101481-9370 ZEXEL INJECTION-PUMP ASSEMBLY Calibration Data 1014819370 1679090368


101481-9370 INJECTION-PUMP ASSEMBLY
Rating:
78
Buy INJECTION-PUMP ASSEMBLY 101481-9370 zexel genuine, new aftermarket engine parts with delivery

Information injection-pump assembly

ZEXEL 101481-9370 1014819370
NISSAN-DIESEL 1679090368 1679090368

Service parts 101481-9370 INJECTION-PUMP ASSEMBLY:

1. _
2. FUEL INJECTION PUMP 101048-8160
3. GOVERNOR 105419-1850
4. SUPPLY PUMP 105220-5740
5. AUTOM. ADVANCE MECHANIS 105622-1890
6. COUPLING PLATE
7. COUPLING PLATE
8. _
9. _
10. NOZZLE AND HOLDER ASSY 105118-5780
11. Nozzle and Holder 16600-90074
12. Open Pre:MPa(Kqf/cm2) 15.7{160}
13. NOZZLE-HOLDER 105048-3390
14. NOZZLE 105017-0900
15. NOZZLE SET

Include in #1:

101481-9370 as INJECTION-PUMP ASSEMBLY

Cross reference number

ZEXEL 101481-9370 1014819370
NISSAN-DIESEL 1679090368 1679090368


Zexel num
Bosch num
Firm num
Name
101481-9370 
101481-9371 
 
1679090368  NISSAN-DIESEL
INJECTION-PUMP ASSEMBLY
BD30 * K

Calibration Data:

Adjustment conditions
Test oil
1404 Test oil
  ISO4113 or {SAEJ967d}
Test oil temperature degC   40 40 45
Nozzle and nozzle holder   105780-8140
Bosch type code   EF8511/9A
Nozzle   105780-0000
Bosch type code   DN12SD12T
Nozzle holder   105780-2080
Bosch type code   EF8511/9
Opening pressure MPa   17.2
Opening pressure kgf/cm2   175
Injection pipe
Outer diameter - inner diameter - length (mm)
mm   6-2-600
Overflow valve   131424-1520
Overflow valve opening pressure kPa   157 123 191
Overflow valve opening pressure kgf/cm2   1.6 1.25 1.95
Tester oil delivery pressure kPa   157 157 157
Tester oil delivery pressure kgf/cm2   1.6 1.6 1.6
Direction of rotation (viewed from drive side)
Right
  R
Injection timing adjustment
Direction of rotation (viewed from drive side)
Right
  R
Injection order   1-3-4-2
Pre-stroke mm   3.2 3.15 3.25
Beginning of injection position
Drive side
  NO.1
Difference between angles 1
Cal 1-3
deg.   90 89.5 90.5
Difference between angles 2
Cal 1-4
deg.   180 179.5 180.5
Difference between angles 3
Cyl.1-2
deg.   270 269.5 270.5
Injection quantity adjustment
Adjusting point   A
Rack position   9.9
Pump speed r/min   1100 1100 1100
Average injection quantity mm3/st.   42.2 41.2 43.2
Max. variation between cylinders %   0 -3.5 3.5
Basic   *
Fixing the lever   *
Injection quantity adjustment_02
Adjusting point   -
Rack position   9.2+-0.5
Pump speed r/min   425 425 425
Average injection quantity mm3/st.   8 6 10
Max. variation between cylinders %   0 -10 10
Fixing the rack   *
Remarks
Adjust only variation between cylinders; adjust governor according to governor specifications.
 
