106873-3052 ZEXEL INJECTION-PUMP ASSEMBLY Calibration Data 1068733052 220801572a


106873-3052 INJECTION-PUMP ASSEMBLY
Rating:
50
Buy INJECTION-PUMP ASSEMBLY 106873-3052 zexel genuine, new aftermarket engine parts with delivery

Information injection-pump assembly

ZEXEL 106873-3052 1068733052
HINO 220801572A 220801572a

Cross reference number

ZEXEL 106873-3052 1068733052
HINO 220801572A 220801572a


Zexel num
Bosch num
Firm num
Name
106873-3052 
106873-3053 
 
220801572A  HINO
INJECTION-PUMP ASSEMBLY
F17E-B * K

Calibration Data:

Adjustment conditions
Test oil
1404 Test oil
  ISO4113 or {SAEJ967d}
Test oil temperature degC   40 40 45
Nozzle and nozzle holder   105780-8140
Bosch type code   EF8511/9A
Nozzle   105780-0000
Bosch type code   DN12SD12T
Nozzle holder   105780-2080
Bosch type code   EF8511/9
Opening pressure MPa   17.2
Opening pressure kgf/cm2   175
Injection pipe
Outer diameter - inner diameter - length (mm)
mm   8-3-600
Overflow valve   134424-0820
Overflow valve opening pressure kPa   127 107 147
Overflow valve opening pressure kgf/cm2   1.3 1.1 1.5
Tester oil delivery pressure kPa   157 157 157
Tester oil delivery pressure kgf/cm2   1.6 1.6 1.6
Direction of rotation (viewed from drive side)
Right
  R
Injection timing adjustment
Direction of rotation (viewed from drive side)
Right
  R
Injection order   1-8-6-2- 7-5-4-3
Pre-stroke mm   4.8 4.74 4.8
Beginning of injection position
Drive side
  NO.1
Difference between angles 1
Cal 1-8
deg.   45 44.75 45.25
Difference between angles 2
Cal 1-6
deg.   90 89.75 90.25
Difference between angles 3
Cyl.1-2
deg.   135 134.75 135.25
Difference between angles 4
Cal 1-7
deg.   180 179.75 180.25
Difference between angles 5
Cal 1-5
deg.   225 224.75 225.25
Difference between angles 6
Cal 1-4
deg.   270 269.75 270.25
Difference between angles 7
Cal 1-3
deg.   315 314.75 315.25
Injection quantity adjustment
Adjusting point   A
Rack position   8.9
Pump speed r/min   700 700 700
Average injection quantity mm3/st.   139.3 137.3 141.3
Max. variation between cylinders %   0 -2 2
Basic   *
Fixing the lever   *
Injection quantity adjustment_02
Adjusting point   B
Rack position   8.95+-0. 5
Pump speed r/min   1100 1100 1100
Average injection quantity mm3/st.   133.1 129.1 137.1
Fixing the lever   *
Injection quantity adjustment_03
Adjusting point   E
Rack position   3.8+-0.5
Pump speed r/min   225 225 225
Average injection quantity mm3/st.   10.4 7.4 13.4
Max. variation between cylinders %   0 -15 15
Fixing the rack   *
Injection quantity adjustment_04
Adjusting point   F
Rack position   -
Pump speed r/min   100 100 100
Average injection quantity mm3/st.   139 139
Fixing the lever   *
Remarks
After startup boost setting
 
Timer adjustment
Pump speed r/min   750--
Advance angle deg.   0 0 0
Load   1/4
Remarks
Start
 
Timer adjustment_02
Pump speed r/min   700
Advance angle deg.   0.3
Load   1/4
Timer adjustment_03
Pump speed r/min   820--
Advance angle deg.   0.7 0.4 1
Load   4/4
Timer adjustment_04
Pump speed r/min   900+50
Advance angle deg.   0.7 0.4 1
Load   3/4
Timer adjustment_05
Pump speed r/min   1100-50
Advance angle deg.   5.25 4.95 5.55
Load   4/4
Remarks
Finish
 

Test data Ex:

Governor adjustment

Test data 106873-3052
N:Pump speed R:Rack position (mm) (1)Tolerance for racks not indicated: +-0.05mm. (2)Set idle at point K (N = N1, R = R1) and confirm that the injection quantity does not exceed Q1 at point J (N = N2). (3)Excess fuel setting for starting: SXL (4)Damper spring setting (5)Variable speed specification: idling adjustment (6)Main spring setting
----------
N1=325r/min R1=3.8mm N2=1100rmin Q1=3mm3/st SXL=10.25+-0.1mm
----------

Speed control lever angle

Test data 106873-3052
F:Full speed I:Idle (1)Stopper bolt setting
----------

----------
a=(19deg)+-5deg b=19deg+-5deg

0000000901

Test data 106873-3052
F:Full load I:Idle (1)Use the hole at R = aa (2)Stopper bolt setting
----------
aa=42mm
----------
a=39deg+-5deg b=43.5deg+-3deg

Stop lever angle

Test data 106873-3052
N:Pump normal S:Stop the pump. (1)Rack position = aa (at delivery), set before governor adjustment (2)Set the stopper bolt (apply red paint). (3)Use the pin at R = bb (4)Lever free
----------
aa=12+-0.1mm bb=37mm
----------
a=(9deg)+-5deg b=9deg+-5deg c=35deg+-5deg

0000001501 LEVER

Test data 106873-3052
2-stage changeover lever adjustment (A) Speed lever (B) Load lever (C) 2-stage changeover lever (D) Link (E) Bolt (G) Variable speed specifications (H) Minimum maximum speed specifications F:Full speed I:Idle 1. Minimum-maximum speed specification adjustment (when running) (1)After completing governor adjustment, hold the 2-stage changeover lever (C) so that the speed lever (A) contacts the full speed stopper. (2)In this condition, the load lever is held in the idle position. (3)Adjust bolt (E) so that the clearance between the pin underneath lever (C) and the end of the long groove in link (D) is L. (4)Lock using the nut. 2. Variable speed specification adjustment (at operation) (1)Hold the 2-stage changeover lever (C) so that the load lever (B) contacts the full load stopper. (When the load lever is equipped with a cancel mechanism, move it so that it contacts the stopper without canceling.) (2)In this condition, confirm that the speed lever (A) moves from idle to full speed.
----------
L=1~2mm
----------

Timing setting

Test data 106873-3052
(1)Pump vertical direction (2)Coupling's key groove position at No 1 cylinder's beginning of injection (3)- (4)-
----------

----------
a=(80deg)




Have questions with 106873-3052?





Group cross 106873-3052 ZEXEL

Hino 

 
220801570A 
INJECTION-PUMP ASSEMBLY
F17E-B
 
220801571A 
INJECTION-PUMP ASSEMBLY
F17E-B
106873-3052  

106873-3053 
 
220801572A 
INJECTION-PUMP ASSEMBLY
F17E-B
 
 
INJECTION-PUMP ASSEMBLY

Hino 

 
220801573A 
INJECTION-PUMP ASSEMBLY
F17E-B
9 400 618 410 
220801573B 
INJECTION-PUMP ASSEMBLY
F17E-B
Back to top