101603-1730 ZEXEL INJECTION-PUMP ASSEMBLY Calibration Data 1016031730 me038814

Information Cross number Calibration Data Calibration Data Ex

Price: query
Buy now
Add to cart Go to cart

Rating:

Buy INJECTION-PUMP ASSEMBLY 101603-1730 zexel genuine, new aftermarket engine parts with delivery

Information injection-pump assembly

ZEXEL 101603-1730 1016031730

MITSUBISHI ME038814 me038814

Service parts 101603-1730 INJECTION-PUMP ASSEMBLY:

1. _

2. FUEL INJECTION PUMP 101060-9610

3. GOVERNOR 105412-1930

4. SUPPLY PUMP 105210-4640

5. AUTOM. ADVANCE MECHANIS 105643-5060

6. COUPLING PLATE

7. COUPLING PLATE

8. _

9. _

10. NOZZLE AND HOLDER ASSY 105100-5261

11. Nozzle and Holder

12. Open Pre:MPa(Kqf/cm2) 21.6(220)

13. NOZZLE-HOLDER 105030-4990

14. NOZZLE 105015-4860

15. NOZZLE SET

Include in #1:

101603-1730 as INJECTION-PUMP ASSEMBLY

101603-8071 as _

Cross reference number

ZEXEL 101603-1730 1016031730

MITSUBISHI ME038814 me038814

Zexel num

Bosch num

Firm num

Name

101603-1730

ME038814 MITSUBISHI

INJECTION-PUMP ASSEMBLY
6D14T * K

Calibration Data:

Adjustment conditions

Test oil
1404 Test oil ISO4113 or {SAEJ967d}

Test oil temperature degC 40 40 45

Nozzle and nozzle holder 105780-8140

Bosch type code EF8511/9A

Nozzle 105780-0000

Bosch type code DN12SD12T

Nozzle holder 105780-2080

Bosch type code EF8511/9

Opening pressure MPa 17.2

Opening pressure kgf/cm2 175

Injection pipe
Outer diameter - inner diameter - length (mm) mm 6-2-600

Overflow valve 131424-3720

Overflow valve opening pressure kPa 255 221 289

Overflow valve opening pressure kgf/cm2 2.6 2.25 2.95

Tester oil delivery pressure kPa 157 157 157

Tester oil delivery pressure kgf/cm2 1.6 1.6 1.6

Direction of rotation (viewed from drive side)
Left L

Injection timing adjustment

Direction of rotation (viewed from drive side)
Left L

Injection order 1-5-3-6- 2-4

Pre-stroke mm 3 2.95 3.05

Beginning of injection position
Governor side NO.1

Difference between angles 1
Cal 1-5 deg. 60 59.5 60.5

Difference between angles 2
Cal 1-3 deg. 120 119.5 120.5

Difference between angles 3
Cal 1-6 deg. 180 179.5 180.5

Difference between angles 4
Cyl.1-2 deg. 240 239.5 240.5

Difference between angles 5
Cal 1-4 deg. 300 299.5 300.5

Injection quantity adjustment

Adjusting point A

Rack position 9.5

Pump speed r/min 1400 1400 1400

Average injection quantity mm3/st. 79.6 78.6 80.6

Max. variation between cylinders % 0 -2.5 2.5

Basic *

Fixing the lever *

Injection quantity adjustment_02

Adjusting point B

Rack position 8+-0.5

Pump speed r/min 375 375 375

Average injection quantity mm3/st. 17.4 14.8 20

Max. variation between cylinders % 0 -15 15

Fixing the rack *

Timer adjustment

Pump speed r/min 1200--

Advance angle deg. 0 0 0

Remarks
Start

Timer adjustment_02

Pump speed r/min 1150

Advance angle deg. 0.5

Timer adjustment_03

Pump speed r/min 1300

Advance angle deg. 2 1.5 2.5

Timer adjustment_04

Pump speed r/min 1400

Advance angle deg. 3.5 3 4

Remarks
Finish

Test data Ex:

Governor adjustment

N:Pump speed R:Rack position (mm) (1)Target notch: K (2)Torque spring does not operate. (3)Set at delivery (4)Main spring setting (5)Set idle sub-spring
----------
K=12
----------

Speed control lever angle

F:Full speed I:Idle (1)Stopper bolt setting (2)At shipping
----------

----------
a=30deg+-5deg b=(2deg) c=15deg+-5deg

Stop lever angle

N:Pump normal S:Stop the pump.
----------

----------
a=26deg+-5deg b=53deg+-5deg

Timing setting

(1)Pump vertical direction (2)Position of gear mark '2' at No 1 cylinder's beginning of injection (3)B.T.D.C.: aa (4)-
----------
aa=16deg
----------
a=(90deg)