106871-5510 ZEXEL 9 400 611 020 BOSCH INJECTION-PUMP ASSEMBLY 9400611020 1068715510 1680197564


106871-5510 INJECTION-PUMP ASSEMBLY
Rating:
26
Buy INJECTION-PUMP ASSEMBLY 106871-5510 zexel genuine, new aftermarket engine parts with delivery

Information injection-pump assembly

BOSCH 9 400 611 020 9400611020
ZEXEL 106871-5510 1068715510
NISSAN-DIESEL 1680197564 1680197564

Service parts 106871-5510 INJECTION-PUMP ASSEMBLY:

1. _
2. FUEL INJECTION PUMP 106080-5730
3. GOVERNOR 105952-2020
4. SUPPLY PUMP 105237-4710
5. AUTOM. ADVANCE MECHANIS 105683-0710
6. COUPLING PLATE 105663-0570
7. COUPLING PLATE
8. _
9. _
10. NOZZLE AND HOLDER ASSY 105110-7651
11. Nozzle and Holder 16600-97160
12. Open Pre:MPa(Kqf/cm2) 15.7{160}/22.6{230}
13. NOZZLE-HOLDER 105041-3150
14. NOZZLE
15. NOZZLE SET 105019-0591

Include in #1:

106871-5510 as INJECTION-PUMP ASSEMBLY

Cross reference number

BOSCH 9 400 611 020 9400611020
ZEXEL 106871-5510 1068715510
NISSAN-DIESEL 1680197564 1680197564


Zexel num
Bosch num
Firm num
Name
106871-5510 
106871-5573 
9 400 611 020 
1680197564  NISSAN-DIESEL
INJECTION-PUMP ASSEMBLY
RH8 * K 14CD INJECTION PUMP ASSY PE8P PE

Calibration Data:

Adjustment conditions
Test oil
1404 Test oil
  ISO4113 or {SAEJ967d}
Test oil temperature degC   40 40 45
Nozzle and nozzle holder   105780-8250
Bosch type code   1 688 901 101
Nozzle   105780-0120
Bosch type code   1 688 901 990
Nozzle holder   105780-2190
Opening pressure MPa   20.7
Opening pressure kgf/cm2   211
Injection pipe
Outer diameter - inner diameter - length (mm)
mm   8-3-600
Overflow valve   131425-0120
Overflow valve opening pressure kPa   157 123 191
Overflow valve opening pressure kgf/cm2   1.6 1.25 1.95
Tester oil delivery pressure kPa   255 255 255
Tester oil delivery pressure kgf/cm2   2.6 2.6 2.6
RED3 control unit part number   407910-3 960
RED3 rack sensor specifications mm   19
Direction of rotation (viewed from drive side)
Right
  R
Injection timing adjustment
Direction of rotation (viewed from drive side)
Right
  R
Injection order   1-8-7-5- 4-3-6-2
Pre-stroke mm   4.4 4.37 4.43
Beginning of injection position
Governor side
  NO.1
Difference between angles 1
Cal 1-8
deg.   45 44.75 45.25
Difference between angles 2
Cal 1-7
deg.   90 89.75 90.25
Difference between angles 3
Cal 1-5
deg.   135 134.75 135.25
Difference between angles 4
Cal 1-4
deg.   180 179.75 180.25
Difference between angles 5
Cal 1-3
deg.   225 224.75 225.25
Difference between angles 6
Cal 1-6
deg.   270 269.75 270.25
Difference between angles 7
Cyl.1-2
deg.   315 314.75 315.25
Injection quantity adjustment
Rack position   (13.2)
Vist V   1.87 1.87 1.87
Pump speed r/min   700 700 700
Average injection quantity mm3/st.   128 126 130
Max. variation between cylinders %   0 -4 4
Basic   *
Injection quantity adjustment_02
Rack position   (8.6)
Vist V   2.6 2.5 2.7
Pump speed r/min   390 390 390
Average injection quantity mm3/st.   16 14 18
Max. variation between cylinders %   0 -10 10
Governor adjustment
Pump speed r/min   750--
Advance angle deg.   0 0 0
Remarks
At Q=169+-2 (mm3/st) / N=700 (r/min), start of advance
 
Governor adjustment_02
Pump speed r/min   700
Advance angle deg.   0.3
Remarks
Q=169+-2 (mm3/st) / N=700 (r/min)
 
