104745-8231 ZEXEL 9 460 614 529 BOSCH INJECTION-PUMP ASSEMBLY 9460614529 1047458231 md334891


104745-8231 INJECTION-PUMP ASSEMBLY
Rating:
61
Buy INJECTION-PUMP ASSEMBLY 104745-8231 zexel genuine, new aftermarket engine parts with delivery

Information injection-pump assembly

BOSCH 9 460 614 529 9460614529
ZEXEL 104745-8231 1047458231
MITSUBISHI MD334891 md334891

Cross reference number

BOSCH 9 460 614 529 9460614529
ZEXEL 104745-8231 1047458231
MITSUBISHI MD334891 md334891


Zexel num
Bosch num
Firm num
Name
104745-8231 
9 460 614 529 
MD334891  MITSUBISHI
INJECTION-PUMP ASSEMBLY
4D56 K

Calibration Data:

Adjustment conditions
Test oil
1404 Test oil
  ISO4113orSAEJ967d
Test oil temperature degC   45 45 50
Nozzle   105780-0060
Bosch type code   NP-DN0SD1510
Nozzle holder   105780-2150
Opening pressure MPa   13 13 13.3
Opening pressure kgf/cm2   133 133 136
Injection pipe   157805-7320
Injection pipe
Inside diameter - outside diameter - length (mm)
mm   2-6-450
Joint assembly   157641-4720
Tube assembly   157641-4020
Transfer pump pressure kPa   20 20 20
Transfer pump pressure kgf/cm2   0.2 0.2 0.2
Direction of rotation (viewed from drive side)
Right
  R
Injection timing adjustment
Pump speed r/min   750 750 750
Boost pressure kPa   0 0 0
Boost pressure mmHg   0 0 0
Average injection quantity mm3/st.   50.6 50.1 51.1
Difference in delivery mm3/st.   4
Basic   *
Oil temperature degC   50 48 52
Remarks
NA
 
Injection timing adjustment_02
Pump speed r/min   750 750 750
Boost pressure kPa   33.3 32 34.6
Boost pressure mmHg   250 240 260
Average injection quantity mm3/st.   57 56.5 57.5
Difference in delivery mm3/st.   4.5
Basic   *
Oil temperature degC   50 48 52
Remarks
CBS
 
Injection timing adjustment_03
Pump speed r/min   1250 1250 1250
Boost pressure kPa   73.3 72 74.6
Boost pressure mmHg   550 540 560
Average injection quantity mm3/st.   65.9 65.4 66.4
Difference in delivery mm3/st.   5.5
Basic   *
Oil temperature degC   50 48 52
Remarks
Full
 
Injection timing adjustment_04
Pump speed r/min   750 750 750
Boost pressure kPa   0 0 0
Boost pressure mmHg   0 0 0
Average injection quantity mm3/st.   50.6 49.6 51.6
Basic   *
Oil temperature degC   50 48 52
Remarks
NA
 
Injection timing adjustment_05
Pump speed r/min   750 750 750
Boost pressure kPa   33.3 32 34.6
Boost pressure mmHg   250 240 260
Average injection quantity mm3/st.   57 56 58
Basic   *
Oil temperature degC   50 48 52
Remarks
CBS
 
Injection timing adjustment_06
Pump speed r/min   1000 1000 1000
Boost pressure kPa   73.3 72 74.6
Boost pressure mmHg   550 540 560
Average injection quantity mm3/st.   65.7 63.2 68.2
Oil temperature degC   50 48 52
Injection timing adjustment_07
Pump speed r/min   1250 1250 1250
Boost pressure kPa   73.3 72 74.6
Boost pressure mmHg   550 540 560
Average injection quantity mm3/st.   65.9 64.9 66.9
Difference in delivery mm3/st.   6
Basic   *
Oil temperature degC   50 48 52
Remarks
Full
 
