101602-4001 ZEXEL 9 400 619 719 BOSCH INJECTION-PUMP ASSEMBLY 9400619719 1016024001 1156012634

Information Cross number Calibration Data Calibration Data Ex

Price: query
Buy now
Add to cart Go to cart

Rating:

Buy INJECTION-PUMP ASSEMBLY 101602-4001 zexel genuine, new aftermarket engine parts with delivery

Information injection-pump assembly

BOSCH 9 400 619 719 9400619719

ZEXEL 101602-4001 1016024001

ISUZU 1156012634 1156012634

Service parts 101602-4001 INJECTION-PUMP ASSEMBLY:

1. _

2. FUEL INJECTION PUMP 101060-8770

3. GOVERNOR 105950-0110

4. SUPPLY PUMP 105220-7260

5. AUTOM. ADVANCE MECHANIS

6. COUPLING PLATE

7. COUPLING PLATE 156636-5520

8. _

9. _

10. NOZZLE AND HOLDER ASSY 105100-4823

11. Nozzle and Holder 1-15300-104-2

12. Open Pre:MPa(Kqf/cm2) 18.1{185}

13. NOZZLE-HOLDER 105030-3201

14. NOZZLE

105015-4130

15. NOZZLE SET

Include in #1:

101402-7070 as _

101602-4001 as INJECTION-PUMP ASSEMBLY

Cross reference number

BOSCH 9 400 619 719 9400619719

ZEXEL 101602-4001 1016024001

ISUZU 1156012634 1156012634

Zexel num

Bosch num

Firm num

Name

101602-4001

9 400 619 719

1156012634 ISUZU

INJECTION-PUMP ASSEMBLY
6BD1-T * K 14BE PE6A PE

Calibration Data:

Adjustment conditions

Test oil
1404 Test oil ISO4113 or {SAEJ967d}

Test oil temperature degC 40 40 45

Nozzle and nozzle holder 105780-8140

Bosch type code EF8511/9A

Nozzle 105780-0000

Bosch type code DN12SD12T

Nozzle holder 105780-2080

Bosch type code EF8511/9

Opening pressure MPa 17.2

Opening pressure kgf/cm2 175

Injection pipe
Outer diameter - inner diameter - length (mm) mm 6-2-600

Overflow valve opening pressure kPa 157 123 191

Overflow valve opening pressure kgf/cm2 1.6 1.25 1.95

Tester oil delivery pressure kPa 157 157 157

Tester oil delivery pressure kgf/cm2 1.6 1.6 1.6

Direction of rotation (viewed from drive side)
Right R

Injection timing adjustment

Direction of rotation (viewed from drive side)
Right R

Injection order 1-5-3-6- 2-4

Pre-stroke mm 3.2 3.15 3.25

Beginning of injection position
Drive side NO.1

Difference between angles 1
Cal 1-5 deg. 60 59.5 60.5

Difference between angles 2
Cal 1-3 deg. 120 119.5 120.5

Difference between angles 3
Cal 1-6 deg. 180 179.5 180.5

Difference between angles 4
Cyl.1-2 deg. 240 239.5 240.5

Difference between angles 5
Cal 1-4 deg. 300 299.5 300.5

Injection quantity adjustment

Adjusting point A

Rack position 8.6

Pump speed r/min 900 900 900

Average injection quantity mm3/st. 66.5 65 68

Max. variation between cylinders % 0 -2.5 2.5

Basic *

Fixing the rack *

Injection quantity adjustment_02

Adjusting point B

Rack position 5.6+-0.5

Pump speed r/min 325 325 325

Average injection quantity mm3/st. 10.2 8.9 11.5

Max. variation between cylinders % 0 -14 14

Fixing the rack *

Test data Ex:

Governor adjustment

N:Pump speed R:Rack position (mm) (1)Set using the full load screw. (2)With isochronous switch ON (3)With isochronous switch OFF (parallel), to prevent overrunning. (4)With isochronous switch OFF, set at shipping (only) (5)Idle overrunning test possible until N1.
----------
N1=1170r/min
----------

Stop lever angle

N:Pump normal S:Stop the pump.
----------

----------
a=20deg+-5deg b=33deg+-5deg

Timing setting

(1)Pump vertical direction (2)Position of gear mark 'CC' at No 1 cylinder's beginning of injection (3)B.T.D.C.: aa (4)-
----------
aa=16deg
----------
a=(90deg)