108622-1230 ZEXEL INJECTION-PUMP ASSEMBLY Calibration Data 1086221230 1156034090


108622-1230 INJECTION-PUMP ASSEMBLY
Rating:
52
Buy INJECTION-PUMP ASSEMBLY 108622-1230 zexel genuine, new aftermarket engine parts with delivery

Information injection-pump assembly

ZEXEL 108622-1230 1086221230
ISUZU 1156034090 1156034090

Cross reference number

ZEXEL 108622-1230 1086221230
ISUZU 1156034090 1156034090


Zexel num
Bosch num
Firm num
Name
108622-1230 
108622-1231 
 
1156034090  ISUZU
INJECTION-PUMP ASSEMBLY
6SD1-TCE * K

Calibration Data:

Adjustment conditions
Test oil
1404 Test oil
  ISO4113 or {SAEJ967d}
Test oil temperature degC   40 40 45
Nozzle and nozzle holder   105780-8250
Bosch type code   1 688 901 101
Nozzle   105780-0120
Bosch type code   1 688 901 990
Nozzle holder   105780-2190
Opening pressure MPa   20.7
Opening pressure kgf/cm2   211
Injection pipe
Outer diameter - inner diameter - length (mm)
mm   8-3-600
Overflow valve   131424-7120
Overflow valve opening pressure kPa   255 221 289
Overflow valve opening pressure kgf/cm2   2.6 2.25 2.95
Tester oil delivery pressure kPa   255 255 255
Tester oil delivery pressure kgf/cm2   2.6 2.6 2.6
PS/ACT control unit part no.   407980-2 24*
Digi switch no.   32
Direction of rotation (viewed from drive side)
Left
  L
Injection timing adjustment
Direction of rotation (viewed from drive side)
Left
  L
Injection order   1-5-3-6- 2-4
Pre-stroke mm   8.5 8.47 8.53
Beginning of injection position
Governor side
  NO.1
Difference between angles 1
Cal 1-5
deg.   60 59.75 60.25
Difference between angles 2
Cal 1-3
deg.   120 119.75 120.25
Difference between angles 3
Cal 1-6
deg.   180 179.75 180.25
Difference between angles 4
Cyl.1-2
deg.   240 239.75 240.25
Difference between angles 5
Cal 1-4
deg.   300 299.75 300.25
Injection quantity adjustment
Adjusting point   -
Rack position   12.9
Pump speed r/min   720 720 720
Average injection quantity mm3/st.   156.5 154.5 158.5
Max. variation between cylinders %   0 -3 3
Basic   *
Fixing the rack   *
PS407980-224* V   2.45+-0. 01
PS407980-224* mm   6.1+-0.0 5
Standard for adjustment of the maximum variation between cylinders   *
Injection quantity adjustment_02
Adjusting point   Z
Rack position   6.7+-0.5
Pump speed r/min   365 365 365
Average injection quantity mm3/st.   14.5 11.3 17.7
Max. variation between cylinders %   0 -13 13
Fixing the rack   *
PS407980-224* V   V1+0.05+ -0.01
PS407980-224* mm   8.4+-0.0 3
Standard for adjustment of the maximum variation between cylinders   *
Remarks
Refer to items regarding the pre-stroke actuator
 
Injection quantity adjustment_03
Adjusting point   A
Rack position   R1(12.9)
Pump speed r/min   720 720 720
Average injection quantity mm3/st.   156.5 154.5 158.5
Basic   *
Fixing the lever   *
Boost pressure kPa   53.3 53.3
Boost pressure mmHg   400 400
PS407980-224* V   2.45+-0. 01
PS407980-224* mm   6.1+-0.0 5
Injection quantity adjustment_04
Adjusting point   B
Rack position   R1+1.1
Pump speed r/min   1100 1100 1100
Average injection quantity mm3/st.   141.5 131.5 151.5
Fixing the lever   *
Boost pressure kPa   53.3 53.3
Boost pressure mmHg   400 400
PS407980-224* V   2.45+-0. 01
PS407980-224* mm   6.1+-0.0 5
Boost compensator adjustment
Pump speed r/min   500 500 500
Rack position   R2-1.7
Boost pressure kPa   8 6.7 9.3
Boost pressure mmHg   60 50 70
Boost compensator adjustment_02
Pump speed r/min   500 500 500
Rack position   R2[R1-1. 4]
Boost pressure kPa   40 40 40
Boost pressure mmHg   300 300 300
0000001601
Pre-stroke mm   8.5 8.47 8.53
Remarks
When the timing sleeve is pushed up
 
