106873-3470 ZEXEL INJECTION-PUMP ASSEMBLY Calibration Data 1068733470 220801740a


106873-3470 INJECTION-PUMP ASSEMBLY
Rating:
9
Buy INJECTION-PUMP ASSEMBLY 106873-3470 zexel genuine, new aftermarket engine parts with delivery

Information injection-pump assembly

ZEXEL 106873-3470 1068733470
HINO 220801740A 220801740a

Cross reference number

ZEXEL 106873-3470 1068733470
HINO 220801740A 220801740a


Zexel num
Bosch num
Firm num
Name
106873-3470 
106873-3471 
 
220801740A  HINO
INJECTION-PUMP ASSEMBLY
F17E * K

Calibration Data:

Adjustment conditions
Test oil
1404 Test oil
  ISO4113 or {SAEJ967d}
Test oil temperature degC   40 40 45
Nozzle and nozzle holder   105780-8140
Bosch type code   EF8511/9A
Nozzle   105780-0000
Bosch type code   DN12SD12T
Nozzle holder   105780-2080
Bosch type code   EF8511/9
Opening pressure MPa   17.2
Opening pressure kgf/cm2   175
Injection pipe
Outer diameter - inner diameter - length (mm)
mm   8-3-600
Overflow valve   134424-0820
Overflow valve opening pressure kPa   127 107 147
Overflow valve opening pressure kgf/cm2   1.3 1.1 1.5
Tester oil delivery pressure kPa   157 157 157
Tester oil delivery pressure kgf/cm2   1.6 1.6 1.6
Direction of rotation (viewed from drive side)
Right
  R
Injection timing adjustment
Direction of rotation (viewed from drive side)
Right
  R
Injection order   1-8-6-2- 7-5-4-3
Pre-stroke mm   4.8 4.74 4.8
Beginning of injection position
Drive side
  NO.1
Difference between angles 1
Cal 1-8
deg.   45 44.75 45.25
Difference between angles 2
Cal 1-6
deg.   90 89.75 90.25
Difference between angles 3
Cyl.1-2
deg.   135 134.75 135.25
Difference between angles 4
Cal 1-7
deg.   180 179.75 180.25
Difference between angles 5
Cal 1-5
deg.   225 224.75 225.25
Difference between angles 6
Cal 1-4
deg.   270 269.75 270.25
Difference between angles 7
Cal 1-3
deg.   315 314.75 315.25
Injection quantity adjustment
Adjusting point   A
Rack position   8.9
Pump speed r/min   700 700 700
Average injection quantity mm3/st.   139.3 137.3 141.3
Max. variation between cylinders %   0 -2 2
Basic   *
Fixing the lever   *
Injection quantity adjustment_02
Adjusting point   B
Rack position   8.95+-0. 5
Pump speed r/min   1100 1100 1100
Average injection quantity mm3/st.   133.1 129.1 137.1
Fixing the lever   *
Injection quantity adjustment_03
Adjusting point   F
Rack position   3.8+-0.5
Pump speed r/min   225 225 225
Average injection quantity mm3/st.   10.4 7.4 13.4
Max. variation between cylinders %   0 -15 15
Fixing the rack   *
Injection quantity adjustment_04
Adjusting point   G
Rack position   -
Pump speed r/min   100 100 100
Average injection quantity mm3/st.   139 139
Fixing the lever   *
Remarks
After startup boost setting
 
Timer adjustment
Pump speed r/min   -
Advance angle deg.   0 0 0
Remarks
Measure speed (beginning of operation).
 
Timer adjustment_02
Pump speed r/min   1060
Advance angle deg.   4.75 4.45 5.05
Remarks
Finish
 

Test data Ex:

Governor adjustment

Test data 106873-3470
N:Pump speed R:Rack position (mm) (1)Tolerance for racks not indicated: +-0.05mm. (2)Set idle at point K (N = N1, R = R1) and confirm that the injection quantity does not exceed Q1 at point J (N = N2). (3)Excess fuel setting for starting: SXL (4)Damper spring setting (5)Variable speed specification: idling adjustment (6)Main spring setting
----------
N1=325r/min R1=3.8mm N2=1100r/min Q1=3mm3/st SXL=9.45+-0.1mm
----------

