Information nozzle-holder
BOSCH
9 430 615 041
9430615041
ZEXEL
105048-3070
1050483070
MITSUBISHI
ME017846
me017846
Rating:
Scheme ###:
2. | [2] | 150508-5900 | BEARING PIN |
4. | [1] | 150515-9900 | SLOTTED WASHER |
6. | [1] | 150562-4300 | COMPRESSION SPRING |
13. | [1] | 150524-4200 | SPACER BUSHING |
20. | [1] | 150655-0000 | NOZZLE-RETAINING NUT |
800S/1. | [1] | 150591-1000 | SHIM D7.2&3.6T0.10 |
800S/1. | [1] | 150591-2000 | SHIM D7.2&3.6T0.20 |
800S/1. | [1] | 150591-3000 | SHIM D7.2&3.6T0.30 |
800S/1. | [1] | 150591-4000 | SHIM D7.2&3.6T0.40 |
800S/1. | [1] | 150591-5000 | SHIM D7.2&3.6T0.50 |
800S/1. | [1] | 150591-5100 | SHIM D7.2&3.6T0.51 |
800S/1. | [1] | 150591-5200 | SHIM D7.2&3.6T0.52 |
800S/1. | [1] | 150591-5300 | SHIM D7.2&3.6T0.53 |
800S/1. | [1] | 150591-5400 | SHIM D7.2&3.6T0.54 |
800S/1. | [1] | 150591-5500 | SHIM D7.2&3.6T0.55 |
800S/1. | [1] | 150591-5600 | SHIM D7.2&3.6T0.56 |
800S/1. | [1] | 150591-5700 | SHIM D7.2&3.6T0.57 |
800S/1. | [1] | 150591-5800 | SHIM D7.2&3.6T0.58 |
800S/1. | [1] | 150591-5900 | SHIM D7.2&3.6T0.59 |
Include in #1:
101401-1063
as NOZZLE-HOLDER
Cross reference number
Zexel num
Bosch num
Firm num
Name
105048-3070
9 430 615 041
ME017846 MITSUBISHI
NOZZLE-HOLDER
K 53LZ NOZZLE HOLDER NH NH
K 53LZ NOZZLE HOLDER NH NH
Information:
Start By:a. remove radiator
Keep all parts clean from contaminants. Contaminants put into the system may cause rapid wear and shortened component life.
1. Loosen bolt (4), bolt (5), and bolt (6). Remove belts (3).2. Remove bolts (2) and fan (1). 3. Remove bolt (7) and washer (8). Put enough spacers (10) on bolt (7) to get approximately 3.18 mm (.125 in) of clearance between washer (8) and vibration damper and pulley assembly (9). Install bolt (7), washer (8), and spacers (10).
If spacers (10) are not used, damage to the bolt and/or crankshaft can result when the vibration damper and pulley are removed from the crankshaft.
4. Install tool (A) as shown, and loosen vibration damper and pulley assembly (9).5. Remove tool (A), bolt (7), washer (8), spacers (10), and vibration damper and pulley assembly (9). 6. If necessary, remove bolts (11) and vibration damper (12). The following steps are to install the crankshaft vibration damper and pulley. Inspect the vibration damper housing for leakage or dents (damage housing). If either condition exists, a replacement of the vibration damper must be made.7. Install vibration damper (12) on pulley (13). Install bolts (11).8. Install vibration damper and pulley assembly (9) and install bolt (7), spacers (10) and washer (8).
The flat side of washer (8) must be installed toward vibration damper and pulley assembly (9).
9. Tighten bolt (7) to a torque of 284 to 340 N m (210 to 250 lb ft). Hit bolt (7) with a hammer and retighten to a torque of 284 to 340 N m (210 to 250 lb ft).10. Position belts (3). Tighten bolts (4), (5), and (6). Use a belt tension gauge and make an adjustment of the belts. Measure the belt farthest from the engine. Tighten new belts until the gauge indication is 534 22 N (120 5 lb ft). Operate the engine at high idle for a minimum of 30 minutes after installing radiator and guards. Make another adjustment of the belt tension. The correct gauge indication for a used belt is 400 44 N (90 10 lb.). Tighten bolt (4), bolt (5), and bolt (6).11. Install fan (1) and bolt (2).End By:a. install radiator
Perform Scheduled Oil Sampling on oil wetted compartments after performing service work to check for contaminants left in the system following repair. Contaminants put into the system may cause rapid wear and shortened component life.
Keep all parts clean from contaminants. Contaminants put into the system may cause rapid wear and shortened component life.
1. Loosen bolt (4), bolt (5), and bolt (6). Remove belts (3).2. Remove bolts (2) and fan (1). 3. Remove bolt (7) and washer (8). Put enough spacers (10) on bolt (7) to get approximately 3.18 mm (.125 in) of clearance between washer (8) and vibration damper and pulley assembly (9). Install bolt (7), washer (8), and spacers (10).
If spacers (10) are not used, damage to the bolt and/or crankshaft can result when the vibration damper and pulley are removed from the crankshaft.
4. Install tool (A) as shown, and loosen vibration damper and pulley assembly (9).5. Remove tool (A), bolt (7), washer (8), spacers (10), and vibration damper and pulley assembly (9). 6. If necessary, remove bolts (11) and vibration damper (12). The following steps are to install the crankshaft vibration damper and pulley. Inspect the vibration damper housing for leakage or dents (damage housing). If either condition exists, a replacement of the vibration damper must be made.7. Install vibration damper (12) on pulley (13). Install bolts (11).8. Install vibration damper and pulley assembly (9) and install bolt (7), spacers (10) and washer (8).
The flat side of washer (8) must be installed toward vibration damper and pulley assembly (9).
9. Tighten bolt (7) to a torque of 284 to 340 N m (210 to 250 lb ft). Hit bolt (7) with a hammer and retighten to a torque of 284 to 340 N m (210 to 250 lb ft).10. Position belts (3). Tighten bolts (4), (5), and (6). Use a belt tension gauge and make an adjustment of the belts. Measure the belt farthest from the engine. Tighten new belts until the gauge indication is 534 22 N (120 5 lb ft). Operate the engine at high idle for a minimum of 30 minutes after installing radiator and guards. Make another adjustment of the belt tension. The correct gauge indication for a used belt is 400 44 N (90 10 lb.). Tighten bolt (4), bolt (5), and bolt (6).11. Install fan (1) and bolt (2).End By:a. install radiator
Perform Scheduled Oil Sampling on oil wetted compartments after performing service work to check for contaminants left in the system following repair. Contaminants put into the system may cause rapid wear and shortened component life.
Have questions with 105048-3070?
Group cross 105048-3070 ZEXEL
Mitsubishi
Isuzu
Mitsubishi
Mazda
Komatsu
Mitsubishi
105048-3070
9 430 615 041
ME017846
NOZZLE-HOLDER