106961-6170 ZEXEL INJECTION-PUMP ASSEMBLY Calibration Data 1069616170 1156027403


106961-6170 INJECTION-PUMP ASSEMBLY
Rating:
78
Buy INJECTION-PUMP ASSEMBLY 106961-6170 zexel genuine, new aftermarket engine parts with delivery

Information injection-pump assembly

ZEXEL 106961-6170 1069616170
ISUZU 1156027403 1156027403

Service parts 106961-6170 INJECTION-PUMP ASSEMBLY:

1. _
2. FUEL INJECTION PUMP 106096-9362
3. GOVERNOR 105488-0574
4. SUPPLY PUMP 105237-1940
5. AUTOM. ADVANCE MECHANIS 105693-0521
6. COUPLING PLATE
7. COUPLING PLATE
8. _
9. _
10. NOZZLE AND HOLDER ASSY 105100-7192
11. Nozzle and Holder
12. Open Pre:MPa(Kqf/cm2) 15.7(160)/22.1(225)
13. NOZZLE-HOLDER 105031-4831
14. NOZZLE 105015-6651
15. NOZZLE SET

Include in #1:

106961-6170 as INJECTION-PUMP ASSEMBLY

Cross reference number

ZEXEL 106961-6170 1069616170
ISUZU 1156027403 1156027403


Zexel num
Bosch num
Firm num
Name
106961-6170 
106961-6171 
 
1156027403  ISUZU
INJECTION-PUMP ASSEMBLY
12PC1 * K

Calibration Data:

Adjustment conditions
Test oil
1404 Test oil
  ISO4113 or {SAEJ967d}
Test oil temperature degC   40 40 45
Nozzle and nozzle holder   105780-8140
Bosch type code   EF8511/9A
Nozzle   105780-0000
Bosch type code   DN12SD12T
Nozzle holder   105780-2080
Bosch type code   EF8511/9
Opening pressure MPa   17.2
Opening pressure kgf/cm2   175
Injection pipe
Outer diameter - inner diameter - length (mm)
mm   8-3-600
Overflow valve (drive side)   134424-3520
Overflow valve opening pressure (drive side) kPa   255 221 289
Overflow valve opening pressure (drive side) kgf/cm2   2.6 2.25 2.95
Overflow valve (governor side)   134424-3520
Overflow valve opening pressure (governor side) kPa   255 221 289
Overflow valve opening pressure (governor side) kgf/cm2   2.6 2.25 2.95
Tester oil delivery pressure kPa   157 157 157
Tester oil delivery pressure kgf/cm2   1.6 1.6 1.6
Direction of rotation (viewed from drive side)
Right
  R
Injection timing adjustment
Direction of rotation (viewed from drive side)
Right
  R
Injection order   1-4-9-8- 5-2-11-1 0-3-6-7-
Pre-stroke mm   4 3.97 4.03
Beginning of injection position
Governor side
  NO.1
Difference between angles 1
Cal 1-4
deg.   15 14.75 15.25
Difference between angles 2
Cal 1-9
deg.   60 59.75 60.25
Difference between angles 3
Cal 1-8
deg.   75 74.75 75.25
Difference between angles 4
Cal 1-5
deg.   120 119.75 120.25
Difference between angles 5
Cyl.1-2
deg.   135 134.75 135.25
Difference between angles 6
Cal 1-11
deg.   180 179.75 180.25
Difference between angles 7
Cal 1-10
deg.   195 194.75 195.25
Difference between angles 8
Cal 1-3
deg.   240 239.75 240.25
Difference between angles 9
Cal 1-6
deg.   255 254.75 255.25
Difference between angles 10
Cal 1-7
deg.   300 299.75 300.25
Difference between angles 11
Cal 1-12
deg.   315 314.75 315.25
Injection quantity adjustment
Adjusting point   B
Rack position   8.1
Pump speed r/min   700 700 700
Average injection quantity mm3/st.   85.6 84.1 87.1
Max. variation between cylinders %   0 -2 2
Basic   *
Fixing the lever   *
Injection quantity adjustment_02
Adjusting point   C
Rack position   7.9+-0.5
Pump speed r/min   1250 1250 1250
Average injection quantity mm3/st.   95.9 91.9 99.9
Max. variation between cylinders %   0 -3 3
Fixing the lever   *
Injection quantity adjustment_03
Adjusting point   D
Rack position   5.4+-0.5
Pump speed r/min   225 225 225
Average injection quantity mm3/st.   8 6.6 9.4
Max. variation between cylinders %   0 -13 13
Fixing the rack   *
Injection quantity adjustment_04
Adjusting point   F
Rack position   -
Pump speed r/min   150 150 150
Average injection quantity mm3/st.   137 137
Fixing the lever   *
Remarks
When manual lever is on the boost side
 

Test data Ex:

Governor adjustment

Test data 106961-6170
N:Pump speed R:Rack position (mm) (1)Lever ratio: RT (2)Target shim dimension: TH (3)Tolerance for racks not indicated: +-0.05mm. (4)Supplied with torque spring not set. (5)Supply solenoid operating voltage DC24V and move the solenoid body so that the excess lever reaches the excess position at the solenoid's maximum stroke. (6)At excess fuel lever operation: not exceeding EXL (7)Excess fuel setting for starting: SXL (N = N1)
----------
RT=0.8 TH=2.4mm EXL=2mm SXL=9.2+-0.1mm N1=320r/min
----------