_02
Connector angle deg.   8.5 8 9
Remarks
When the eccentric pin is tightened
 
_03
Supply voltage V   24 23.5 24.5
Ambient temperature degC   23 18 28
Pre-stroke mm   6.1 6.05 6.15
Output voltage V   2.45 2.44 2.46
Adjustment   *
_04
Supply voltage V   24 23.5 24.5
Ambient temperature degC   23 18 28
Pre-stroke mm   8.5 8.47 8.53
Output voltage V   1.2 1 1.4
Confirmation   *
Remarks
Output voltage V1
 
_05
Supply voltage V   24 23.5 24.5
Ambient temperature degC   23 18 28
Pre-stroke mm   5.5
Output voltage V   3 2.98 3
Confirmation   *
_06
Supply voltage V   24 23.5 24.5
Ambient temperature degC   23 18 28
Output voltage V   3.05 3.05
Confirmation of operating range   *

Test data Ex:

Governor adjustment

Test data 108622-1230
N:Pump speed R:Rack position (mm) (1)Torque cam stamping: T1 (2)Tolerance for racks not indicated: +-0.05mm. (3)Boost compensator stroke: BCL
----------
T1=AF76 BCL=1.7+-0.1mm
----------

Speed control lever angle

Test data 108622-1230
F:Full speed I:Idle (1)Use the pin at R = aa (2)Stopper bolt setting
----------
aa=35mm
----------
a=22.5deg+-5deg b=30deg+-3deg

Stop lever angle

Test data 108622-1230
N:Pump normal S:Stop the pump. (1)Use the pin at R = aa (2)Set the stopper bolt so that speed = bb and rack position = cc. (Confirm non-injection.)
----------
aa=40mm bb=0r/min cc=1.5+-0.3mm
----------
a=14deg+-5deg b=41deg+-5deg

0000001301

Test data 108622-1230
(1)Pump vertical direction (2)Positions of coupling's threaded installation holes at No 1 cylinder's beginning of injection (3)At the No 1 cylinder's beginning of injection position, stamp an aligning mark on the damper to align with the pointer's groove. (4)Damper (5)Pointer (6)B.T.D.C.: aa (7)Pre-stroke: bb
----------
aa=5deg bb=8.5+-0.03mm
----------
a=(50deg) b=(44deg)

0000001901

Test data 108622-1230
A:Sealing position B:Pre-stroke actuator 1. When installing the pre-stroke actuator on the pump, first tighten the installation bolts loosely, then move the actuator fully counterclockwise (viewed from the drive side). Temporary tightening torque: 1 - 1.5 N.m (0.1 - 0.15 kgf.m) 2. Move the actuator in the clockwise direction when viewed from the drive side, and adjust so that it becomes the adjustment point of the adjustment value. Then tighten it. Tightening torque: 7^9 N.m (0.7^0.9 kgf.m) 3. After prestroke actuator installation adjustment, simultaneously stamp both the actuator side and housing side.
----------

----------

0000002201 RACK SENSOR

Test data 108622-1230
G:Red paint H:Pump end face P/N: part number of suitable shim (1)Threaded type rack block (2)Welded type rack block Rack sensor adjustment 1. Threaded type rack sensor (-5*20, P type, no TICS rack limit). (1)Screw in the bobbin (A) until it contacts the joint (B). (2)Fix the pump lever. (3)At speed N1 and rack position Ra, adjust the amount that the bobbin is screwed in so that the amp's output voltage is V1. (4)Fix using the nut (F). (5)Affix the caution plate to the upper part of the joint (B). (6)Apply (G) at two places. Connecting part between the joint (B) and the nut (F) Connecting part between the end surface of the pump (H) and the joint (B) 2. Range for screw-in adjustment between the bobbin (A) and the joint (B) is 9 threads. Screw in to the end from (the position where the bobbin (A) is rotated 9 turns). Speed N1, rack position Ra, output voltage V1, rack sensor supply voltage 5+-0.01 (V)
----------
Ra=R1(12.9)+1.1mm N1=1100r/min V1=3+-0.01V
----------




Have questions with 108622-1230?





