101606-1730 ZEXEL INJECTION-PUMP ASSEMBLY Calibration Data 1016061730


101606-1730 INJECTION-PUMP ASSEMBLY
Rating:
68
Buy INJECTION-PUMP ASSEMBLY 101606-1730 zexel genuine, new aftermarket engine parts with delivery

Information injection-pump assembly

ZEXEL 101606-1730 1016061730

Cross reference number

ZEXEL 101606-1730 1016061730


Zexel num
Bosch num
Firm num
Name
101606-1730 
101606-1731 
 
  MITSUBISHI
INJECTION-PUMP ASSEMBLY
6D14T *

Calibration Data:

Adjustment conditions
Test oil
1404 Test oil
  ISO4113 or {SAEJ967d}
Test oil temperature degC   40 40 45
Nozzle and nozzle holder   105780-8140
Bosch type code   EF8511/9A
Nozzle   105780-0000
Bosch type code   DN12SD12T
Nozzle holder   105780-2080
Bosch type code   EF8511/9
Opening pressure MPa   17.2
Opening pressure kgf/cm2   175
Injection pipe
Outer diameter - inner diameter - length (mm)
mm   6-2-600
Overflow valve   131424-5520
Overflow valve opening pressure kPa   255 221 289
Overflow valve opening pressure kgf/cm2   2.6 2.25 2.95
Tester oil delivery pressure kPa   157 157 157
Tester oil delivery pressure kgf/cm2   1.6 1.6 1.6
Direction of rotation (viewed from drive side)
Left
  L
Injection timing adjustment
Direction of rotation (viewed from drive side)
Left
  L
Injection order   1-5-3-6- 2-4
Pre-stroke mm   3 2.95 3.05
Beginning of injection position
Governor side
  NO.1
Difference between angles 1
Cal 1-5
deg.   60 59.5 60.5
Difference between angles 2
Cal 1-3
deg.   120 119.5 120.5
Difference between angles 3
Cal 1-6
deg.   180 179.5 180.5
Difference between angles 4
Cyl.1-2
deg.   240 239.5 240.5
Difference between angles 5
Cal 1-4
deg.   300 299.5 300.5
Injection quantity adjustment
Adjusting point   -
Rack position   12.1
Pump speed r/min   800 800 800
Each cylinder's injection qty mm3/st.   88 85.4 90.6
Basic   *
Fixing the rack   *
Standard for adjustment of the maximum variation between cylinders   *
Injection quantity adjustment_02
Adjusting point   H
Rack position   9.5+-0.5
Pump speed r/min   275 275 275
Each cylinder's injection qty mm3/st.   10.5 9 12
Fixing the rack   *
Standard for adjustment of the maximum variation between cylinders   *
Injection quantity adjustment_03
Adjusting point   A
Rack position   R1(12.1)
Pump speed r/min   800 800 800
Average injection quantity mm3/st.   88 87 89
Basic   *
Fixing the lever   *
Boost pressure kPa   49.3 49.3
Boost pressure mmHg   370 370
Injection quantity adjustment_04
Adjusting point   C
Rack position   (R1-0.8)
Pump speed r/min   600 600 600
Average injection quantity mm3/st.   67 65 69
Fixing the lever   *
Boost pressure kPa   18.7 18.7
Boost pressure mmHg   140 140
Injection quantity adjustment_05
Adjusting point   I
Rack position   -
Pump speed r/min   100 100 100
Average injection quantity mm3/st.   110 90 130
Fixing the lever   *
Rack limit   *
Boost compensator adjustment
Pump speed r/min   600 600 600
Rack position   R1-1.1
Boost pressure kPa   13.3 13.3 13.3
Boost pressure mmHg   100 100 100
Boost compensator adjustment_02
Pump speed r/min   600 600 600
Rack position   (R1-0.8)
Boost pressure kPa   18.7 17.4 20
Boost pressure mmHg   140 130 150
Boost compensator adjustment_03
Pump speed r/min   600 600 600
Rack position   R1(12.1)
Boost pressure kPa   36 29.3 42.7
Boost pressure mmHg   270 220 320
Timer adjustment
Pump speed r/min   1250--
Advance angle deg.   0 0 0
Remarks
Start
 
Timer adjustment_02
Pump speed r/min   1200
Advance angle deg.   0.5
Timer adjustment_03
Pump speed r/min   1300
Advance angle deg.   1.6 1.1 2.1
Timer adjustment_04
Pump speed r/min   1400
Advance angle deg.   3.5 3 4
Remarks
Finish
 

Test data Ex:

Governor adjustment

Test data 101606-1730
N:Pump speed R:Rack position (mm) (1)Torque cam stamping: T1 (2)RACK LIMIT (3)Boost compensator stroke: BCL
----------
T1=B45 BCL=1.1+-0.1mm
----------

Speed control lever angle

Test data 101606-1730
F:Full speed I:Idle (1)Use the hole at R = aa (2)Stopper bolt set position 'H'
----------
aa=40mm
----------
a=18.5deg+-5deg b=(46deg)+-3deg

Stop lever angle

Test data 101606-1730
N:Engine manufacturer's normal use S:Stop the pump. (1)Set the stopper bolt at pump speed = aa and rack position = bb (non-injection rack position). Confirm non-injection. (2)After setting the stopper bolt, confirm non-injection at speed cc. Rack position = dd (non-injection rack position). (3)Rack position = approximately ee. (4)Free (at shipping) (5)At hole above R = ff.
----------
aa=1550r/min bb=(7.5)mm cc=275r/min dd=(9)mm ee=17.4mm ff=50mm
----------
a=38.5deg+-5deg b=(27deg) c=17deg+-5deg

0000001201

Test data 101606-1730
I:Idle F:At operation, hold it in the full speed position. (1)Rack position = aa, speed = bb.
----------
aa=8.4mm bb=1490r/min
----------
a=15deg+-5deg b=(41deg)+-3deg

0000001501 MICRO SWITCH

Adjustment of the micro-switch Adjust the bolt to obtain the following lever position when the micro-switch is ON. (1)Speed N1 (2)Rack position Ra
----------
N1=400+-5r/min Ra=9.2mm
----------

Timing setting

Test data 101606-1730
(1)Pump vertical direction (2)Position of timer's tooth at No 1 cylinder's beginning of injection (3)B.T.D.C.: aa (4)-
----------
aa=15deg
----------
a=(0deg)




Have questions with 101606-1730?





Group cross 101606-1730 ZEXEL

Mitsubishi 

F 019 Z20 474 
ME076242 
INJECTION-PUMP ASSEMBLY
6D16
9 400 615 464 
ME076246 
INJECTION-PUMP ASSEMBLY
6D16T
101606-1730  

101606-1731 
 
 
INJECTION-PUMP ASSEMBLY
6D14T
 
ME076209 
INJECTION-PUMP ASSEMBLY
6D14T
 
 
INJECTION-PUMP ASSEMBLY
6D16T
 
ME076211 
INJECTION-PUMP ASSEMBLY
6D16T
 
 
INJECTION-PUMP ASSEMBLY
6D15
 
ME035492 
INJECTION-PUMP ASSEMBLY
6D15
9 400 615 465 
ME056729 
INJECTION-PUMP ASSEMBLY
6D22
9 400 615 466 
ME047505 
INJECTION-PUMP ASSEMBLY
6D16T
9 400 619 989 
ME076257 
INJECTION-PUMP ASSEMBLY
6D16
 
 
INJECTION-PUMP ASSEMBLY
6D31T
9 400 615 467 
ME086566 
INJECTION-PUMP ASSEMBLY
6D31T
Back to top