101606-9420 ZEXEL F 019 Z10 370 BOSCH INJECTION-PUMP ASSEMBLY f019z10370 1016069420 16713z6160


101606-9420 INJECTION-PUMP ASSEMBLY
Rating:
9
Buy INJECTION-PUMP ASSEMBLY 101606-9420 zexel genuine, new aftermarket engine parts with delivery

Information injection-pump assembly

BOSCH F 019 Z10 370 f019z10370
ZEXEL 101606-9420 1016069420
NISSAN-DIESEL 16713Z6160 16713z6160

Service parts 101606-9420 INJECTION-PUMP ASSEMBLY:

1. _
2. FUEL INJECTION PUMP 101060-5270
3. GOVERNOR 105921-7130
4. SUPPLY PUMP 105220-7010
5. AUTOM. ADVANCE MECHANIS 105614-3600
6. COUPLING PLATE 105662-1340
7. COUPLING PLATE
8. _
9. _
10. NOZZLE AND HOLDER ASSY 105101-6890
11. Nozzle and Holder 16600-Z5609
12. Open Pre:MPa(Kqf/cm2) 19.6{200}
13. NOZZLE-HOLDER 105030-3490
14. NOZZLE 105015-9460
15. NOZZLE SET

Include in #1:

101606-9420 as INJECTION-PUMP ASSEMBLY

Cross reference number

BOSCH F 019 Z10 370 f019z10370
ZEXEL 101606-9420 1016069420
NISSAN-DIESEL 16713Z6160 16713z6160


Zexel num
Bosch num
Firm num
Name
101606-9420 
101606-9421 
F 019 Z10 370 
16713Z6160  NISSAN-DIESEL
INJECTION-PUMP ASSEMBLY
FE6E * K

Calibration Data:

Adjustment conditions
Test oil
1404 Test oil
  ISO4113 or {SAEJ967d}
Test oil temperature degC   40 40 45
Nozzle and nozzle holder   105780-8140
Bosch type code   EF8511/9A
Nozzle   105780-0000
Bosch type code   DN12SD12T
Nozzle holder   105780-2080
Bosch type code   EF8511/9
Opening pressure MPa   17.2
Opening pressure kgf/cm2   175
Injection pipe
Outer diameter - inner diameter - length (mm)
mm   6-2-600
Overflow valve   134424-1520
Overflow valve opening pressure kPa   162 147 177
Overflow valve opening pressure kgf/cm2   1.65 1.5 1.8
Tester oil delivery pressure kPa   157 157 157
Tester oil delivery pressure kgf/cm2   1.6 1.6 1.6
Direction of rotation (viewed from drive side)
Right
  R
Injection timing adjustment
Direction of rotation (viewed from drive side)
Right
  R
Injection order   1-4-2-6- 3-5
Pre-stroke mm   3.7 3.65 3.75
Beginning of injection position
Drive side
  NO.1
Difference between angles 1
Cal 1-4
deg.   60 59.5 60.5
Difference between angles 2
Cyl.1-2
deg.   120 119.5 120.5
Difference between angles 3
Cal 1-6
deg.   180 179.5 180.5
Difference between angles 4
Cal 1-3
deg.   240 239.5 240.5
Difference between angles 5
Cal 1-5
deg.   300 299.5 300.5
Injection quantity adjustment
Adjusting point   -
Rack position   11.5
Pump speed r/min   800 800 800
Average injection quantity mm3/st.   78 76.4 79.6
Max. variation between cylinders %   0 -3.5 3.5
Basic   *
Fixing the rack   *
Standard for adjustment of the maximum variation between cylinders   *
Injection quantity adjustment_02
Adjusting point   H
Rack position   9.5+-0.5
Pump speed r/min   275 275 275
Average injection quantity mm3/st.   12.5 10.7 14.3
Max. variation between cylinders %   0 -10 10
Fixing the rack   *
Standard for adjustment of the maximum variation between cylinders   *
Injection quantity adjustment_03
Adjusting point   A
Rack position   R1(11.5)
Pump speed r/min   800 800 800
Average injection quantity mm3/st.   78 77 79
Basic   *
Fixing the lever   *
Injection quantity adjustment_04
Adjusting point   B
Rack position   R1-0.05
Pump speed r/min   1500 1500 1500
Average injection quantity mm3/st.   87.5 83.5 91.5
Fixing the lever   *
Injection quantity adjustment_05
Adjusting point   C
Rack position   R1-0.35
Pump speed r/min   600 600 600
Average injection quantity mm3/st.   63 59.8 66.2
Fixing the lever   *
Injection quantity adjustment_06
Adjusting point   I
Rack position   -
Pump speed r/min   100 100 100
Average injection quantity mm3/st.   105 105 115
Fixing the lever   *
Rack limit   *
Timer adjustment
Pump speed r/min   (1087)
Advance angle deg.   0 0 0
Remarks
Start
 