Group cross 108622-1230 ZEXEL

Isuzu 

 
1156032960 
INJECTION-PUMP ASSEMBLY
6WG1-TC
 
1156032961 
INJECTION-PUMP ASSEMBLY
6WG1-TC
9 400 611 863 
1156032962 
INJECTION-PUMP ASSEMBLY
6WG1-TC
9 400 612 962 
1156032963 
INJECTION-PUMP ASSEMBLY
6WG1-TC
9 400 619 122 
1156032964 
INJECTION-PUMP ASSEMBLY
6WG1-TC
F 019 Z10 139 
1156032965 
INJECTION-PUMP ASSEMBLY
6WG1-TC
 
1156033660 
INJECTION-PUMP ASSEMBLY
6SD1-TC
F 019 Z10 783 
1156033661 
INJECTION-PUMP ASSEMBLY
6SD1-TC
 
1156033662 
INJECTION-PUMP ASSEMBLY
6SD1-TC
9 400 619 123 
1156033663 
INJECTION-PUMP ASSEMBLY
6SD1-TC
F 019 Z10 784 
1156033665 
INJECTION-PUMP ASSEMBLY
6SD1-TC
 
1156033600 
INJECTION-PUMP ASSEMBLY
6SD1-TCE
F 019 Z10 785 
1156033601 
INJECTION-PUMP ASSEMBLY
6SD1-TCE
9 400 613 488 
1156033602 
INJECTION-PUMP ASSEMBLY
6SD1-TCE
108622-1230  

108622-1231 
 
1156034090 
INJECTION-PUMP ASSEMBLY
6SD1-TCE
F 019 Z10 786 
1156034091 
INJECTION-PUMP ASSEMBLY
6SD1-TCE
9 400 619 124 
1156034092 
INJECTION-PUMP ASSEMBLY
6SD1-TCE
9 400 612 440 
1156034200 
INJECTION-PUMP ASSEMBLY
6WF1-TC
9 400 612 731 
1156034201 
INJECTION-PUMP ASSEMBLY
6WF1-TC
9 400 613 023 
1156034202 
INJECTION-PUMP ASSEMBLY
6WF1-TC
F 019 Z20 357 
1156034203 
INJECTION-PUMP ASSEMBLY
6WF1-TC
F 019 Z10 787 
1156032310 
INJECTION-PUMP ASSEMBLY
6TE1
 
1156032311 
INJECTION-PUMP ASSEMBLY
6TE1
9 400 619 125 
1156032312 
INJECTION-PUMP ASSEMBLY
6TE1
F 019 Z10 788 
1156034140 
INJECTION-PUMP ASSEMBLY
6WF1-TC
9 400 612 441 
1156034141 
INJECTION-PUMP ASSEMBLY
6WF1-TC
9 400 612 732 
1156034142 
INJECTION-PUMP ASSEMBLY
6WF1-TC
9 400 612 963 
1156034143 
INJECTION-PUMP ASSEMBLY
6WF1-TC
 
 
INJECTION-PUMP ASSEMBLY

Isuzu 

 
1156033770 
INJECTION-PUMP ASSEMBLY
6SD1-TC
9 400 619 126 
1156033771 
INJECTION-PUMP ASSEMBLY
6SD1-TC
F 019 Z10 304 
1156033772 
INJECTION-PUMP ASSEMBLY
6SD1-TC
F 019 Z10 910 
8976097260 
INJECTION-PUMP ASSEMBLY
6SD1-TC
F 01G 09U 1HZ 
8976109290 
INJECTION-PUMP ASSEMBLY
6SD1-TC
Back to top