101606-0211 ZEXEL INJECTION-PUMP ASSEMBLY Calibration Data 1016060211 8943922192


101606-0211 INJECTION-PUMP ASSEMBLY
Rating:
16
Buy INJECTION-PUMP ASSEMBLY 101606-0211 zexel genuine, new aftermarket engine parts with delivery

Information injection-pump assembly

ZEXEL 101606-0211 1016060211
ISUZU 8943922192 8943922192

Cross reference number

ZEXEL 101606-0211 1016060211
ISUZU 8943922192 8943922192


Zexel num
Bosch num
Firm num
Name
101606-0211 
101606-0212 
 
8943922192  ISUZU
INJECTION-PUMP ASSEMBLY
6HH1 * K

Calibration Data:

Adjustment conditions
Test oil
1404 Test oil
  ISO4113 or {SAEJ967d}
Test oil temperature degC   40 40 45
Nozzle and nozzle holder   105780-8260
Bosch type code   9 430 610 133
Nozzle   105780-0120
Bosch type code   1 688 901 990
Nozzle holder   105780-2190
Opening pressure MPa   18
Opening pressure kgf/cm2   184
Injection pipe
Outer diameter - inner diameter - length (mm)
mm   6-2-600
Overflow valve   131424-8620
Overflow valve opening pressure kPa   206 172 240
Overflow valve opening pressure kgf/cm2   2.1 1.75 2.45
Tester oil delivery pressure kPa   255 255 255
Tester oil delivery pressure kgf/cm2   2.6 2.6 2.6
Direction of rotation (viewed from drive side)
Left
  L
Injection timing adjustment
Direction of rotation (viewed from drive side)
Left
  L
Injection order   1-5-3-6- 2-4
Pre-stroke mm   3.8 3.75 3.85
Rack position
Point A
  R=A
Beginning of injection position
Governor side
  NO.1
Difference between angles 1
Cal 1-5
deg.   60 59.5 60.5
Difference between angles 2
Cal 1-3
deg.   120 119.5 120.5
Difference between angles 3
Cal 1-6
deg.   180 179.5 180.5
Difference between angles 4
Cyl.1-2
deg.   240 239.5 240.5
Difference between angles 5
Cal 1-4
deg.   300 299.5 300.5
Injection quantity adjustment
Adjusting point   -
Rack position   14.1
Pump speed r/min   850 850 850
Average injection quantity mm3/st.   126 124.4 127.6
Max. variation between cylinders %   0 -2.5 2.5
Basic   *
Fixing the rack   *
Standard for adjustment of the maximum variation between cylinders   *
Injection quantity adjustment_02
Adjusting point   Z
Rack position   9.5+-0.5
Pump speed r/min   300 300 300
Average injection quantity mm3/st.   15.5 14.2 16.8
Max. variation between cylinders %   0 -14 14
Fixing the rack   *
Standard for adjustment of the maximum variation between cylinders   *
Injection quantity adjustment_03
Adjusting point   A
Rack position   R1(14.1)
Pump speed r/min   850 850 850
Average injection quantity mm3/st.   126 125 127
Basic   *
Fixing the lever   *
Injection quantity adjustment_04
Adjusting point   B
Rack position   (R1+1.55 )+0.05-0 .15
Pump speed r/min   1425 1425 1425
Average injection quantity mm3/st.   137.5 134.3 140.7
Fixing the lever   *

Test data Ex:

Governor adjustment

Test data 101606-0211
N:Pump speed R:Rack position (mm) (1)Torque cam stamping: T1 (2)Tolerance for racks not indicated: +-0.05mm.
----------
T1=N91
----------

Timer adjustment

Test data 101606-0211
(1)Adjusting range (2)Step response time (N): Speed of the pump (L): Load (theta) Advance angle (Srd1) Step response time 1 (Srd2) Step response time 2 1. Adjusting conditions for the variable timer (1)Adjust the clearance between the pickup and the protrusion to L.
----------
L=1.5+-0.2mm N2=800r/min C2=(8)deg t1=2--sec. t2=2--sec.
----------
N1=1300++r/min P1=0kPa(0kgf/cm2) P2=392kPa(4kgf/cm2) C1=8+-0.3deg R01=0/4load R02=4/4load

Speed control lever angle

Test data 101606-0211
F:Full speed I:Idle (1)Stopper bolt set position 'H' (2)Use the pin at R = aa (3)Viewed from feed pump side.
----------
aa=35mm
----------
a=10deg+-5deg b=40.5deg+-3deg

Stop lever angle

Test data 101606-0211
N:Pump normal S:Stop the pump. (1)Use the pin at R = aa
----------
aa=45mm
----------
a=12.5deg+-5deg b=40deg+-5deg

0000001501 RACK SENSOR

Test data 101606-0211
Rack sensor adjustment 1. Flange type rack sensor (rack sensor adjustment -5*20) (1)These types of rack sensors do not need adjustment. Confirm the performance with the following procedures. (2)Mount the rack sensor main body to the pump main body. (3)Fix the pump lever at full. (4)At supply voltage V1, pump speed N1 and rack position Ra, confirm that the amp's output voltage is Vist. (5)Move the pump lever two or three times. (6)Set again to full. (7)Confirm that the amplifier output voltage is Vist. (8)Fix the caution plate to the upper part of the rack sensor. (For those without the caution plate instructions, make sure the nameplate of the rack sensor carries the "Don't hold here" caution.) (9)Apply red paint to the rack sensor mounting bolts (2 places).
----------
V1=5+-0.01V N1=850r/min Ra=R1(14.1)mm Vist=3.55+-0.28V
----------

Timing setting

Test data 101606-0211
(1)Pump vertical direction (2)Positions of coupling's threaded installation holes at No 1 cylinder's beginning of injection (3)B.T.D.C.: aa (4)-
----------
aa=6deg
----------
a=(160deg)




Have questions with 101606-0211?





Group cross 101606-0211 ZEXEL

Isuzu 

9 400 615 409 
8976004970 
INJECTION-PUMP ASSEMBLY
6HH1-S
 
 
INJECTION-PUMP ASSEMBLY

Isuzu 

101606-0211  

101606-0212 
 
8943922192 
INJECTION-PUMP ASSEMBLY
6HH1
9 400 612 115 
8943922193 
INJECTION-PUMP ASSEMBLY
6HH1
9 400 611 260 
8976006300 
INJECTION-PUMP ASSEMBLY
6HH1
9 400 615 410 
1156033580 
INJECTION-PUMP ASSEMBLY
6BG1-T
9 400 612 263 
1156034120 
INJECTION-PUMP ASSEMBLY
6BG1MTCX
9 400 612 533 
1156034121 
INJECTION-PUMP ASSEMBLY
6BG1MTCX
9 400 612 657 
1156034122 
INJECTION-PUMP ASSEMBLY
6BG1MTCX
9 400 612 206 
1156034190 
INJECTION-PUMP ASSEMBLY
6BG1-T
9 400 615 411 
8976019390 
INJECTION-PUMP ASSEMBLY
6HL1-N
9 400 615 412 
8976019400 
INJECTION-PUMP ASSEMBLY
6HL1-N
9 400 615 413 
8976019410 
INJECTION-PUMP ASSEMBLY
6HL1-N
9 400 615 414 
8976019420 
INJECTION-PUMP ASSEMBLY
6HL1-N
Back to top