Timer adjustment_02
Pump speed r/min   1200
Advance angle deg.   1.5 1 2
Timer adjustment_03
Pump speed r/min   1500
Advance angle deg.   5.5 5 6
Remarks
Finish
 

Test data Ex:

Governor adjustment

Test data 101606-9420
N:Pump speed R:Rack position (mm) (1)Torque cam stamping: T1 (2)Tolerance for racks not indicated: +-0.05mm. (3)RACK LIMIT
----------
T1=J01
----------

Speed control lever angle

Test data 101606-9420
F:Full speed I:Idle (1)Use the hole at R = aa (2)Stopper bolt set position 'H'
----------
aa=39mm
----------
a=17deg+-5deg b=34.5deg+-3deg

Stop lever angle

Test data 101606-9420
N:Pump normal S:Stop the pump. (1)Use the pin at R = aa
----------
aa=42mm
----------
a=40deg+-5deg b=25deg+-5deg

0000001501 LEVER

Test data 101606-9420
(a) Speed lever (B) Accelerator lever (C) Accelerator lever stopper bolt 1. Accelerator lever setting method With the speed lever in the idling position, back off the accelerator lever stopper bolt L1 from where it contacts point a. (Back off 1+0.5 turns and set.)
----------
L1=1+0.5 mm
----------

Timing setting

Test data 101606-9420
(1)Pump vertical direction (2)Position of timer's threaded hole at No 1 cylinder's beginning of injection (3)- (4)-
----------

----------
a=(60deg)




Have questions with 101606-9420?





Group cross 101606-9420 ZEXEL

9 400 619 523 
 
INJECTION-PUMP ASSEMBLY

Nissan-Diesel 

F 019 Z10 369 
16790Z5600 
INJECTION-PUMP ASSEMBLY
FD606
101606-9420  

101606-9421 
F 019 Z10 370 
16713Z6160 
INJECTION-PUMP ASSEMBLY
FE6E
9 400 615 563 
16713Z6908 
INJECTION-PUMP ASSEMBLY
FE6E
 
16713Z6167 
INJECTION-PUMP ASSEMBLY
FE6E

Hyundai 

9 400 615 564 
3310083C25 
INJECTION-PUMP ASSEMBLY
6D22

Nissan-Diesel 

9 400 615 565 
16790Z5601 
INJECTION-PUMP ASSEMBLY
FD606
9 400 619 555 
 
INJECTION-PUMP ASSEMBLY

Dpico 

9 400 613 053 
 
INJECTION-PUMP ASSEMBLY
EM100

Nissan-Diesel 

 
16713Z6178 
INJECTION-PUMP ASSEMBLY
FE6E
9 400 615 566 
16700Z5709 
INJECTION-PUMP ASSEMBLY
FE6B
9 400 615 567 
16700Z5710 
INJECTION-PUMP ASSEMBLY
FE6B
Back to top