kgf/cm2 175

Injection pipe
Outer diameter - inner diameter - length (mm) mm 8-3-600

Overflow valve 132424-0620

Overflow valve opening pressure kPa 157 123 191

Overflow valve opening pressure kgf/cm2 1.6 1.25 1.95

Tester oil delivery pressure kPa 157 157 157

Tester oil delivery pressure kgf/cm2 1.6 1.6 1.6

Direction of rotation (viewed from drive side)
Right R

Injection timing adjustment

Direction of rotation (viewed from drive side)
Right R

Injection order 1-4-2-6- 3-5

Pre-stroke mm 3.65 3.6 3.7

Beginning of injection position
Drive side NO.1

Difference between angles 1
Cal 1-4 deg. 60 59.5 60.5

Difference between angles 2
Cyl.1-2 deg. 120 119.5 120.5

Difference between angles 3
Cal 1-6 deg. 180 179.5 180.5

Difference between angles 4
Cal 1-3 deg. 240 239.5 240.5

Difference between angles 5
Cal 1-5 deg. 300 299.5 300.5

Injection quantity adjustment

Adjusting point A

Rack position 9

Pump speed r/min 600 600 600

Average injection quantity mm3/st. 117.5 116.5 118.5

Max. variation between cylinders % 0 -4 4

Basic *

Fixing the lever *

Injection quantity adjustment_02

Adjusting point B

Rack position 5+-0.5

Pump speed r/min 240 240 240

Average injection quantity mm3/st. 9.5 8.2 10.8

Max. variation between cylinders % 0 -10 10

Fixing the rack *

Timer adjustment

Pump speed r/min 950--

Advance angle deg. 0 0 0

Remarks
Start

Timer adjustment_02

Pump speed r/min 900

Advance angle deg. 0.5

Timer adjustment_03

Pump speed r/min 1150

Advance angle deg. 5 4.5 5.5

Remarks
Finish

Test data Ex:

Governor adjustment

N:Pump speed R:Rack position (mm) (1)Lever ratio: RT (2)Target shim dimension: TH (3)Tolerance for racks not indicated: +-0.05mm. (4)Rack limit using the stop lever: R1 (5)Excess fuel setting for starting: SXL (N = N1) (6)Damper spring setting
----------
RT=1 TH=2.3mm R1=10.8+0.2mm SXL9+0.2mm N1=430r/min
----------

Speed control lever angle

F:Full speed
----------

----------
a=21deg+-5deg

0000000901

F:Full load I:Idle (1)Stopper bolt setting (2)At center of threaded hole above R = aa
----------
aa=17mm
----------
a=15deg+-5deg b=29deg+-3deg

Stop lever angle

N:Pump normal S:Stop the pump. (1)Drive side (2)Use the hole at R = aa (3)Rack position bb
----------
aa=50mm bb=10.8+0.2mm
----------
a=26deg+-5deg b=28deg+-5deg

0000001501 ACS

(A) Set screw 1. Aneroid compensator unit adjustment Screw in (A) to obtain L1. 2. Adjustment following governor installation (1)Set the speed of the pump to N1 r/min and fix the control lever at the full set position. (2)Screw in the aneroid compensator to obtain the performance shown in the graph above.
----------
N1=600r/min L1=0.1~0.5mm
----------
R1=9mm R2=(8)mm P1=89+-2.7kPa(668+-20mmHg) P2=70+-0.7kPa(525+-5mmHg) Q1=117.5+-1cm3/1000st Q2=93.5+-2cm3/1000st