Injection quantity adjustment_03
Adjusting point   D
Rack position   -
Pump speed r/min   100 100 100
Average injection quantity mm3/st.   65 65 75
Fixing the lever   *
Rack limit   *
Timer adjustment
Pump speed r/min   1100
Advance angle deg.   0.5
Timer adjustment_02
Pump speed r/min   1500
Advance angle deg.   2 1.5 2.5
Timer adjustment_03
Pump speed r/min   1600
Advance angle deg.   2.5 2 3
Remarks
Finish
 

Test data Ex:

Governor adjustment

Test data 101481-9370
N:Pump speed R:Rack position (mm) (1)Target notch: K (2)Tolerance for racks not indicated: +-0.05mm. (3)RACK LIMIT (4)Set idle sub-spring (5)Main spring setting (6)Rack difference between N = N1 and N = N2
----------
K=16 N1=1100r/min N2=700r/min
----------

Speed control lever angle

Test data 101481-9370
F:Full speed I:Idle (1)Stopper bolt setting
----------

----------
a=(37deg)+-5deg b=(32deg)+-5deg

Stop lever angle

Test data 101481-9370
N:Pump normal S:Stop the pump.
----------

----------
a=12deg+-5deg b=53deg+-5deg

0000001501 GOV FULL LOAD ADJUSTMENT

Test data 101481-9370
Title1:Full load stopper adjustment Title2:Governor set speed LABEL1:Distinguishing LABEL2:Pump speed (r/min) LABEL3:Ave. injection quantity (mm3/st) LABEL4:Max. var. bet. cyl. LABEL5:Remarks LABEL6:Distinguishing LABEL7:Governor set speed (r/min) LABEL8:Maximum no-load speed (r/min) LABEL9:Remarks (1)Adjustment conditions are the same as those for measuring injection quantity. (2)At high idle rack position L
----------
L=8.1mm
----------
a1=A a2=B a3=C a4=- r1=- r2=1100r/min r3=- r4=- Q1=- Q2=42.2+-1mm3/st Q3=- Q4=- c1=- c2=+-3.5% c3=- c4=- a5=32 a6=31 a7=30 a8=29 a9=28 a10=27 a11=26 a12=- a13=- a14=- a15=- r5=1600r/min r6=1550r/min r7=1500r/min r8=1450r/min r9=1400r/min r10=1350r/min r11=1300r/min r12=- r13=- r14=- r15=- R5=1720+-40r/min R6=1665+-38r/min R7=1610+-37r/min R8=1555+-36r/min R9=1505+-35r/min R10=1450+-33r/min R11=1395+-32r/min R12=- R13=- R14=- R15=-

Timing setting

Test data 101481-9370
(1)Pump vertical direction (2)Position of gear mark 'ZZ' at No 1 cylinder's beginning of injection (3)- (4)-
----------

----------
a=(100deg)




Have questions with 101481-9370?





Group cross 101481-9370 ZEXEL

Nissan-Diesel 

9 400 614 211 
1670001D01 
INJECTION-PUMP ASSEMBLY
FD35T
F 019 Z10 331 
 
INJECTION-PUMP ASSEMBLY

Nissan-Diesel 

9 400 614 212 
1670053T10 
INJECTION-PUMP ASSEMBLY
FD35T
 
 
INJECTION-PUMP ASSEMBLY
 
 
INJECTION-PUMP ASSEMBLY

Nissan-Diesel 

 
1679090305 
INJECTION-PUMP ASSEMBLY
FD35T04
9 400 614 213 
1670050T71 
INJECTION-PUMP ASSEMBLY
FD35T
9 400 619 545 
1670003D00 
INJECTION-PUMP ASSEMBLY
FD35T
F 019 Z10 332 
1670003D01 
INJECTION-PUMP ASSEMBLY
FD35T
9 400 614 214 
1670003D02 
INJECTION-PUMP ASSEMBLY
FD35T
 
1671290169 
INJECTION-PUMP ASSEMBLY
FD35T05
 
1671290171 
INJECTION-PUMP ASSEMBLY
BD30
9 400 614 215 
1671290179 
INJECTION-PUMP ASSEMBLY
BD30
101481-9370  

101481-9371 
 
1679090368 
INJECTION-PUMP ASSEMBLY
BD30
9 400 614 216 
1679090374 
INJECTION-PUMP ASSEMBLY
BD30
F 01G 09U 1JJ 
16712NA00D 
INJECTION-PUMP ASSEMBLY
BD30
Back to top