106671-3750 ZEXEL INJECTION-PUMP ASSEMBLY Calibration Data 1066713750 220004420a


106671-3750 INJECTION-PUMP ASSEMBLY
Rating:
12
Buy INJECTION-PUMP ASSEMBLY 106671-3750 zexel genuine, new aftermarket engine parts with delivery

Information injection-pump assembly

ZEXEL 106671-3750 1066713750
HINO 220004420A 220004420a

Cross reference number

ZEXEL 106671-3750 1066713750
HINO 220004420A 220004420a


Zexel num
Bosch num
Firm num
Name
106671-3750 
106671-3751 
 
220004420A  HINO
INJECTION-PUMP ASSEMBLY
EK100 *

Calibration Data:

Adjustment conditions
Test oil
1404 Test oil
  ISO4113 or {SAEJ967d}
Test oil temperature degC   40 40 45
Nozzle and nozzle holder   105780-8140
Bosch type code   EF8511/9A
Nozzle   105780-0000
Bosch type code   DN12SD12T
Nozzle holder   105780-2080
Bosch type code   EF8511/9
Opening pressure MPa   17.2
Opening pressure kgf/cm2   175
Injection pipe
Outer diameter - inner diameter - length (mm)
mm   8-3-600
Overflow valve   134424-0920
Overflow valve opening pressure kPa   162 147 177
Overflow valve opening pressure kgf/cm2   1.65 1.5 1.8
Tester oil delivery pressure kPa   157 157 157
Tester oil delivery pressure kgf/cm2   1.6 1.6 1.6
Direction of rotation (viewed from drive side)
Left
  L
Injection timing adjustment
Direction of rotation (viewed from drive side)
Left
  L
Injection order   1-4-2-6- 3-5
Pre-stroke mm   3.3 3.2 3.3
Beginning of injection position
Drive side
  NO.1
Difference between angles 1
Cal 1-4
deg.   60 59.5 60.5
Difference between angles 2
Cyl.1-2
deg.   120 119.5 120.5
Difference between angles 3
Cal 1-6
deg.   180 179.5 180.5
Difference between angles 4
Cal 1-3
deg.   240 239.5 240.5
Difference between angles 5
Cal 1-5
deg.   300 299.5 300.5
Injection quantity adjustment
Adjusting point   A
Rack position   10.6
Pump speed r/min   500 500 500
Average injection quantity mm3/st.   128.5 125.5 131.5
Max. variation between cylinders %   0 -4 4
Fixing the lever   *
Injection quantity adjustment_02
Adjusting point   B
Rack position   10.7+-0. 5
Pump speed r/min   700 700 700
Average injection quantity mm3/st.   134.7 132.7 136.7
Max. variation between cylinders %   0 -2 2
Basic   *
Fixing the lever   *
Injection quantity adjustment_03
Adjusting point   C
Rack position   11.2+-0. 5
Pump speed r/min   1150 1150 1150
Average injection quantity mm3/st.   143.7 140.7 146.7
Max. variation between cylinders %   0 -4 4
Fixing the lever   *
Injection quantity adjustment_04
Adjusting point   D
Rack position   7+-0.5
Pump speed r/min   225 225 225
Average injection quantity mm3/st.   15 12 18
Max. variation between cylinders %   0 -15 15
Fixing the rack   *
Injection quantity adjustment_05
Adjusting point   E
Rack position   -
Pump speed r/min   100 100 100
Average injection quantity mm3/st.   126.3 119.3 133.3
Fixing the lever   *
Timer adjustment
Pump speed r/min   700+-50
Advance angle deg.   0 0 0
Remarks
Start
 
Timer adjustment_02
Pump speed r/min   900
Advance angle deg.   1.4 0.9 1.9
Timer adjustment_03
Pump speed r/min   1150
Advance angle deg.   4 3.5 4.5
Remarks
Finish
 

Test data Ex:

Governor adjustment

Test data 106671-3750
N:Pump speed R:Rack position (mm) (1)Damper spring setting: DL (2)RACK LIMIT
----------
DL=6.2-0.2mm
----------

