101603-8401 ZEXEL INJECTION-PUMP ASSEMBLY Calibration Data 1016038401 8943955721


101603-8401 INJECTION-PUMP ASSEMBLY
Rating:
17
Buy INJECTION-PUMP ASSEMBLY 101603-8401 zexel genuine, new aftermarket engine parts with delivery

Information injection-pump assembly

ZEXEL 101603-8401 1016038401
ISUZU 8943955721 8943955721

Cross reference number

ZEXEL 101603-8401 1016038401
ISUZU 8943955721 8943955721


Zexel num
Bosch num
Firm num
Name
101603-8401 
101603-8402 
 
8943955721  ISUZU
INJECTION-PUMP ASSEMBLY
6HH1-S * K

Calibration Data:

Adjustment conditions
Test oil
1404 Test oil
  ISO4113 or {SAEJ967d}
Test oil temperature degC   40 40 45
Nozzle and nozzle holder   105780-8140
Bosch type code   EF8511/9A
Nozzle   105780-0000
Bosch type code   DN12SD12T
Nozzle holder   105780-2080
Bosch type code   EF8511/9
Opening pressure MPa   17.2
Opening pressure kgf/cm2   175
Injection pipe
Outer diameter - inner diameter - length (mm)
mm   6-2-600
Overflow valve   131424-4920
Overflow valve opening pressure kPa   127 107 147
Overflow valve opening pressure kgf/cm2   1.3 1.1 1.5
Tester oil delivery pressure kPa   157 157 157
Tester oil delivery pressure kgf/cm2   1.6 1.6 1.6
Direction of rotation (viewed from drive side)
Left
  L
Injection timing adjustment
Direction of rotation (viewed from drive side)
Left
  L
Injection order   1-5-3-6- 2-4
Pre-stroke mm   4.7 4.65 4.75
Rack position
After adjusting injection quantity.
  R=A
Beginning of injection position
Governor side
  NO.1
Difference between angles 1
Cal 1-5
deg.   60 59.5 60.5
Difference between angles 2
Cal 1-3
deg.   120 119.5 120.5
Difference between angles 3
Cal 1-6
deg.   180 179.5 180.5
Difference between angles 4
Cyl.1-2
deg.   240 239.5 240.5
Difference between angles 5
Cal 1-4
deg.   300 299.5 300.5
Injection quantity adjustment
Adjusting point   -
Rack position   13
Pump speed r/min   850 850 850
Average injection quantity mm3/st.   86.5 84.9 88.1
Max. variation between cylinders %   0 -2.5 2.5
Basic   *
Fixing the rack   *
Standard for adjustment of the maximum variation between cylinders   *
Injection quantity adjustment_02
Adjusting point   -
Rack position   9.6+-0.5
Pump speed r/min   275 275 275
Average injection quantity mm3/st.   9.4 8.1 10.7
Max. variation between cylinders %   0 -14 14
Fixing the rack   *
Standard for adjustment of the maximum variation between cylinders   *
Remarks
Adjust only variation between cylinders; adjust governor according to governor specifications.
 
Injection quantity adjustment_03
Adjusting point   A
Rack position   R1(13)
Pump speed r/min   850 850 850
Average injection quantity mm3/st.   86.5 85.5 87.5
Basic   *
Fixing the lever   *
Injection quantity adjustment_04
Adjusting point   B
Rack position   R1+0.15
Pump speed r/min   1450 1450 1450
Average injection quantity mm3/st.   95.5 92.3 98.7
Fixing the lever   *
Injection quantity adjustment_05
Adjusting point   C
Rack position   R1-0.25
Pump speed r/min   600 600 600
Average injection quantity mm3/st.   77.5 74.3 80.7
Fixing the lever   *
Timer adjustment
Pump speed r/min   905--
Advance angle deg.   0 0 0
Load   3/5
Remarks
Start
 
Timer adjustment_02
Pump speed r/min   855
Advance angle deg.   0.3
Load   3/5
Timer adjustment_03
Pump speed r/min   1110
Advance angle deg.   1.5 1 2
Load   3/5
Timer adjustment_04
Pump speed r/min   -
Advance angle deg.   1.5 1 2
Load   5/5
Remarks
Measure the actual speed.
 
Timer adjustment_05
Pump speed r/min   1450
Advance angle deg.   7 6.5 7.5
Load   5/5
Remarks
Finish
 

Test data Ex:

Governor adjustment

Test data 101603-8401
N:Pump speed R:Rack position (mm) (1)Torque cam stamping: T1 (2)Tolerance for racks not indicated: +-0.05mm. (3)Air cylinder operating pressure: P1 or more (4)Air cylinder operating pressure: P2
----------
T1=K09 P1=294kPa(3kgf/cm2) P2=0kPa(0kgf/cm2)
----------

