106673-2600 ZEXEL 9 400 617 249 BOSCH INJECTION-PUMP ASSEMBLY 9400617249 1066732600 me056906

Information Cross number Calibration Data Calibration Data Ex

Price: query
Buy now
Add to cart Go to cart

Rating:

Buy INJECTION-PUMP ASSEMBLY 106673-2600 zexel genuine, new aftermarket engine parts with delivery

Information injection-pump assembly

BOSCH 9 400 617 249 9400617249

ZEXEL 106673-2600 1066732600

MITSUBISHI ME056906 me056906

Service parts 106673-2600 INJECTION-PUMP ASSEMBLY:

1. _

2. FUEL INJECTION PUMP 106061-5650

3. GOVERNOR 105487-5671

4. SUPPLY PUMP 105207-1330

5. AUTOM. ADVANCE MECHANIS 105636-2200

6. COUPLING PLATE 105662-0710

7. COUPLING PLATE

8. _

9. _

10. NOZZLE AND HOLDER ASSY 105100-7870

11. Nozzle and Holder ME056817

12. Open Pre:MPa(Kqf/cm2) 17.7{180}/21.6{220}

13. NOZZLE-HOLDER 105031-4530

14. NOZZLE 105015-8230

15. NOZZLE SET

Include in #1:

106673-2600 as INJECTION-PUMP ASSEMBLY

Cross reference number

BOSCH 9 400 617 249 9400617249

ZEXEL 106673-2600 1066732600

MITSUBISHI ME056906 me056906

Zexel num

Bosch num

Firm num

Name

106673-2600

9 400 617 249

ME056906 MITSUBISHI

INJECTION-PUMP ASSEMBLY
6D22 K 14CA INJECTION PUMP ASSY PE6P,6PD PE

Calibration Data:

Adjustment conditions

Test oil
1404 Test oil ISO4113 or {SAEJ967d}

Test oil temperature degC 40 40 45

Nozzle and nozzle holder 105780-8140

Bosch type code EF8511/9A

Nozzle 105780-0000

Bosch type code DN12SD12T

Nozzle holder 105780-2080

Bosch type code EF8511/9

Opening pressure MPa 17.2

Opening pressure kgf/cm2 175

Injection pipe
Outer diameter - inner diameter - length (mm) mm 8-3-600

Overflow valve 131424-4620

Overflow valve opening pressure kPa 255 221 289

Overflow valve opening pressure kgf/cm2 2.6 2.25 2.95

Tester oil delivery pressure kPa 157 157 157

Tester oil delivery pressure kgf/cm2 1.6 1.6 1.6

Direction of rotation (viewed from drive side)
Right R

Injection timing adjustment

Direction of rotation (viewed from drive side)
Right R

Injection order 1-5-3-6- 2-4

Pre-stroke mm 4.8 4.75 4.85

Beginning of injection position
Governor side NO.1

Difference between angles 1
Cal 1-5 deg. 60 59.5 60.5

Difference between angles 2
Cal 1-3 deg. 120 119.5 120.5

Difference between angles 3
Cal 1-6 deg. 180 179.5 180.5

Difference between angles 4
Cyl.1-2 deg. 240 239.5 240.5

Difference between angles 5
Cal 1-4 deg. 300 299.5 300.5

Injection quantity adjustment

Adjusting point -

Rack position 8.1

Pump speed r/min 700 700 700

Each cylinder's injection qty mm3/st. 111.5 108.7 114.3

Basic *

Fixing the rack *

Standard for adjustment of the maximum variation between cylinders *

Injection quantity adjustment_02

Adjusting point C

Rack position 5.1+-0.5

Pump speed r/min 225 225 225

Each cylinder's injection qty mm3/st. 10 8.5 11.5

Fixing the rack *

Standard for adjustment of the maximum variation between cylinders *

Injection quantity adjustment_03

Adjusting point A

Rack position R1(8.1)

Pump speed r/min 700 700 700

Average injection quantity mm3/st. 111.5 110.5 112.5

Basic *

Fixing the lever *

Injection quantity adjustment_04

Adjusting point E

Rack position -

Pump speed r/min 100 100 100

Average injection quantity mm3/st. 130 110 150

Fixing the lever *

Remarks
After startup boost setting

Timer adjustment

Pump speed r/min 850--

Advance angle deg. 0 0 0

Remarks
Start

Timer adjustment_02

Pump speed r/min 800

Advance angle deg. 0.5

Timer adjustment_03

Pump speed r/min 1100

Advance angle deg. 3 2.5 3.5

Remarks
Finish

Test data Ex:

Governor adjustment

N:Pump speed R:Rack position (mm) (1)Lever ratio: RT (2)Target shim dimension: TH (3)Tolerance for racks not indicated: +-0.05mm. (4)Excess fuel setting for starting: SXL (5)Damper spring setting
----------
RT=1 TH=1.8mm SXL=9.25+-0.1mm
----------

Speed control lever angle

F:Full speed
----------

----------
a=(16deg)+-5deg

0000000901

F:Full load I:Idle (1)Stopper bolt setting (2)Use the hole at R = aa
----------
aa=55mm
----------
a=23deg+-3deg b=24deg+-5deg

Stop lever angle

S:Stop the pump. (1)Free (at delivery) (2)Rack position = aa (3)Stopper bolt setting (4)Drive side
----------
aa=3-0.5mm
----------
a=25deg+-5deg b=59deg+7deg-5deg

0000001501 MICRO SWITCH

Adjustment of the micro-switch Adjust the bolt to obtain the following lever position when the micro-switch is ON. (1)Speed N1 (2)Rack position Ra
----------
N1=325r/min Ra=4.8+-0.1mm
----------

0000001601 LEVER

(1)Viewed from top of pump. (2)Pump side (3)Load control lever (4)Adjusting bolt (5)Nut 1. Idle increase link mechanism adjustment (1)After completing pump and governor adjustment, fix the load control lever in the idle position. (2)Adjust using the bolt (4) so that the idle-increase link mechanism's lever angle is a, then fix using the nut (5).
----------

----------
a=2deg+-3deg

Timing setting

(1)Pump vertical direction (2)Coupling's key groove position at No 1 cylinder's beginning of injection (3)B.T.D.C.: aa (4)-
----------
aa=12deg
----------
a=(7deg)