105048-3050 ZEXEL 9 430 615 030 BOSCH NOZZLE-HOLDER 9430615030 1050483050 sl0113660


 

Information nozzle-holder

BOSCH 9 430 615 030 9430615030
ZEXEL 105048-3050 1050483050
MAZDA SL0113660 sl0113660
105048-3050 NOZZLE-HOLDER
Rating:
52
Buy NOZZLE-HOLDER 105048-3050 zexel genuine, new aftermarket engine parts with delivery

Scheme ###:

2. [2] 150508-5900 BEARING PIN
4. [1] 150515-9900 SLOTTED WASHER
6. [1] 150562-4300 COMPRESSION SPRING
13. [1] 150524-4200 SPACER BUSHING
20. [1] 150655-0000 NOZZLE-RETAINING NUT
800S/1. [0] 150534-3600 SHIM
800S/1. [0] 150534-3700 SHIM
800S/1. [0] 150534-3800 SHIM
800S/1. [0] 150534-3900 SHIM
800S/1. [0] 150534-4000 SHIM
800S/1. [0] 150534-4100 SHIM
800S/1. [0] 150534-4200 SHIM
800S/1. [0] 150534-4300 SHIM
800S/1. [0] 150534-4400 SHIM

Cross reference number

Zexel num
Bosch num
Firm num
Name
105048-3050 
105048-3121 
9 430 615 030 
SL0113660  MAZDA
NOZZLE-HOLDER
* K 53LZ NH NH




Information:


Keep all parts clean from contaminants. Contaminants put into the system may cause rapid wear and shortened component life.
1. Remove the carbon ring and lip from the inner surface of the cylinder liner. 2. Turn the crankshaft until two of the pistons are at bottom center. Remove the nuts and bolts (1) from the connecting rods that are at bottom center. Remove connecting rod caps (2), and put identification marks on them for installation purposes.
Do not let the connecting rods hit the crankshaft or the bottom edge of the cylinder liners when the pistons are removed.
3. Push the connecting rods and pistons away from the crankshaft until the piston rings are out of the cylinder liners. Remove the two pistons from the engine.4. Keep each connecting rod cap with its respective connecting rod and piston. Put identification marks on each piston as to its location in the engine.5. Do Steps 1 through 4 for the removal of the remaining pistons.Install Pistons And Connecting Rods
1. Turn the crankshaft until the bearing journals for the pistons to be installed are at bottom center.2. Put clean engine oil on the crankshaft journals and on the inside of the cylinder liners. Put clean engine oil on the piston rings and the connecting rod bearings.3. Move the piston rings on the pistons until the ring openings are approximately 90° apart. 4. Put the piston in the cylinder liner with the "V" mark on the piston in alignment with the "V" mark on the cylinder block. Put tooling (A) in position on the cylinder block and compress the piston rings.5. Push the piston into the cylinder liner and out of the ring compressor. 6. Pull the connecting rod into position on the crankshaft as shown. Install connecting rod bolts (1) in the connecting rods.7. Put clean engine oil on the lower half of the connecting rod bearing. Put 2P2506 Thread Lubricant on the bolt threads and on the surfaces of the nuts that make contact with the rod caps.
When the connecting rod caps are installed, make sure the number on the side of the cap is next to and respective with the number on the side of the connecting rod.
8. Install connecting rod caps (2) and the nuts that hold them. Tighten the nuts to a torque of 41 4 N m (30 3 lb ft). Put a mark on each nut as to its location, and tighten them 90° 5° more.9. Perform Steps 1 through 8 for the remainder of the pistons.End By:a. install oil pumpb. install oil pan platec. install spacer plate
Perform Scheduled Oil Sampling on oil wetted compartments after performing service work to check for contaminants left in the system following repair. Contaminants put into the system may cause rapid wear and shortened component life.
Disassemble Pistons And Connecting Rods
Start By:a. remove pistons and connecting rods
Keep all parts clean from contaminants. Contaminants put into the system may cause rapid wear and shortened component life.
1. Remove the rings from the

Have questions with 105048-3050?





Group cross 105048-3050 ZEXEL

Mitsubishi 

9 430 615 275 
ME016542 
NOZZLE-HOLDER
9 430 615 142 
ME019733 
NOZZLE-HOLDER

Isuzu 

9 430 616 028 
8941222630 
NOZZLE-HOLDER
9 430 615 074 
8941222631 
NOZZLE-HOLDER
9 430 615 817 
8941222632 
NOZZLE-HOLDER
9 430 615 817 
8972103860 
NOZZLE-HOLDER
9 430 616 029 
8941394650 
NOZZLE-HOLDER
9 430 615 054 
8941394651 
NOZZLE-HOLDER
9 430 615 818 
8941394652 
NOZZLE-HOLDER

Mitsubishi 

9 430 616 030 
ME017845 
NOZZLE-HOLDER

Mazda 

105048-3050  

105048-3121 
9 430 615 030 
SL0113660 
NOZZLE-HOLDER

Komatsu 

9 430 615 058 
6207113110 
NOZZLE-HOLDER
9 430 615 058 
6207113060 
NOZZLE-HOLDER

Mitsubishi 

9 430 615 041 
ME017846 
NOZZLE-HOLDER

Isuzu 

9 430 616 031 
8941609570 
NOZZLE-HOLDER

Iseki 

 
62153300010 
NOZZLE-HOLDER
9 430 615 819 
62153300011 
NOZZLE-HOLDER
Back to top