106671-2770 ZEXEL INJECTION-PUMP ASSEMBLY Calibration Data 1066712770 me056376

Information Cross number Calibration Data Calibration Data Ex

Price: query
Buy now
Add to cart Go to cart

Rating:

Buy INJECTION-PUMP ASSEMBLY 106671-2770 zexel genuine, new aftermarket engine parts with delivery

Information injection-pump assembly

ZEXEL 106671-2770 1066712770

MITSUBISHI ME056376 me056376

Cross reference number

ZEXEL 106671-2770 1066712770

MITSUBISHI ME056376 me056376

Zexel num

Bosch num

Firm num

Name

106671-2770

ME056376 MITSUBISHI

INJECTION-PUMP ASSEMBLY
6D23 * K

Calibration Data:

Adjustment conditions

Test oil
1404 Test oil ISO4113 or {SAEJ967d}

Test oil temperature degC 40 40 45

Nozzle and nozzle holder 105780-8140

Bosch type code EF8511/9A

Nozzle 105780-0000

Bosch type code DN12SD12T

Nozzle holder 105780-2080

Bosch type code EF8511/9

Opening pressure MPa 17.2

Opening pressure kgf/cm2 175

Injection pipe
Outer diameter - inner diameter - length (mm) mm 8-3-600

Overflow valve opening pressure kPa 255 221 289

Overflow valve opening pressure kgf/cm2 2.6 2.25 2.95

Tester oil delivery pressure kPa 157 157 157

Tester oil delivery pressure kgf/cm2 1.6 1.6 1.6

Direction of rotation (viewed from drive side)
Right R

Injection timing adjustment

Direction of rotation (viewed from drive side)
Right R

Injection order 1-5-3-6- 2-4

Pre-stroke mm 4.8 4.75 4.85

Beginning of injection position
Governor side NO.1

Difference between angles 1
Cal 1-5 deg. 60 59.5 60.5

Difference between angles 2
Cal 1-3 deg. 120 119.5 120.5

Difference between angles 3
Cal 1-6 deg. 180 179.5 180.5

Difference between angles 4
Cyl.1-2 deg. 240 239.5 240.5

Difference between angles 5
Cal 1-4 deg. 300 299.5 300.5

Injection quantity adjustment

Adjusting point -

Rack position 7.6

Pump speed r/min 700 700 700

Each cylinder's injection qty mm3/st. 97 94.2 99.8

Basic *

Fixing the rack *

Standard for adjustment of the maximum variation between cylinders *

Injection quantity adjustment_02

Adjusting point F

Rack position 5+-0.5

Pump speed r/min 500 500 500

Each cylinder's injection qty mm3/st. 16.5 14 19

Fixing the rack *

Standard for adjustment of the maximum variation between cylinders *

Injection quantity adjustment_03

Adjusting point A

Rack position R1(7.6)

Pump speed r/min 700 700 700

Average injection quantity mm3/st. 97 96 98

Fixing the lever *

Injection quantity adjustment_04

Adjusting point B

Rack position R1(7.6)

Pump speed r/min 1100 1100 1100

Average injection quantity mm3/st. 111 107 115

Difference in delivery mm3/st. 8 8 8

Fixing the lever *

Injection quantity adjustment_05

Adjusting point C

Rack position 5.7+-0.5

Pump speed r/min 225 225 225

Each cylinder's injection qty mm3/st. 16.5 13.7 19.3

Fixing the rack *

Remarks
(check)

Injection quantity adjustment_06

Adjusting point E

Rack position -

Pump speed r/min 100 100 100

Average injection quantity mm3/st. 115 95 135

Fixing the lever *

Timer adjustment

Pump speed r/min 950

Advance angle deg. 0.5

Timer adjustment_02

Pump speed r/min 1050

Advance angle deg. 2.2 1.7 2.7

Timer adjustment_03

Pump speed r/min 1150

Advance angle deg. 5.5 5 6

Remarks
Finish

Test data Ex:

Governor adjustment

N:Pump speed R:Rack position (mm) (1)Beginning of damper spring operation: DL (2)Excess fuel setting for starting: SXL
----------
DL=4.5-0.2mm SXL=R1(7.6)+0.2mm
----------

Speed control lever angle

F:Full speed
----------

----------
a=28deg+-5deg

0000000901

F:Full load I:Idle (1)At idle increase (2)Stopper bolt setting
----------

----------
a=29deg+-5deg b=23deg+-3deg c=5deg

Stop lever angle

N:Pump normal S:Stop the pump.
----------

----------
a=6deg+-5deg b=64deg+-5deg

0000001501 MICRO SWITCH

Adjustment of the micro-switch Adjust the bolt to obtain the following lever position when the micro-switch is ON. (1)Speed N1 (2)Rack position Ra
----------
N1=325+-0.5r/min Ra=5.4mm
----------

0000001601 LEVER

1. Idle increase mechanism adjustment procedure (1)Set lever (a) in the idle position. (2)Move the lever (A) a from the idle set position to the full side. (Temporarily fixed for adjustment.) (3)Adjust using screw (c) so that lever (B) contacts lever (A). (4)Turn screw (c) and fix it using the nut where the hole above aa moves from horizontal to position b.
----------
a=5deg b=25+-5deg c=50mm
----------