106675-4660 ZEXEL INJECTION-PUMP ASSEMBLY Calibration Data 1066754660

Information Cross number Calibration Data Calibration Data Ex

Price: query
Buy now
Add to cart Go to cart

Rating:

Buy INJECTION-PUMP ASSEMBLY 106675-4660 zexel genuine, new aftermarket engine parts with delivery

Information injection-pump assembly

ZEXEL 106675-4660 1066754660

Service parts 106675-4660 INJECTION-PUMP ASSEMBLY:

1. _

2. FUEL INJECTION PUMP 106067-6090

3. GOVERNOR 105407-7560

4. SUPPLY PUMP 105237-5470

5. AUTOM. ADVANCE MECHANIS

6. COUPLING PLATE 105663-0470

7. COUPLING PLATE

8. _

9. _

10. NOZZLE AND HOLDER ASSY

11. Nozzle and Holder

12. Open Pre:MPa(Kqf/cm2)

13. NOZZLE-HOLDER

14. NOZZLE

15. NOZZLE SET

Include in #1:

106675-4660 as INJECTION-PUMP ASSEMBLY

Cross reference number

ZEXEL 106675-4660 1066754660

Zexel num

Bosch num

Firm num

Name

106675-4660
106675-4661

DAEWOO

INJECTION-PUMP ASSEMBLY
D1146TI *

Calibration Data:

Adjustment conditions

Test oil
1404 Test oil ISO4113 or {SAEJ967d}

Test oil temperature degC 40 40 45

Nozzle and nozzle holder 105780-8140

Bosch type code EF8511/9A

Nozzle 105780-0000

Bosch type code DN12SD12T

Nozzle holder 105780-2080

Bosch type code EF8511/9

Opening pressure MPa 17.2

Opening pressure kgf/cm2 175

Injection pipe
Outer diameter - inner diameter - length (mm) mm 8-3-600

Overflow valve 131424-1520

Overflow valve opening pressure kPa 157 123 191

Overflow valve opening pressure kgf/cm2 1.6 1.25 1.95

Tester oil delivery pressure kPa 157 157 157

Tester oil delivery pressure kgf/cm2 1.6 1.6 1.6

Direction of rotation (viewed from drive side)
Right R

Injection timing adjustment

Direction of rotation (viewed from drive side)
Right R

Injection order 1-5-3-6- 2-4

Pre-stroke mm 3.9 3.85 3.95

Beginning of injection position
Governor side NO.1

Difference between angles 1
Cal 1-5 deg. 60 59.5 60.5

Difference between angles 2
Cal 1-3 deg. 120 119.5 120.5

Difference between angles 3
Cal 1-6 deg. 180 179.5 180.5

Difference between angles 4
Cyl.1-2 deg. 240 239.5 240.5

Difference between angles 5
Cal 1-4 deg. 300 299.5 300.5

Injection quantity adjustment

Adjusting point A

Rack position 12

Pump speed r/min 1050 1050 1050

Average injection quantity mm3/st. 169.5 167.5 171.5

Max. variation between cylinders % 0 -2 2

Basic *

Fixing the lever *

Boost pressure kPa 133 133

Boost pressure mmHg 1000 1000

Injection quantity adjustment_02

Adjusting point B

Rack position 6.6+-0.5

Pump speed r/min 315 315 315

Average injection quantity mm3/st. 10 8.7 11.3

Max. variation between cylinders % 0 -15 15

Fixing the rack *

Boost pressure kPa 0 0 0

Boost pressure mmHg 0 0 0

Boost compensator adjustment

Pump speed r/min 500 500 500

Rack position R1-2.2

Boost pressure kPa 20 14.7 25.3

Boost pressure mmHg 150 110 190

Boost compensator adjustment_02

Pump speed r/min 500 500 500

Rack position R1(12)

Boost pressure kPa 120 120 120

Boost pressure mmHg 900 900 900

Test data Ex:

Governor adjustment

N:Pump speed R:Rack position (mm) (1)Target notch: K (2)Tolerance for racks not indicated: +-0.05mm. (3)Set idle sub-spring (4)Main spring setting (5)Boost compensator stroke
----------
K=17
----------

Speed control lever angle

F:Full speed I:Idle (1)Stopper bolt setting
----------

----------
a=15deg+-5deg b=28deg+-5deg

Stop lever angle

N:Pump normal S:Stop the pump. (1)Normal (2)Pump speed aa and rack position bb (to be sealed at delivery) (3)Use the hole above R = cc
----------
aa=0r/min bb=1-0.5mm cc=30mm
----------
a=32deg+-5deg b=70deg+-5deg