Speed control lever angle

Test data 106671-3750
F:Full speed
----------

----------
a=3deg+-5deg

0000000901

Test data 106671-3750
F:Full load I:Idle (1)Stopper bolt setting
----------

----------
a=10deg+-5deg b=27.5deg+-3deg

Stop lever angle

Test data 106671-3750
N:Pump normal S:Stop the pump.
----------

----------
a=15deg+-5deg b=64deg+-5deg

0000001501 GOVERNOR TORQUE CONTROL

Test data 106671-3750
Dr:Torque control stroke (A): Without torque control spring capsule 1. Adjustment procedures (1)Procedure is the same as that for the RFD (former type), except that the positive torque control stroke must be determined at the full lever setting. 2. Procedures for adjustment (1)Remove the torque control spring capsule. (2)Operate the pump at approximately N1. (End of idling spring operation < N1.) (3)Tilt the lever to the full side. (4)Set so that R = RF. (5)Increase the speed by pushing in the screw (attached to the bracket on the rear of the tension lever) through the adjusting window. (6)Adjust so that the torque control stroke Dr1 can be obtained. (7)Align N2 and N3 with the torque control spring capsule. 3. Final confirmation (1)After final confirmation, temporarily set the load lever to N = N1, R = idling position. (2)From this condition, increase speed to N = N4. (3)Confirm that positive torque control stroke is Dr2.
----------
N1=500r/min N2=(540)+-30r/min N3=(980)+-50r/min N4=1100r/min RF=10.6mm Dr1=0.6mm Dr2=0+0.3mm
----------

Timing setting

Test data 106671-3750
(1)Pump vertical direction (2)Coupling's key groove position at No 1 cylinder's beginning of injection (3)- (4)-
----------

----------
a=(0deg)




Have questions with 106671-3750?





Group cross 106671-3750 ZEXEL

Hino 

 
220004330A 
INJECTION-PUMP ASSEMBLY
EK100
 
220004330B 
INJECTION-PUMP ASSEMBLY
EK100
9 400 612 075 
220004331A 
INJECTION-PUMP ASSEMBLY
EK100
9 400 616 778 
220004331B 
INJECTION-PUMP ASSEMBLY
EK100
 
220001553A 
INJECTION-PUMP ASSEMBLY
EK100
 
220002352A 
INJECTION-PUMP ASSEMBLY
EK100
 
220003688A 
INJECTION-PUMP ASSEMBLY
EK100
 
220004221A 
INJECTION-PUMP ASSEMBLY
EK200
 
220004221B 
INJECTION-PUMP ASSEMBLY
EK200
 
220004222A 
INJECTION-PUMP ASSEMBLY
EK200
9 400 616 779 
220004222B 
INJECTION-PUMP ASSEMBLY
EK200
106671-3750  

106671-3751 
 
220004420A 
INJECTION-PUMP ASSEMBLY
EK100
9 400 616 780 
220004421A 
INJECTION-PUMP ASSEMBLY
EK100
 
220004300B 
INJECTION-PUMP ASSEMBLY
EK100
 
220004301A 
INJECTION-PUMP ASSEMBLY
EK100
 
220004302A 
INJECTION-PUMP ASSEMBLY
EK100
 
220004440A 
INJECTION-PUMP ASSEMBLY
EK200
 
220004441A 
INJECTION-PUMP ASSEMBLY
EK200
 
220004441B 
INJECTION-PUMP ASSEMBLY
EK200
9 400 616 781 
220004441C 
INJECTION-PUMP ASSEMBLY
EK200
 
220004291B 
INJECTION-PUMP ASSEMBLY
EK100
 
220004292A 
INJECTION-PUMP ASSEMBLY
EK100
 
220201862A 
INJECTION-PUMP ASSEMBLY
EP100
 
220201863A 
INJECTION-PUMP ASSEMBLY
EP100
 
220201864A 
INJECTION-PUMP ASSEMBLY
EP100T
9 400 610 044 
220201864B 
INJECTION-PUMP ASSEMBLY
EP100T
Back to top