Injection timing adjustment_08
Pump speed r/min   1750 1750 1750
Boost pressure kPa   73.3 72 74.6
Boost pressure mmHg   550 540 560
Average injection quantity mm3/st.   60 57.5 62.5
Oil temperature degC   50 48 52
Injection timing adjustment_09
Pump speed r/min   2100 2100 2100
Boost pressure kPa   73.3 72 74.6
Boost pressure mmHg   550 540 560
Average injection quantity mm3/st.   53.7 51.2 56.2
Oil temperature degC   52 50 54
Injection quantity adjustment
Pump speed r/min   2650 2650 2650
Boost pressure kPa   73.3 72 74.6
Boost pressure mmHg   550 540 560
Average injection quantity mm3/st.   27.9 24.9 30.9
Difference in delivery mm3/st.   8.5
Basic   *
Oil temperature degC   55 52 58
Injection quantity adjustment_02
Pump speed r/min   3050 3050 3050
Boost pressure kPa   73.3 72 74.6
Boost pressure mmHg   550 540 560
Average injection quantity mm3/st.   5
Oil temperature degC   55 52 58
Injection quantity adjustment_03
Pump speed r/min   2650 2650 2650
Boost pressure kPa   73.3 72 74.6
Boost pressure mmHg   550 540 560
Average injection quantity mm3/st.   27.9 22.9 32.9
Difference in delivery mm3/st.   9
Basic   *
Oil temperature degC   55 52 58
Governor adjustment
Pump speed r/min   375 375 375
Boost pressure kPa   0 0 0
Boost pressure mmHg   0 0 0
Average injection quantity mm3/st.   16.4 14.9 17.9
Difference in delivery mm3/st.   2
Basic   *
Oil temperature degC   48 46 50
Governor adjustment_02
Pump speed r/min   375 375 375
Boost pressure kPa   0 0 0
Boost pressure mmHg   0 0 0
Average injection quantity mm3/st.   16.4 14.4 18.4
Difference in delivery mm3/st.   2.5
Basic   *
Oil temperature degC   48 46 50
Governor adjustment_03
Pump speed r/min   750 750 750
Boost pressure kPa   0 0 0
Boost pressure mmHg   0 0 0
Average injection quantity mm3/st.   5
Oil temperature degC   50 48 52
Boost compensator adjustment
Pump speed r/min   900 900 900
Boost pressure kPa   0 0 0
Boost pressure mmHg   0 0 0
Oil temperature degC   50 48 52
Lever angle (shim thickness) mm   9.4 9.4 9.4
Remarks
MEASURE
 
Timer adjustment
Pump speed r/min   100 100 100
Boost pressure kPa   0 0 0
Boost pressure mmHg   0 0 0
Average injection quantity mm3/st.   75 65 85
Basic   *
Oil temperature degC   48 46 50
Remarks
IDLE
 
Timer adjustment_02
Pump speed r/min   100 100 100
Boost pressure kPa   0 0 0
Boost pressure mmHg   0 0 0
Average injection quantity mm3/st.   75 65 85
Oil temperature degC   48 46 50
Remarks
IDLE
 
Speed control lever angle
Pump speed r/min   375 375 375
Boost pressure kPa   0 0 0
Boost pressure mmHg   0 0 0
Average injection quantity mm3/st.   0 0 0
Oil temperature degC   48 46 50
Remarks
Magnet OFF at idling position
 
0000000901
Pump speed r/min   1250 1250 1250
Boost pressure kPa   73.3 72 74.6
Boost pressure mmHg   550 540 560
Overflow quantity cm3/min   420 290 550
Oil temperature degC   50 48 52
Stop lever angle
Pump speed r/min   1250 1250 1250
Boost pressure kPa   73.3 72 74.6
Boost pressure mmHg   550 540 560
Pressure kPa   549 520 578
Pressure kgf/cm2   5.6 5.3 5.9
Basic   *
Oil temperature degC   50 48 52
0000001101
Pump speed r/min   1250 1250 1250
Boost pressure kPa   73.3 72 74.6
Boost pressure mmHg   550 540 560
Timer stroke mm   4.6 4.4 4.8
Basic   *
Oil temperature degC   50 48 52
_02
Pump speed r/min   500 500 500
Boost pressure kPa   73.3 72 74.6
Boost pressure mmHg   550 540 560
Timer stroke mm   1.2 0.6 1.8
Oil temperature degC   48 46 50
_03
Pump speed r/min   1000 1000 1000
Boost pressure kPa   73.3 72 74.6
Boost pressure mmHg   550 540 560
Timer stroke mm   3.5 2.9 4.1
Oil temperature degC   50 48 52
_04
Pump speed r/min   1250 1250 1250
Boost pressure kPa   73.3 72 74.6
Boost pressure mmHg   550 540 560
Timer stroke mm   4.6 4.2 5
Basic   *
Oil temperature degC   50 48 52
_05
Pump speed r/min   1500 1500 1500
Boost pressure kPa   73.3 72 74.6
Boost pressure mmHg   550 540 560
Timer stroke mm   5.6 5 6.2
Oil temperature degC   50 48 52
_06
Pump speed r/min   2100 2100 2100
Boost pressure kPa   73.3 72 74.6
Boost pressure mmHg   550 540 560
Timer stroke mm   7.8 7.2 8.4
Oil temperature degC   52 50 54
0000001201
Max. applied voltage V   8 8 8
Test voltage V   13 12 14
0000001401
Pump speed r/min   1250 1250 1250
Boost pressure kPa   73.3 72 74.6
Boost pressure mmHg   550 540 560
Average injection quantity mm3/st.   48 47.5 48.5
Timer stroke TA mm   3.9 3.7 4.1
Timer stroke variation dT mm   0.7 0.7 0.7
Basic   *
Oil temperature degC   50 48 52
_02
Pump speed r/min   1250 1250 1250
Boost pressure kPa   73.3 72 74.6
Boost pressure mmHg   550 540 560
Average injection quantity mm3/st.   48 47 49
Timer stroke TA mm   3.9 3.5 4.3
Basic   *
Oil temperature degC   50 48 52
_03
Pump speed r/min   1250 1250 1250
Boost pressure kPa   73.3 72 74.6
Boost pressure mmHg   550 540 560
Average injection quantity mm3/st.   32 31 33
Timer stroke TA mm   2.5 1.9 3.1
Oil temperature degC   50 48 52
Timing setting
K dimension mm   3.3 3.2 3.4
KF dimension mm   5.8 5.7 5.9
MS dimension mm   1.4 1.3 1.5
BCS stroke mm   3.2 3 3.4
Control lever angle alpha deg.   59 55 63
Control lever angle beta deg.   41 36 46

