101901-0810 ZEXEL INJECTION-PUMP ASSEMBLY Calibration Data 1019010810 1156007492

Information Cross number Calibration Data Calibration Data Ex

Price: query
Buy now
Add to cart Go to cart

Rating:

Buy INJECTION-PUMP ASSEMBLY 101901-0810 zexel genuine, new aftermarket engine parts with delivery

Information injection-pump assembly

ZEXEL 101901-0810 1019010810

ISUZU 1156007492 1156007492

Cross reference number

ZEXEL 101901-0810 1019010810

ISUZU 1156007492 1156007492

Zexel num

Bosch num

Firm num

Name

101901-0810

1156007492 ISUZU

INJECTION-PUMP ASSEMBLY
8PB1 * K

Calibration Data:

Adjustment conditions

Test oil
1404 Test oil ISO4113 or {SAEJ967d}

Test oil temperature degC 40 40 45

Nozzle and nozzle holder 105780-8140

Bosch type code EF8511/9A

Nozzle 105780-0000

Bosch type code DN12SD12T

Nozzle holder 105780-2080

Bosch type code EF8511/9

Opening pressure MPa 17.2

Opening pressure kgf/cm2 175

Injection pipe
Outer diameter - inner diameter - length (mm) mm 6-2-600

Overflow valve 134424-0020

Overflow valve opening pressure kPa 157 123 191

Overflow valve opening pressure kgf/cm2 1.6 1.25 1.95

Tester oil delivery pressure kPa 157 157 157

Tester oil delivery pressure kgf/cm2 1.6 1.6 1.6

Direction of rotation (viewed from drive side)
Right R

Injection timing adjustment

Direction of rotation (viewed from drive side)
Right R

Injection order
R: right hand row, L: left hand row L1-R8-L7 -L3-R6-L 5-R4-R2

Pre-stroke mm 3.2 3.15 3.25

Beginning of injection position
Opposite to the driving side NO.1

Difference between angles 1
Cal 1-8 deg. 45 44.5 45.5

Difference between angles 2
Cal 1-7 deg. 90 89.5 90.5

Difference between angles 3
Cal 1-3 deg. 135 134.5 135.5

Difference between angles 4
Cal 1-6 deg. 180 179.5 180.5

Difference between angles 5
Cal 1-5 deg. 225 224.5 225.5

Difference between angles 6
Cal 1-4 deg. 270 269.5 270.5

Difference between angles 7
Cyl.1-2 deg. 315 314.5 315.5

Injection quantity adjustment

Adjusting point A

Rack position 11.7

Pump speed r/min 1350 1350 1350

Average injection quantity mm3/st. 90 88 92

Max. variation between cylinders % 0 -4 4

Fixing the lever *

Injection quantity adjustment_02

Adjusting point B

Rack position 11.7

Pump speed r/min 700 700 700

Average injection quantity mm3/st. 84 83 85

Max. variation between cylinders % 0 -2 2

Basic *

Fixing the lever *

Timer adjustment

Pump speed r/min 1050+-50

Advance angle deg. 0 0 0

Remarks
Start

Timer adjustment_02

Pump speed r/min 1150

Advance angle deg. 1.4 0.9 1.9

Timer adjustment_03

Pump speed r/min 1250

Advance angle deg. 3 2.5 3.5

Timer adjustment_04

Pump speed r/min 1350

Advance angle deg. 5 4.5 5.5

Remarks
Finish

Test data Ex:

Governor adjustment

N:Pump speed R:Rack position (mm) (1)Target notch: K (2)Deliver with rack limit not operating (3)RACK CAP: R1
----------
K=5 R1=(17.5)mm
----------

Speed control lever angle

F:Full speed I:Idle D:Dead point (1)Stopper bolt setting
----------

----------
a=(20deg+-3deg) b=33deg+-5deg c=3deg+3deg

0000001501 LEVER

1. Variable lever adjustment (1)Fix lever (B) in the idle position using bolts (C) and (D). (2)Temporarily fix the lever (A) in the center of the elongated hole. (3)Set the dead point position temporarily and measure the lever angle. (4)Fix the lever (A) at the idle lever angle position using the bolt (E). (5)Lock using bolt (G). (6)After completing idle adjustment, loosen the full side stopper bolt (D). (7)Move the lever (A) in the full speed direction. (8)Fix bolt (D) at full speed position. (9)Finally, measure the lever angle and set the idle stopper bolt (C) stop position.
----------

----------