106873-3730 ZEXEL INJECTION-PUMP ASSEMBLY Calibration Data 1068733730 222400377a


106873-3730 INJECTION-PUMP ASSEMBLY
Rating:
53
Buy INJECTION-PUMP ASSEMBLY 106873-3730 zexel genuine, new aftermarket engine parts with delivery

Information injection-pump assembly

ZEXEL 106873-3730 1068733730
HINO 222400377A 222400377a

Cross reference number

ZEXEL 106873-3730 1068733730
HINO 222400377A 222400377a


Zexel num
Bosch num
Firm num
Name
106873-3730 
 
222400377A  HINO
INJECTION-PUMP ASSEMBLY
F17D-C * K 14CD PE8P PE

Calibration Data:

Adjustment conditions
Test oil
1404 Test oil
  ISO4113 or {SAEJ967d}
Test oil temperature degC   40 40 45
Nozzle and nozzle holder   105780-8250
Bosch type code   1 688 901 101
Nozzle   105780-0120
Bosch type code   1 688 901 990
Nozzle holder   105780-2190
Opening pressure MPa   20.7
Opening pressure kgf/cm2   211
Injection pipe
Outer diameter - inner diameter - length (mm)
mm   8-3-600
Overflow valve   134424-4120
Overflow valve opening pressure kPa   255 221 289
Overflow valve opening pressure kgf/cm2   2.6 2.25 2.95
Tester oil delivery pressure kPa   255 255 255
Tester oil delivery pressure kgf/cm2   2.6 2.6 2.6
Direction of rotation (viewed from drive side)
Right
  R
Injection timing adjustment
Direction of rotation (viewed from drive side)
Right
  R
Injection order   1-8-6-2- 7-5-4-3
Pre-stroke mm   4.2 4.14 4.2
Beginning of injection position
Drive side
  NO.1
Difference between angles 1
Cal 1-8
deg.   45 44.75 45.25
Difference between angles 2
Cal 1-6
deg.   90 89.75 90.25
Difference between angles 3
Cyl.1-2
deg.   135 134.75 135.25
Difference between angles 4
Cal 1-7
deg.   180 179.75 180.25
Difference between angles 5
Cal 1-5
deg.   225 224.75 225.25
Difference between angles 6
Cal 1-4
deg.   270 269.75 270.25
Difference between angles 7
Cal 1-3
deg.   315 314.75 315.25
Injection quantity adjustment
Adjusting point   -
Rack position   12.3
Pump speed r/min   700 700 700
Average injection quantity mm3/st.   131 128 134
Max. variation between cylinders %   0 -3 3
Basic   *
Fixing the rack   *
Standard for adjustment of the maximum variation between cylinders   *
Injection quantity adjustment_02
Adjusting point   Z
Rack position   8+-0.5
Pump speed r/min   460 460 460
Average injection quantity mm3/st.   13.3 12.3 14.3
Max. variation between cylinders %   0 -10 10
Fixing the rack   *
Standard for adjustment of the maximum variation between cylinders   *
Injection quantity adjustment_03
Adjusting point   A
Rack position   R1(12.3)
Pump speed r/min   700 700 700
Average injection quantity mm3/st.   131 129 133
Basic   *
Fixing the lever   *
Injection quantity adjustment_04
Adjusting point   B
Rack position   R1+0.5
Pump speed r/min   1100 1100 1100
Average injection quantity mm3/st.   121.5 115.5 127.5
Fixing the lever   *
Timer adjustment
Pump speed r/min   760--
Advance angle deg.   0 0 0
Remarks
Start
 
Timer adjustment_02
Pump speed r/min   710
Advance angle deg.   0.3
Timer adjustment_03
Pump speed r/min   (770)
Advance angle deg.   2.25 1.95 2.55
Remarks
Measure the actual speed.
 
Timer adjustment_04
Pump speed r/min   (900)
Advance angle deg.   2.25 1.95 2.55
Remarks
Measure the actual speed.
 
Timer adjustment_05
Pump speed r/min   1050+50
Advance angle deg.   6.75 6.45 7.05
Remarks
Finish
 

Test data Ex:

Governor adjustment

Test data 106873-3730
N:Pump speed R:Rack position (mm) (1)Torque cam stamping: T1 (2)Set stop lever before governor adjustment. [When setting stop lever after governor adjustment, confirm that point I (Ra) can be obtained at full setting.] (3)Stop lever's normal position setting: equivalent to RA (4)Damper spring setting
----------
T1=AG39 Ra=R1+1mm RA=17.5mm
----------

Speed control lever angle

Test data 106873-3730
F:Full speed I:Idle (1)Use the hole at R = aa (2)Stopper bolt set position 'H'
----------
aa=94mm
----------
a=17deg+-5deg b=40.5deg+-3deg

Stop lever angle

Test data 106873-3730
N:Pump normal S:Stop the pump. (1)Rack position = aa (2)Set the stopper screw. (After setting, apply red paint.) (3)Rack position = bb (speed = cc) (4)Set the stopper screw. (After setting, apply red paint.) (5)Use the hole above R = dd
----------
aa=(17.5)mm bb=1+-0.3mm cc=0r/min dd=35mm
----------
a=35deg+-5deg b=29.5deg+-5deg

Timing setting

Test data 106873-3730
(1)Pump vertical direction (2)Coupling's key groove position at No 1 cylinder's beginning of injection (3)- (4)-
----------

----------
a=(80deg)




Have questions with 106873-3730?





Group cross 106873-3730 ZEXEL

Hino 

9 400 618 454 
220801810A 
INJECTION-PUMP ASSEMBLY
F17D-TI
 
220009900A 
INJECTION-PUMP ASSEMBLY
YJ41
9 400 618 455 
220009901A 
INJECTION-PUMP ASSEMBLY
YJ41
 
220401440A 
INJECTION-PUMP ASSEMBLY
YJ42
 
220401441A 
INJECTION-PUMP ASSEMBLY
YJ42
9 400 618 456 
220401443A 
INJECTION-PUMP ASSEMBLY
YJ42
106873-3730  
 
222400377A 
INJECTION-PUMP ASSEMBLY
F17D-C
9 400 618 457 
220402140A 
INJECTION-PUMP ASSEMBLY
F21C
9 400 618 458 
220402150A 
INJECTION-PUMP ASSEMBLY
F17D-C
Back to top