Test data Ex:

0000001801 W-CSD ADJUSTMENT

Test data 104745-8231
Adjustment of the W-CSD 1. Adjustment of the advance angle of the timer (1)Determine the timer advance angle using the following graph. (2)(1) Adjust with the screw (A) so that the timer advance angle determined in the item (1) is obtained. X:Temperature t (deg C) Y:Timer stroke TA (mm) (B): Timer stroke TA (mm):
----------

----------
(C)=TA=-0.0526t+3.14(-3<=t)

0000001901 W-FICD LEVER ADJUSTMENT

Test data 104745-8231
2. Adjustment of the W-FICD (1)Insert a block gauge L determined from the graph below between the control lever (D) and the idling stopper bolt (C). (2)Insert a shim S between the W-FICD lever (E) and the control lever (F). Adjust the W-FICD lever (E) so that it contacts the control lever (F) and fix it using bolt (B). TT Note: a) The temperature of wax at the time of adjustment must not exceed a. b) After completion of the adjustment, confirm that allowance for adjustment of the screw (G) is at least L1. Y:Control lever L mm X:Temperature t (deg C) H:Control lever gap: L (mm)
----------
L=L+-0.05mm S=5+-0.05mm T=3.4~4.9N-m(0.35~0.5kgf-m) a=30degC L1=3mm
----------
S=5mm L1=3mm H=L=-0.256t+10.39(-3<=tdegC)(S=5+-0.05mm)

0000002001 V-FICD ADJUSTMENT

Test data 104745-8231
Adjustment of the two stage actuator (FICD). (B): Stroke adjusting nut (C): Actuator stroke (D): Nut for adjusting the position of the rod X:Injection quantity (mm3/st) Y:Thickness of the shim = L (mm) 1. Selecting the shim for adjusting the actuator. (1)Insert the shim L1 between the control lever and the idling stopper bolts at N; then measure the injection quantity. (2)Select the thickness L of the shim for adjusting the actuator utilizing the following formula (refer to the graph). Calculation: L+-0.01 = -0.3348Q+11.972mm(4.0<=Q<=16.0mm3/st) 2. Adjustment of the actuator (1)Mount the actuator to the injection pump. (2)Position the control lever in the idling position. (3)Adjust with the nut (D) so that the space between the control lever and the rod is L2. (4)Insert the shim L determined above between the control lever and the idling stopper bolt. (5)Adjust the position of screw (A) so that the actuator moves through its full stroke (reference: approx. L3), then fix using nut (B). (6)Allowable angle when adjusting the rod position: c
----------
N=900(r/min) L1=9.4(mm) L2=1+1(mm) L3=9.6(mm) c=+-20(deg)
----------
L2=1+1(mm) SW1=SW7 SW2=SW8 T1=1.4~2(N-m)(0.14~0.2(kgf-m)) T2=3.5~5(N-m)(0.35~0.5(kgf-m)) a=20(deg) b=20(deg)




Have questions with 104745-8231?





Group cross 104745-8231 ZEXEL

9 460 611 140 
 
INJECTION-PUMP ASSEMBLY

Mitsubishi 

9 460 611 613 
MD334888 
INJECTION-PUMP ASSEMBLY
4D56
9 460 611 141 
 
INJECTION-PUMP ASSEMBLY

Mitsubishi 

9 460 612 414 
MD334889 
INJECTION-PUMP ASSEMBLY
4D56
9 460 611 743 
 
INJECTION-PUMP ASSEMBLY

Mitsubishi 

9 460 614 528 
MD334890 
INJECTION-PUMP ASSEMBLY
4D56
9 460 611 744 
 
INJECTION-PUMP ASSEMBLY

Mitsubishi 

104745-8231  
9 460 614 529 
MD334891 
INJECTION-PUMP ASSEMBLY
4D56
9 460 611 016 
 
INJECTION-PUMP ASSEMBLY

Mitsubishi 

9 460 612 415 
MD334892 
INJECTION-PUMP ASSEMBLY
4D56
9 460 611 745 
 
INJECTION-PUMP ASSEMBLY

Mitsubishi 

9 460 614 530 
MD334893 
INJECTION-PUMP ASSEMBLY
4D56
9 460 611 746 
 
INJECTION-PUMP ASSEMBLY

Mitsubishi 

9 460 613 499 
MD334894 
INJECTION-PUMP ASSEMBLY
4D56
9 460 611 747 
 
INJECTION-PUMP ASSEMBLY

Mitsubishi 

9 460 614 531 
MD334895 
INJECTION-PUMP ASSEMBLY
4D56
9 460 611 748 
MD334896 
INJECTION-PUMP ASSEMBLY
4D56
9 460 611 017 
MD334897 
INJECTION-PUMP ASSEMBLY
4D56
Back to top