Speed control lever angle

Test data 106873-3470
F:Full speed I:Idle (1)Set the pump speed at aa (2)Set the pump speed at bb. (3)Stopper bolt setting (4)Stopper bolt setting (5)Use the hole above R = cc
----------
aa=1295r/min bb=350r/min cc=95mm
----------
a=(19.5deg)+-5deg b=(18deg)+-5deg

0000000901

Test data 106873-3470
F:Full load I:Idle (1)Use the hole at R = aa (2)Stopper bolt setting
----------
aa=42mm
----------
a=39deg+-5deg b=43.5deg+-3deg

Stop lever angle

Test data 106873-3470
N:Pump normal S:Stop the pump. (1)Rack position = aa (at delivery), set before governor adjustment (2)Use the pin at R = bb (3)Set the stopper bolt (apply red paint).
----------
aa=12+-0.1mm bb=37mm
----------
a=0deg+-5deg b=35deg+-5deg

0000001201

Test data 106873-3470
(1)Minimum - maximum speed specification (2)Variable speed specification (3)(Actual measurement) (4)(Actual measurement) (5)Use the hole at R = aa
----------
aa=75mm
----------

0000001501 LEVER

Test data 106873-3470
2-stage changeover lever adjustment (A) Speed lever (B) Load lever (C) 2-stage changeover lever (D) Link (E) Bolt (G) Variable speed specifications (H) Minimum maximum speed specifications F:Full speed I:Idle 1. Minimum-maximum speed specification adjustment (when running) (1)After completing governor adjustment, hold the 2-stage changeover lever (C) so that the speed lever (A) contacts the full speed stopper. (2)In this condition, the load lever is held in the idle position. (3)Adjust bolt (E) so that the clearance between the pin underneath lever (C) and the end of the long groove in link (D) is L. (4)Lock using the nut. 2. Variable speed specification adjustment (at operation) (1)Hold the 2-stage changeover lever (C) so that the load lever (B) contacts the full load stopper. (When the load lever is equipped with a cancel mechanism, move it so that it contacts the stopper without canceling.) (2)In this condition, confirm that the speed lever (A) moves from idle to full speed.
----------
L=1~2mm
----------

Timing setting

Test data 106873-3470
(1)Pump vertical direction (2)Coupling's key groove position at No 1 cylinder's beginning of injection (3)- (4)-
----------

----------
a=(80deg)




Have questions with 106873-3470?





Group cross 106873-3470 ZEXEL

Hino 

 
220008970A 
INJECTION-PUMP ASSEMBLY
F-2
 
220008971A 
INJECTION-PUMP ASSEMBLY
F-2
9 400 611 025 
220008972A 
INJECTION-PUMP ASSEMBLY
F-2
 
220801670A 
INJECTION-PUMP ASSEMBLY
F-2
 
220801671A 
INJECTION-PUMP ASSEMBLY
F-2
9 400 611 026 
220801672A 
INJECTION-PUMP ASSEMBLY
F-2
 
 
INJECTION-PUMP ASSEMBLY

Hino 

 
220009030A 
INJECTION-PUMP ASSEMBLY
F-3
9 400 618 435 
220009150A 
INJECTION-PUMP ASSEMBLY
F20C
 
 
INJECTION-PUMP ASSEMBLY

Hino 

 
S220801660A 
INJECTION-PUMP ASSEMBLY
9 400 618 436 
220801660A 
INJECTION-PUMP ASSEMBLY
EF750T
9 400 618 437 
220009160A 
INJECTION-PUMP ASSEMBLY
F20C
9 400 611 027 
220009220A 
INJECTION-PUMP ASSEMBLY
F17E
106873-3470  

106873-3471 
 
220801740A 
INJECTION-PUMP ASSEMBLY
F17E
9 400 618 438 
220801741A 
INJECTION-PUMP ASSEMBLY
F17E
9 400 618 438 
S220801741 
INJECTION-PUMP ASSEMBLY
F17E
 
220009251A 
INJECTION-PUMP ASSEMBLY
F17D-C
F 01G 09U 0B6 
 
INJECTION-PUMP ASSEMBLY

Hino 

F 01G 09U 0B7 
220009252A 
INJECTION-PUMP ASSEMBLY
F17D-C
 
220009261A 
INJECTION-PUMP ASSEMBLY
F-3
 
220009261B 
INJECTION-PUMP ASSEMBLY
F-3
F 01G 09U 0B8 
 
INJECTION-PUMP ASSEMBLY

Hino 

9 400 611 631 
220009262A 
INJECTION-PUMP ASSEMBLY
F-3
Back to top