Timer adjustment

Test data 106961-6170
(1)Adjusting range (2)Step response time (N): Speed of the pump (L): Load (theta) Advance angle (Srd1) Step response time 1 (Srd2) Step response time 2 1. Adjusting conditions for the variable timer (1)Adjust the clearance between the pickup and the protrusion to L.
----------
L=1-0.2mm N2=800r/min C2=(7)deg t1=1.5--sec. t2=1.5--sec.
----------
N1=1100++r/min P1=0kPa(0kgf/cm2) P2=392kPa(4kgf/cm2) C1=7+-0.3deg R01=0/4load R02=4/4load

Speed control lever angle

Test data 106961-6170
F:Full speed
----------

----------
a=9deg+-5deg

0000000901

Test data 106961-6170
F:Full load I:Idle (1)Stopper bolt setting (2)Use the hole at R = aa
----------
aa=35mm
----------
a=10deg+-5deg b=33deg+-3deg

Stop lever angle

Test data 106961-6170
N:Pump normal S:Stop the pump.
----------

----------
a=60deg+-5deg b=73deg+-5deg

0000001101

Test data 106961-6170
N:Normal B:When boosted
----------

----------
a=(5deg) b=(24deg)

0000001501 RACK SENSOR

Test data 106961-6170
V1:Supply voltage V2f:Full side output voltage V2i:Idle side output voltage (A) Black (B) Yellow (C) Red (D) Trimmer (E): Shaft (F) Nut (G) Load lever 1. Load sensor adjustment (1)Connect as shown in the above diagram and apply supply voltage V1. (2)Hold the load lever (G) against the full side. (3)Turn the shaft so that the voltage between (A) and (B) is V2. (4)Hold the load lever (G) against the idle side. (5)Adjust (D) so that the voltage between (A) and (B) is V2i. (6)Repeat the above adjustments. (7)Tighten the nut (F) at the point satisfying the standards. (8)Hold the load lever against the full side stopper and the idle side stopper. (9)At this time, confirm that the full side output voltage is V2f and the idle side output voltage is V2i.
----------
V1=5+-0.02V V2f=0.15+0.03V V2i=2.35-0.03V
----------

0000001601 SPEED SENSOR

Test data 106961-6170
(A) Flyweight projection (B) Pickup sensor (c) Lock nut Speed sensor installation (1)Install the speed sensor so that the clearance between the sensor and the flyweight projection is L. (This gap is the gap when the pickup sensor is returned 1 turn from where it contacts the flyweight tooth.)
----------
L=0.8~1mm
----------

Timing setting

Test data 106961-6170
(1)Pump vertical direction (2)Position of "Z" mark at the No 1 cylinder's beginning of injection (governor side) (3)B.T.D.C.: aa (4)-
----------
aa=12deg
----------
a=(170deg)




Have questions with 106961-6170?





Group cross 106961-6170 ZEXEL

Isuzu 

 
1156028390 
INJECTION-PUMP ASSEMBLY
12PD1-N
 
1156028391 
INJECTION-PUMP ASSEMBLY
12PD1-N
 
1156028392 
INJECTION-PUMP ASSEMBLY
12PD1-N
 
1156028393 
INJECTION-PUMP ASSEMBLY
12PD1-N
 
1156030160 
INJECTION-PUMP ASSEMBLY
12PD1-N
9 400 618 606 
1156030161 
INJECTION-PUMP ASSEMBLY
12PD1-N
 
1156029120 
INJECTION-PUMP ASSEMBLY
10PD1
9 400 618 607 
1156029121 
INJECTION-PUMP ASSEMBLY
10PD1
 
1156029130 
INJECTION-PUMP ASSEMBLY
10PD1
9 400 618 608 
1156029131 
INJECTION-PUMP ASSEMBLY
10PD1
 
1156029140 
INJECTION-PUMP ASSEMBLY
12PD1
9 400 618 609 
1156029141 
INJECTION-PUMP ASSEMBLY
12PD1
 
1156030210 
INJECTION-PUMP ASSEMBLY
10PD1
 
1156030211 
INJECTION-PUMP ASSEMBLY
10PD1
 
1156030212 
INJECTION-PUMP ASSEMBLY
10PD1
9 400 618 610 
1156030213 
INJECTION-PUMP ASSEMBLY
10PD1
9 400 613 337 
1156013948 
INJECTION-PUMP ASSEMBLY
12PC1
9 400 618 611 
1156013949 
INJECTION-PUMP ASSEMBLY
12PC1
 
1156027383 
INJECTION-PUMP ASSEMBLY
10PC1
 
1156027384 
INJECTION-PUMP ASSEMBLY
10PC1
106961-6170  

106961-6171 
 
1156027403 
INJECTION-PUMP ASSEMBLY
12PC1
 
1156027404 
INJECTION-PUMP ASSEMBLY
12PC1
 
1156028152 
INJECTION-PUMP ASSEMBLY
12PC1
 
1156028153 
INJECTION-PUMP ASSEMBLY
12PC1
 
1156026333 
INJECTION-PUMP ASSEMBLY
10PC1
Back to top