Rating:
Information injection-pump assembly
ZEXEL
101481-9322
1014819322
NISSAN-DIESEL
1679090305
1679090305
Service parts 101481-9322 INJECTION-PUMP ASSEMBLY:
1.
_
6.
COUPLING PLATE
7.
COUPLING PLATE
8.
_
9.
_
11.
Nozzle and Holder
16600-01T61
12.
Open Pre:MPa(Kqf/cm2)
21.6{220}
15.
NOZZLE SET
Cross reference number
ZEXEL
101481-9322
1014819322
NISSAN-DIESEL
1679090305
1679090305
Zexel num
Bosch num
Firm num
Name
101481-9322
1679090305 NISSAN-DIESEL
INJECTION-PUMP ASSEMBLY
FD35T04 * K
FD35T04 * K
Calibration Data:
Adjustment conditions
Test oil
1404 Test oil ISO4113 or {SAEJ967d}
1404 Test oil ISO4113 or {SAEJ967d}
Test oil temperature
degC
40
40
45
Nozzle and nozzle holder
105780-8140
Bosch type code
EF8511/9A
Nozzle
105780-0000
Bosch type code
DN12SD12T
Nozzle holder
105780-2080
Bosch type code
EF8511/9
Opening pressure
MPa
17.2
Opening pressure
kgf/cm2
175
Injection pipe
Outer diameter - inner diameter - length (mm) mm 6-2-600
Outer diameter - inner diameter - length (mm) mm 6-2-600
Overflow valve
131424-1520
Overflow valve opening pressure
kPa
157
123
191
Overflow valve opening pressure
kgf/cm2
1.6
1.25
1.95
Tester oil delivery pressure
kPa
157
157
157
Tester oil delivery pressure
kgf/cm2
1.6
1.6
1.6
Direction of rotation (viewed from drive side)
Right R
Right R
Injection timing adjustment
Direction of rotation (viewed from drive side)
Right R
Right R
Injection order
1-3-4-2
Pre-stroke
mm
2.8
2.75
2.85
Beginning of injection position
Drive side NO.1
Drive side NO.1
Difference between angles 1
Cal 1-3 deg. 90 89.5 90.5
Cal 1-3 deg. 90 89.5 90.5
Difference between angles 2
Cal 1-4 deg. 180 179.5 180.5
Cal 1-4 deg. 180 179.5 180.5
Difference between angles 3
Cyl.1-2 deg. 270 269.5 270.5
Cyl.1-2 deg. 270 269.5 270.5
Injection quantity adjustment
Adjusting point
A
Rack position
10
Pump speed
r/min
1100
1100
1100
Average injection quantity
mm3/st.
67.2
66.2
68.2
Max. variation between cylinders
%
0
-3.5
3.5
Basic
*
Fixing the lever
*
Boost pressure
kPa
70
70
Boost pressure
mmHg
525
525
Injection quantity adjustment_02
Adjusting point
-
Rack position
7.8+-0.5
Pump speed
r/min
300
300
300
Average injection quantity
mm3/st.
10
8
12
Max. variation between cylinders
%
0
-10
10
Fixing the rack
*
Boost pressure
kPa
0
0
0
Boost pressure
mmHg
0
0
0
Remarks
Adjust only variation between cylinders; adjust governor according to governor specifications.
Adjust only variation between cylinders; adjust governor according to governor specifications.
Injection quantity adjustment_03
Adjusting point
C
Rack position
-
Pump speed
r/min
100
100
100
Average injection quantity
mm3/st.
81
81
91
Fixing the lever
*
Boost pressure
kPa
0
0
0
Boost pressure
mmHg
0
0
0
Rack limit
*
Boost compensator adjustment
Pump speed
r/min
500
500
500
Rack position
R1-0.3
Boost pressure
kPa
21.3
21.3
21.3
Boost pressure
mmHg
160
160
160
Boost compensator adjustment_02
Pump speed
r/min
500
500
500
Rack position
R1(10)
Boost pressure
kPa
60
56.7
63.3
Boost pressure
mmHg
450
425
475
Timer adjustment
Pump speed
r/min
700
Advance angle
deg.
0.5
Timer adjustment_02
Pump speed
r/min
1200
Advance angle
deg.
1.2
0.7
1.7
Timer adjustment_03
Pump speed
r/min
1600
Advance angle
deg.
3
2.5
3.5
Remarks
Finish
Finish
Test data Ex:
Governor adjustment
N:Pump speed
R:Rack position (mm)
(1)Target notch: K
(2)Tolerance for racks not indicated: +-0.05mm.
