106682-4644 ZEXEL 9 400 611 841 BOSCH INJECTION-PUMP ASSEMBLY 9400611841 1066824644 35a6530330

Information Cross number Calibration Data Calibration Data Ex

Price: query
Buy now
Add to cart Go to cart

Rating:

Buy INJECTION-PUMP ASSEMBLY 106682-4644 zexel genuine, new aftermarket engine parts with delivery

Information injection-pump assembly

BOSCH 9 400 611 841 9400611841

ZEXEL 106682-4644 1066824644

MITSUBISHI-HEAV 35A6530330 35a6530330

Service parts 106682-4644 INJECTION-PUMP ASSEMBLY:

1. _

2. FUEL INJECTION PUMP 106068-2981

3. GOVERNOR 105447-5840

4. SUPPLY PUMP 105237-1690

5. AUTOM. ADVANCE MECHANIS

6. COUPLING PLATE 105664-0670

7. COUPLING PLATE 156638-2420

8. _

9. _

10. NOZZLE AND HOLDER ASSY 105101-6220

11. Nozzle and Holder 35A61-00010

12. Open Pre:MPa(Kqf/cm2) 21.6{220}

13. NOZZLE-HOLDER 105030-4320

14. NOZZLE 105015-8520

15. NOZZLE SET

Include in #1:

106682-4644 as INJECTION-PUMP ASSEMBLY

Cross reference number

BOSCH 9 400 611 841 9400611841

ZEXEL 106682-4644 1066824644

MITSUBISHI-HEAV 35A6530330 35a6530330

Zexel num

Bosch num

Firm num

Name

106682-4644
106682-4645

9 400 611 841

35A6530330 MITSUBISHI-HEAV

INJECTION-PUMP ASSEMBLY
S6A3 * K

Calibration Data:

Adjustment conditions

Test oil
1404 Test oil ISO4113 or {SAEJ967d}

Test oil temperature degC 40 40 45

Nozzle and nozzle holder 105780-8130

Bosch type code EFEP215A

Nozzle 105780-0050

Bosch type code DN6TD119NP1T

Nozzle holder 105780-2090

Bosch type code EFEP215

Opening pressure MPa 17.2

Opening pressure kgf/cm2 175

Injection pipe
Outer diameter - inner diameter - length (mm) mm 8-4-1000

Overflow valve 131424-3420

Overflow valve opening pressure kPa 255 221 289

Overflow valve opening pressure kgf/cm2 2.6 2.25 2.95

Tester oil delivery pressure kPa 157 157 157

Tester oil delivery pressure kgf/cm2 1.6 1.6 1.6

Direction of rotation (viewed from drive side)
Left L

Injection timing adjustment

Direction of rotation (viewed from drive side)
Left L

Injection order 1-5-3-6- 2-4

Pre-stroke mm 2.8 2.75 2.85

Rack position
Point A R=A

Beginning of injection position
Governor side NO.1

Difference between angles 1
Cal 1-5 deg. 60 59.5 60.5

Difference between angles 2
Cal 1-3 deg. 120 119.5 120.5

Difference between angles 3
Cal 1-6 deg. 180 179.5 180.5

Difference between angles 4
Cyl.1-2 deg. 240 239.5 240.5

Difference between angles 5
Cal 1-4 deg. 300 299.5 300.5

Injection quantity adjustment

Adjusting point A

Rack position 15.3

Pump speed r/min 900 900 900

Average injection quantity mm3/st. 553 544 562

Max. variation between cylinders % 0 -3 3

Basic *

Fixing the lever *

Injection quantity adjustment_02

Adjusting point B

Rack position 6.6+-0.5

Pump speed r/min 250 250 250

Average injection quantity mm3/st. 25 22 28

Max. variation between cylinders % 0 -10 10

Fixing the rack *

Test data Ex:

Governor adjustment

N:Pump speed R:Rack position (mm) (1)Minimum - maximum speed specification (2)Adjust at speed lever's full position. (3)Target notch: K (4)Tolerance for racks not indicated: +-0.05mm. (5)Idle sub spring setting: L1.
----------
K=12 L1=6.8-0.5mm
----------

Speed control lever angle

F:Full speed S:Stop (1)At the center of the lever key groove
----------

----------
a=17.5deg+-5deg b=33deg+-3deg

0000000901

F:Full load I:Idle S:Stop (1)Stop side boss position (2)Use the screw at R = aa
----------
aa=60mm
----------
a=19deg+-5deg b=30deg+-5deg c=29deg+-5deg