101608-6522 ZEXEL F 019 Z10 297 BOSCH INJECTION-PUMP ASSEMBLY f019z10297 1016086522 me441718


101608-6522 INJECTION-PUMP ASSEMBLY
Rating:
79
Buy INJECTION-PUMP ASSEMBLY 101608-6522 zexel genuine, new aftermarket engine parts with delivery

Information injection-pump assembly

BOSCH F 019 Z10 297 f019z10297
ZEXEL 101608-6522 1016086522
MITSUBISHI ME441718 me441718

Service parts 101608-6522 INJECTION-PUMP ASSEMBLY:

1. _
2. FUEL INJECTION PUMP 101062-9290
3. GOVERNOR 105401-1480
4. SUPPLY PUMP 105220-7110
5. AUTOM. ADVANCE MECHANIS 105676-1320
6. COUPLING PLATE
7. COUPLING PLATE
8. _
9. _
10. NOZZLE AND HOLDER ASSY 105118-6920
11. Nozzle and Holder ME440837
12. Open Pre:MPa(Kqf/cm2) 21.6(220)
13. NOZZLE-HOLDER 105048-3590
14. NOZZLE 105017-3120
15. NOZZLE SET

Include in #1:

101608-6522 as INJECTION-PUMP ASSEMBLY

Include in #2:

Cross reference number

BOSCH F 019 Z10 297 f019z10297
ZEXEL 101608-6522 1016086522
MITSUBISHI ME441718 me441718


Zexel num
Bosch num
Firm num
Name
101608-6522 
F 019 Z10 297 
ME441718  MITSUBISHI
INJECTION-PUMP ASSEMBLY
6D34TL K 14BE INJECTION PUMP ASSY PE6A PE

Calibration Data:

Adjustment conditions
Test oil
1404 Test oil
  ISO4113 or {SAEJ967d}
Test oil temperature degC   40 40 45
Nozzle and nozzle holder   105780-8140
Bosch type code   EF8511/9A
Nozzle   105780-0000
Bosch type code   DN12SD12T
Nozzle holder   105780-2080
Bosch type code   EF8511/9
Opening pressure MPa   17.2
Opening pressure kgf/cm2   175
Injection pipe
Outer diameter - inner diameter - length (mm)
mm   6-2-600
Overflow valve   131424-5520
Overflow valve opening pressure kPa   255 221 289
Overflow valve opening pressure kgf/cm2   2.6 2.25 2.95
Tester oil delivery pressure kPa   255 255 255
Tester oil delivery pressure kgf/cm2   2.6 2.6 2.6
Direction of rotation (viewed from drive side)
Right
  R
Injection timing adjustment
Direction of rotation (viewed from drive side)
Right
  R
Injection order   1-5-3-6- 2-4
Pre-stroke mm   3.2 3.15 3.25
Beginning of injection position
Drive side
  NO.1
Difference between angles 1
Cal 1-5
deg.   60 59.5 60.5
Difference between angles 2
Cal 1-3
deg.   120 119.5 120.5
Difference between angles 3
Cal 1-6
deg.   180 179.5 180.5
Difference between angles 4
Cyl.1-2
deg.   240 239.5 240.5
Difference between angles 5
Cal 1-4
deg.   300 299.5 300.5
Injection quantity adjustment
Adjusting point   A
Rack position   10
Pump speed r/min   1085 1085 1085
Average injection quantity mm3/st.   95 94 96
Max. variation between cylinders %   0 -2.5 2.5
Basic   *
Fixing the lever   *
Boost pressure kPa   80 80
Boost pressure mmHg   600 600
Injection quantity adjustment_02
Adjusting point   -
Rack position   7.3+-0.5
Pump speed r/min   515 515 515
Average injection quantity mm3/st.   8 6.7 9.3
Max. variation between cylinders %   0 -14 14
Fixing the rack   *
Boost pressure kPa   0 0 0
Boost pressure mmHg   0 0 0
Remarks
Adjust only variation between cylinders; adjust governor according to governor specifications.
 
Injection quantity adjustment_03
Adjusting point   E
Rack position   10.2++
Pump speed r/min   100 100 100
Average injection quantity mm3/st.   65 65 70
Fixing the lever   *
Boost pressure kPa   0 0 0
Boost pressure mmHg   0 0 0
Rack limit   *
Boost compensator adjustment
Pump speed r/min   900 900 900
Rack position   R1-1.05
Boost pressure kPa   24 17.3 30.7
Boost pressure mmHg   180 130 230
Boost compensator adjustment_02
Pump speed r/min   900 900 900
Rack position   R1(10)
Boost pressure kPa   70.6 67.9 73.3
Boost pressure mmHg   530 510 550
Timer adjustment
Pump speed r/min   0
Advance angle deg.   3 2 3
Load   0/4
Timer adjustment_02
Pump speed r/min   650+-25
Advance angle deg.   3 2 3
Load   0/4
Remarks
Start
 
Timer adjustment_03
Pump speed r/min   750+-25
Advance angle deg.   0 0 0
Load   0/4
Remarks
Finish
 

Test data Ex:

Governor adjustment

Test data 101608-6522
N:Pump speed R:Rack position (mm) (1)Target notch: K (2)Tolerance for racks not indicated: +-0.05mm. (3)RACK LIMIT (4)Set idle sub-spring (5)Main spring setting (6)Boost compensator stroke: BCL
----------
K=12 BCL=1.05+-0.1mm
----------

Speed control lever angle

Test data 101608-6522
F:Full speed I:Idle (1)Stopper bolt setting (2)Base lever only
----------

----------
a=3.5deg+-5deg b=19deg+-5deg

Stop lever angle

Test data 101608-6522
N:Pump normal S:Stop the pump. (1)Pump speed aa and rack position bb (to be sealed at delivery) (2)Normal
----------
aa=0r/min bb=4-0.5mm
----------
a=14deg+-5deg b=(48deg)

Timing setting

Test data 101608-6522
(1)Pump vertical direction (2)Position of gear mark '3' at No 1 cylinder's beginning of injection (3)B.T.D.C.: aa (4)-
----------
aa=10deg
----------
a=(130deg)




Have questions with 101608-6522?





Group cross 101608-6522 ZEXEL

9 400 619 517 
 
INJECTION-PUMP ASSEMBLY

Mitsubishi 

9 400 615 857 
ME441559 
INJECTION-PUMP ASSEMBLY
6D16TL
9 400 619 518 
 
INJECTION-PUMP ASSEMBLY
9 400 613 229 
 
INJECTION-PUMP ASSEMBLY

Mitsubishi 

F 019 Z20 027 
ME441578 
INJECTION-PUMP ASSEMBLY
6D16TL
9 400 613 384 
 
INJECTION-PUMP ASSEMBLY
9 400 619 712 
 
INJECTION-PUMP ASSEMBLY

Mitsubishi 

101608-6522  
F 019 Z10 297 
ME441718 
INJECTION-PUMP ASSEMBLY
6D34TL
9 400 613 296 
 
INJECTION-PUMP ASSEMBLY
 
 
INJECTION-PUMP ASSEMBLY

Mitsubishi 

F 019 Z20 028 
ME441044 
INJECTION-PUMP ASSEMBLY
6D34TL
F 01G 09U 0J9 
ME443900 
INJECTION-PUMP ASSEMBLY
6D34TL
9 400 619 604 
 
INJECTION-PUMP ASSEMBLY

Mitsubishi 

F 019 Z20 029 
ME442589 
INJECTION-PUMP ASSEMBLY
6D34TL
F 019 Z20 030 
ME442887 
INJECTION-PUMP ASSEMBLY
6D16TL
Back to top