108922-2050 ZEXEL 9 400 619 402 BOSCH INJECTION-PUMP ASSEMBLY 9400619402 1089222050 me094336

Information Cross number Calibration Data Calibration Data Ex

Price: query
Buy now
Add to cart Go to cart

Rating:

Buy INJECTION-PUMP ASSEMBLY 108922-2050 zexel genuine, new aftermarket engine parts with delivery

Information injection-pump assembly

BOSCH 9 400 619 402 9400619402

ZEXEL 108922-2050 1089222050

MITSUBISHI ME094336 me094336

Service parts 108922-2050 INJECTION-PUMP ASSEMBLY:

1. _

2. FUEL INJECTION PUMP 108092-0032

3. GOVERNOR 105952-1560

4. SUPPLY PUMP 105237-4810

5. AUTOM. ADVANCE MECHANIS

6. COUPLING PLATE 105664-2270

7. COUPLING PLATE

8. _ 159600-4121

9. _ 156640-1320

10. NOZZLE AND HOLDER ASSY 105110-7333

11. Nozzle and Holder ME093528

12. Open Pre:MPa(Kqf/cm2)

13. NOZZLE-HOLDER 105041-4121

14. NOZZLE

15. NOZZLE SET 105019-0510

Include in #1:

108922-2050 as INJECTION-PUMP ASSEMBLY

Cross reference number

BOSCH 9 400 619 402 9400619402

ZEXEL 108922-2050 1089222050

MITSUBISHI ME094336 me094336

Zexel num

Bosch num

Firm num

Name

108922-2050
108922-2080

9 400 619 402

ME094336 MITSUBISHI

INJECTION-PUMP ASSEMBLY
10DC9T2 K 14CR INJECTION PUMP ASSY TICS HD-TI10F TICS

Calibration Data:

Adjustment conditions

Test oil
1404 Test oil ISO4113 or {SAEJ967d}

Test oil temperature degC 40 40 45

Nozzle and nozzle holder 105780-8250

Bosch type code 1 688 901 101

Nozzle 105780-0120

Bosch type code 1 688 901 990

Nozzle holder 105780-2190

Opening pressure MPa 20.7

Opening pressure kgf/cm2 211

Injection pipe
Outer diameter - inner diameter - length (mm) mm 8-3-600

Overflow valve 131425-0220

Overflow valve opening pressure kPa 157 123 191

Overflow valve opening pressure kgf/cm2 1.6 1.25 1.95

Tester oil delivery pressure kPa 255 255 255

Tester oil delivery pressure kgf/cm2 2.6 2.6 2.6

RED3 control unit part number 407910-3 960

RED3 rack sensor specifications mm 19

PS/ACT control unit part no. 407980-2 24*

Digi switch no. 52

Direction of rotation (viewed from drive side)
Right R

Injection timing adjustment

Direction of rotation (viewed from drive side)
Right R

Injection order 1-2-7-8- 5-6-3-4- 9-10

Pre-stroke mm 8.5 8.47 8.53

Beginning of injection position
Governor side NO.1

Difference between angles 1
Cyl.1-2 deg. 45 44.75 45.25

Difference between angles 2
Cal 1-7 deg. 72 71.75 72.25

Difference between angles 3
Cal 1-8 deg. 117 116.75 117.25

Difference between angles 4
Cal 1-5 deg. 144 143.75 144.25

Difference between angles 5
Cal 1-6 deg. 189 188.75 189.25

Difference between angles 6
Cal 1-3 deg. 216 215.75 216.25

Difference between angles 7
Cal 1-4 deg. 261 260.75 261.25

Difference between angles 8
Cal 1-9 deg. 288 287.75 288.25

Difference between angles 9
Cal 1-10 deg. 333 332.75 333.25

Injection quantity adjustment

Rack position (11.2)

Vist V 2.18 2.18 2.18

Pump speed r/min 650 650 650

Average injection quantity mm3/st. 128.5 127.5 129.5

Max. variation between cylinders % 0 -3 3

Basic *

PS407980-224* V 2.45+-0. 01

PS407980-224* mm 6.1+-0.0 5

Injection quantity adjustment_02

Rack position (6.8)

Vist V 2.8 2.7 2.9

Pump speed r/min 375 375 375

Average injection quantity mm3/st. 19 17 21

Max. variation between cylinders % 0 -15 15

PS407980-224* V V1+0.05+ -0.01

PS407980-224* mm 8.4+-0.0 3

Remarks
Refer to items regarding the pre-stroke actuator

0000001201

Pre-stroke mm 8.5 8.47 8.53

Remarks
When the timing sleeve is pushed up

_02

Connector angle deg. 8.5 8 9

Remarks
When the eccentric pin is tightened

_03

Supply voltage V 24 23.5 24.5

Ambient temperature degC 23 18 28

Pre-stroke mm 6.1 6.05 6.15

Output voltage V 2.45 2.44 2.46

Adjustment *

_04

Supply voltage V 24 23.5 24.5

Ambient temperature degC 23 18 28

Pre-stroke mm 8.5 8.47 8.53

Output voltage V 1.2 1 1.4

Confirmation *

Remarks
Output voltage V1

_05

Supply voltage V 24 23.5 24.5

Ambient temperature degC 23 18 28

Pre-stroke mm 5.5

Output voltage V 3 2.98 3

Confirmation *

_06

Supply voltage V 24 23.5 24.5

Ambient temperature degC 23 18 28

Output voltage V 3.05 3.05

Confirmation of operating range *

Test data Ex:

Speed control lever angle

N:Pump normal S:Stop the pump. (1)Rack position = aa (2)Rack position bb
----------
aa=20mm bb=1mm
----------
a=35deg+-5deg b=37deg+-5deg

0000000901

(1)Pump vertical direction (2)Coupling's key groove position at No 1 cylinder's beginning of injection (3)At the No 1 cylinder's beginning of injection position, stamp an aligning mark on the damper to align with the pointer's groove. (4)Damper (5)Pointer (6)B.T.D.C.: aa (7)Pre-stroke: bb
----------
aa=6deg bb=8.5+-0.03mm
----------
a=44deg30min+-3deg b=(44deg)

0000001501

A:Sealing position B:Pre-stroke actuator 1. When installing the pre-stroke actuator on the pump, first tighten the installation bolts loosely, then move the actuator fully counterclockwise (viewed from the drive side). Temporary tightening torque: 1 - 1.5 N.m (0.1 - 0.15 kgf.m) 2. Move the actuator in the clockwise direction when viewed from the drive side, and adjust so that it becomes the adjustment point of the adjustment value. Then tighten it. Tightening torque: 7^9 N.m (0.7^0.9 kgf.m) 3. After prestroke actuator installation adjustment, simultaneously stamp both the actuator side and housing side.
----------

----------

0000001701

(Rs) rack sensor specifications (C/U) control unit part number (V) Rack sensor output voltage (R) Rack position (mm) 1. Confirming governor output characteristics (rack 19 mm, span 6 mm) (1)When the output voltages of the rack sensor are V1 and V2, check that the rack positions R1 and R2 in the table above are satisfied.
----------

----------

0000001901 RACK SENSOR

(VR) measurement voltage (I) Part number of the control unit (G) Apply red paint. (H): End surface of the pump 1. Rack sensor adjustment (154610-0620) (1)At governor side rack sensor output voltage V1, adjust the bobbin (A) so that the drive side rack sensor output voltage is VR+-0.01. (2)Apply G at two places. Connecting part between the joint (B) and the nut (F) Connecting part between the joint (B) and the end surface of the pump (H)
----------
V1=1.6V
----------