(3)RACK LIMIT
(4)Boost compensator stroke
----------
K=15
----------
----------
K=15
----------
Speed control lever angle
F:Full speed
I:Idle
(1)Stopper bolt setting
----------
----------
a=28deg+-5deg b=35deg+-5deg
----------
----------
a=28deg+-5deg b=35deg+-5deg
Stop lever angle
N:Pump normal
S:Stop the pump.
----------
----------
a=16.5deg+-5deg b=50deg+-5deg
----------
----------
a=16.5deg+-5deg b=50deg+-5deg
0000001501 GOV FULL LOAD ADJUSTMENT
Title1:Full load stopper adjustment
Title2:Governor set speed
LABEL1:Distinguishing
LABEL2:Pump speed (r/min)
LABEL3:Ave. injection quantity (mm3/st)
LABEL4:Max. var. bet. cyl.
LABEL5:Remarks
LABEL6:Distinguishing
LABEL7:Governor set speed (r/min)
LABEL8:Maximum no-load speed (r/min)
LABEL9:Remarks
(1)Adjustment conditions are the same as those for measuring injection quantity.
(2)At high idle rack position L
----------
L=5.5mm
----------
a1=A a2=B a3=C a4=- a5=- a6=- r1=- r2=1100r/min r3=- r4=- r5=- r6=- Q1=- Q2=67.2+-1mm3/st Q3=- Q4=- Q5=- Q6=- c1=- c2=+-3.5% c3=- c4=- c5=- c6=- a7=32 a8=31 a9=30 a10=29 a11=28 a12=27 a13=26 a14=25 a15=24 a16=23 a17=22 a18=21 a19=20 a20=19 a21=18 a22=- a23=- a24=- a25=- a26=- a27=- a28=- r7=1600r/min r8=1550r/min r9=1500r/min r10=1450r/min r11=1400r/min r12=1350r/min r13=1300r/min r14=1250r/min r15=1200r/min r16=1150r/min r17=1100r/min r18=1050r/min r19=1000r/min r20=950r/min r21=900r/min r22=- r23=- r24=- r25=- r26=- r27=- r28=- R7=1720+-40r/min R8=1665+-38r/min R9=1610+-37r/min R10=1555+-36r/min R11=1505+-35r/min R12=1450+-33r/min R13=1395+-32r/min R14=1340+-31r/min R15=1290+-30r/min R16=1235+-28r/min R17=1180+-27r/min R18=1130+-26r/min R19=1075+-26r/min R20=1020+-23r/min R21=965+-22r/min R22=- R23=- R24=- R25=- R26=- R27=- R28=-
----------
L=5.5mm
----------
a1=A a2=B a3=C a4=- a5=- a6=- r1=- r2=1100r/min r3=- r4=- r5=- r6=- Q1=- Q2=67.2+-1mm3/st Q3=- Q4=- Q5=- Q6=- c1=- c2=+-3.5% c3=- c4=- c5=- c6=- a7=32 a8=31 a9=30 a10=29 a11=28 a12=27 a13=26 a14=25 a15=24 a16=23 a17=22 a18=21 a19=20 a20=19 a21=18 a22=- a23=- a24=- a25=- a26=- a27=- a28=- r7=1600r/min r8=1550r/min r9=1500r/min r10=1450r/min r11=1400r/min r12=1350r/min r13=1300r/min r14=1250r/min r15=1200r/min r16=1150r/min r17=1100r/min r18=1050r/min r19=1000r/min r20=950r/min r21=900r/min r22=- r23=- r24=- r25=- r26=- r27=- r28=- R7=1720+-40r/min R8=1665+-38r/min R9=1610+-37r/min R10=1555+-36r/min R11=1505+-35r/min R12=1450+-33r/min R13=1395+-32r/min R14=1340+-31r/min R15=1290+-30r/min R16=1235+-28r/min R17=1180+-27r/min R18=1130+-26r/min R19=1075+-26r/min R20=1020+-23r/min R21=965+-22r/min R22=- R23=- R24=- R25=- R26=- R27=- R28=-
Timing setting
(1)Pump vertical direction
(2)Position of gear's standard threaded hole at No 1 cylinder's beginning of injection (position of gear's 'M' mark)
(3)B.T.D.C.: aa
(4)-
----------
aa=13deg
----------
a=(60deg)
----------
aa=13deg
----------
a=(60deg)
Have questions with 101481-9322?
Group cross 101481-9322 ZEXEL
Nissan-Diesel
Nissan-Diesel
Nissan-Diesel
101481-9322
1679090305
INJECTION-PUMP ASSEMBLY
FD35T04
FD35T04