Governor adjustment_03
Pump speed r/min   (750)
Advance angle deg.   2 1.7 2.3
Remarks
Q=169+-2 (mm3/st) / N=700 (r/min)
 
Governor adjustment_04
Pump speed r/min   850
Advance angle deg.   2 1.7 2.3
Remarks
Q=97+-2 (mm3/st) / N=850 (r/min)
 
Governor adjustment_05
Pump speed r/min   1100
Advance angle deg.   7 6.7 7.3
Remarks
Q=162+-2 (mm3/st) / N=1100 (r/min), end of advance
 

Test data Ex:

Speed control lever angle

Test data 106871-5510
N:Pump normal S:Stop the pump. (1)Rack position = aa (2)Rack position bb
----------
aa=20mm bb=1mm
----------
a=27deg+-5deg b=37deg+-5deg

0000000901

Test data 106871-5510
(1)Pump vertical direction (2)Position of the coupling's key groove at the beginning of injection of the No. 8 cylinder. (3)- (4)-
----------

----------
a=(90deg)

Stop lever angle

Test data 106871-5510
(Rs) rack sensor specifications (C/U) control unit part number (V) Rack sensor output voltage (R) Rack position (mm) 1. Confirming governor output characteristics (rack 19 mm, span 6 mm) (1)When the output voltages of the rack sensor are V1 and V2, check that the rack positions R1 and R2 in the table above are satisfied.
----------

----------




Have questions with 106871-5510?





Group cross 106871-5510 ZEXEL

Nissan-Diesel 

9 400 611 019 
1680197563 
INJECTION-PUMP ASSEMBLY
RG8
106871-5510  

106871-5573 
9 400 611 020 
1680197564 
INJECTION-PUMP ASSEMBLY
RH8
9 400 618 170 
1680197566 
INJECTION-PUMP ASSEMBLY
RG8
F 01G 09U 09Z 
 
INJECTION-PUMP ASSEMBLY
F 01G 09U 0A0 
 
INJECTION-PUMP ASSEMBLY
F 01G 09U 0A1 
 
INJECTION-PUMP ASSEMBLY
RF8

Nissan-Diesel 

9 400 618 171 
1680197568 
INJECTION-PUMP ASSEMBLY
RF8
 
1680197573 
INJECTION-PUMP ASSEMBLY
RF8TA
 
 
INJECTION-PUMP ASSEMBLY
 
 
INJECTION-PUMP ASSEMBLY

Nissan-Diesel 

9 400 618 172 
1680197579 
INJECTION-PUMP ASSEMBLY
RF8TA
F 01G 09U 0A2 
 
INJECTION-PUMP ASSEMBLY
F 01G 09U 0A3 
 
INJECTION-PUMP ASSEMBLY
F 01G 09U 0A4 
 
INJECTION-PUMP ASSEMBLY
RG8

Nissan-Diesel 

9 400 618 173 
1680197569 
INJECTION-PUMP ASSEMBLY
RG8
 
1680197570 
INJECTION-PUMP ASSEMBLY
RG8
F 01G 09U 0A5 
 
INJECTION-PUMP ASSEMBLY
F 01G 09U 0A6 
 
INJECTION-PUMP ASSEMBLY

Nissan-Diesel 

9 400 618 174 
1680197578 
INJECTION-PUMP ASSEMBLY
RG8
F 01G 09U 0A7 
 
INJECTION-PUMP ASSEMBLY
F 01G 09U 0A8 
 
INJECTION-PUMP ASSEMBLY
F 01G 09U 0A9 
 
INJECTION-PUMP ASSEMBLY
RH8

Nissan-Diesel 

9 400 618 175 
1680197571 
INJECTION-PUMP ASSEMBLY
RH8
 
 
INJECTION-PUMP ASSEMBLY
 
 
INJECTION-PUMP ASSEMBLY
9 400 619 880 
 
INJECTION-PUMP ASSEMBLY
RF8

Nissan-Diesel 

9 400 618 176 
1680197574 
INJECTION-PUMP ASSEMBLY
RF8
 
 
INJECTION-PUMP ASSEMBLY
 
 
INJECTION-PUMP ASSEMBLY
F 01G 09U 0AA 
 
INJECTION-PUMP ASSEMBLY
RG8

Nissan-Diesel 

9 400 618 177 
1680197575 
INJECTION-PUMP ASSEMBLY
RG8
Back to top