Speed control lever angle

Test data 101603-8401
F:Full speed I:Idle (1)When air cylinder OFF. (2)Air cylinder operating pressure: at P1 (3)Use the pin at R = aa (4)Stopper bolt set position 'H'
----------
P1=294kPa(3kgf/cm2) aa=35mm
----------
a=10deg+-5deg b=40deg+-3deg c=(35deg)+-3deg

Stop lever angle

Test data 101603-8401
N:Pump normal S:Stop the pump. (1)Use the pin at R = aa
----------
aa=45mm
----------
a=12.5deg+-5deg b=40deg+-5deg

0000001501 I/P WITH LOAD PLUNGER ADJ

Plunger assembly number: PL (stamping: ST) 1. Adjustment procedures (1)Insert the pre-stroke adjusting shims L1 for each cylinder. (2)Adjust injection quantity.(max. var. bet. cyl. idling a1, full a2) (3)At basic point A, adjust so that the pre-stroke is L2. (4)Reconfirm the injection quantity.
----------
PL=131153-9020 ST=A769 L1=1mm L2=4.7+-0.05mm a1=+-14% a2=+-2.5%
----------

0000001601 AIR CYLINDER

Test data 101603-8401
(A): Speed lever (B): Speed lever (a): Stopper bolt (b): Nut 1. Air cylinder adjustment procedure (1)Apply positive pressure P1 (ON) to the air cylinder. (2)Operate the speed lever (A). (At this time speed lever (B) also moves together.) (3)At speed N1 and rack position Ra, adjust using stopper bolt (b) so that speed lever (B) is at the stop position and speed lever (A) is in the cancel position. (4)Confirm that the speed lever turns to the full position at positive pressure (OFF) P2. (5)After repeating the above several times, fix the stopper bolt (a) using the nut (b).
----------
P1=294kPa(3kgf/cm2) P2=0kPa(0kgf/cm2) N1=1450r/min Ra=12+-0.1mm
----------

Timing setting

Test data 101603-8401
(1)Pump vertical direction (2)Position of timer's threaded hole at No 1 cylinder's beginning of injection (3)B.T.D.C.: aa (4)-
----------
aa=6deg
----------
a=(150deg)




Have questions with 101603-8401?





Group cross 101603-8401 ZEXEL

Isuzu 

 
8943955720 
INJECTION-PUMP ASSEMBLY
6HH1-S
101603-8401  

101603-8402 
 
8943955721 
INJECTION-PUMP ASSEMBLY
6HH1-S
 
8943955722 
INJECTION-PUMP ASSEMBLY
6HH1-S
9 400 615 263 
8943955723 
INJECTION-PUMP ASSEMBLY
6HH1-S
 
8943955210 
INJECTION-PUMP ASSEMBLY
6HH1-S
 
8943955212 
INJECTION-PUMP ASSEMBLY
6HH1-S
 
8943955213 
INJECTION-PUMP ASSEMBLY
6HH1-S
 
8943901630 
INJECTION-PUMP ASSEMBLY
6HH1-S
9 400 615 264 
8943901631 
INJECTION-PUMP ASSEMBLY
6HH1-S
 
8943955220 
INJECTION-PUMP ASSEMBLY
6HH1-S
 
8943955222 
INJECTION-PUMP ASSEMBLY
6HH1-S
 
8943955223 
INJECTION-PUMP ASSEMBLY
6HH1-S
 
8943901640 
INJECTION-PUMP ASSEMBLY
6HH1-S
9 400 615 265 
8943901641 
INJECTION-PUMP ASSEMBLY
6HH1-S
9 400 615 266 
1156029660 
INJECTION-PUMP ASSEMBLY
6SA1-T
9 400 610 657 
8943955821 
INJECTION-PUMP ASSEMBLY
6HH1-N
9 400 615 267 
8943956451 
INJECTION-PUMP ASSEMBLY
6HH1-N
9 400 612 770 
8943956461 
INJECTION-PUMP ASSEMBLY
6HH1-N
F 019 Z10 114 
8943957490 
INJECTION-PUMP ASSEMBLY
6HH1-S
 
8943957491 
INJECTION-PUMP ASSEMBLY
6HH1-S
 
8943957492 
INJECTION-PUMP ASSEMBLY
6HH1-S
9 400 615 268 
8943957493 
INJECTION-PUMP ASSEMBLY
6HH1-S
 
8943957500 
INJECTION-PUMP ASSEMBLY
6HH1-S
 
8943957501 
INJECTION-PUMP ASSEMBLY
6HH1-S
9 400 610 658 
8943957502 
INJECTION-PUMP ASSEMBLY
6HH1-S
F 01G 09U 049 
8943957503 
INJECTION-PUMP ASSEMBLY
6HH1-S
 
8943957510 
INJECTION-PUMP ASSEMBLY
6HH1-S
9 400 619 950 
8943957511 
INJECTION-PUMP ASSEMBLY
6HH1-S
 
8943957512 
INJECTION-PUMP ASSEMBLY
6HH1-S
9 400 615 269 
8943957513 
INJECTION-PUMP ASSEMBLY
6HH1-S
Back to top