101603-1830 ZEXEL 9 400 610 040 BOSCH INJECTION-PUMP ASSEMBLY 9400610040 1016031830 me056440


101603-1830 INJECTION-PUMP ASSEMBLY
Rating:
77
Buy INJECTION-PUMP ASSEMBLY 101603-1830 zexel genuine, new aftermarket engine parts with delivery

Information injection-pump assembly

BOSCH 9 400 610 040 9400610040
ZEXEL 101603-1830 1016031830
MITSUBISHI ME056440 me056440

Service parts 101603-1830 INJECTION-PUMP ASSEMBLY:

1. _
2. FUEL INJECTION PUMP 101060-4260
3. GOVERNOR 105490-4870
4. SUPPLY PUMP 105210-4151
5. AUTOM. ADVANCE MECHANIS 105614-4100
6. COUPLING PLATE 105662-0590
7. COUPLING PLATE
8. _
9. _
10. NOZZLE AND HOLDER ASSY 105100-6021
11. Nozzle and Holder ME056371
12. Open Pre:MPa(Kqf/cm2) 21.6{220}
13. NOZZLE-HOLDER 105030-5010
14. NOZZLE 105015-5390
15. NOZZLE SET

Include in #1:

101603-1830 as INJECTION-PUMP ASSEMBLY

Cross reference number

BOSCH 9 400 610 040 9400610040
ZEXEL 101603-1830 1016031830
MITSUBISHI ME056440 me056440


Zexel num
Bosch num
Firm num
Name
101603-1830 
9 400 610 040 
ME056440  MITSUBISHI
INJECTION-PUMP ASSEMBLY
6D22 K 14BF INJECTION PUMP ASSY PE6AD PE

Calibration Data:

Adjustment conditions
Test oil
1404 Test oil
  ISO4113 or {SAEJ967d}
Test oil temperature degC   40 40 45
Nozzle and nozzle holder   105780-8140
Bosch type code   EF8511/9A
Nozzle   105780-0000
Bosch type code   DN12SD12T
Nozzle holder   105780-2080
Bosch type code   EF8511/9
Opening pressure MPa   17.2
Opening pressure kgf/cm2   175
Injection pipe
Outer diameter - inner diameter - length (mm)
mm   6-2-600
Overflow valve   131424-5120
Overflow valve opening pressure kPa   255 221 289
Overflow valve opening pressure kgf/cm2   2.6 2.25 2.95
Tester oil delivery pressure kPa   157 157 157
Tester oil delivery pressure kgf/cm2   1.6 1.6 1.6
Direction of rotation (viewed from drive side)
Right
  R
Injection timing adjustment
Direction of rotation (viewed from drive side)
Right
  R
Injection order   1-5-3-6- 2-4
Pre-stroke mm   4.5 4.45 4.55
Beginning of injection position
Governor side
  NO.1
Difference between angles 1
Cal 1-5
deg.   60 59.5 60.5
Difference between angles 2
Cal 1-3
deg.   120 119.5 120.5
Difference between angles 3
Cal 1-6
deg.   180 179.5 180.5
Difference between angles 4
Cyl.1-2
deg.   240 239.5 240.5
Difference between angles 5
Cal 1-4
deg.   300 299.5 300.5
Injection quantity adjustment
Adjusting point   -
Rack position   9.6
Pump speed r/min   700 700 700
Each cylinder's injection qty mm3/st.   112 108.6 115.4
Basic   *
Fixing the rack   *
Standard for adjustment of the maximum variation between cylinders   *
Injection quantity adjustment_02
Adjusting point   C
Rack position   8+-0.5
Pump speed r/min   225 225 225
Each cylinder's injection qty mm3/st.   18.5 15.7 21.3
Fixing the rack   *
Standard for adjustment of the maximum variation between cylinders   *
Injection quantity adjustment_03
Adjusting point   A
Rack position   R1(9.6)
Pump speed r/min   700 700 700
Average injection quantity mm3/st.   112 111 113
Fixing the lever   *
Injection quantity adjustment_04
Adjusting point   B
Rack position   R1(9.6)
Pump speed r/min   1100 1100 1100
Average injection quantity mm3/st.   113.5 111 116
Difference in delivery mm3/st.   9 9 9
Fixing the lever   *
Injection quantity adjustment_05
Adjusting point   E
Rack position   -
Pump speed r/min   100 100 100
Average injection quantity mm3/st.   140 120 160
Fixing the lever   *
Remarks
After startup boost setting
 
Timer adjustment
Pump speed r/min   850--
Advance angle deg.   0 0 0
Remarks
Start
 
Timer adjustment_02
Pump speed r/min   800
Advance angle deg.   0.5
Timer adjustment_03
Pump speed r/min   1000
Advance angle deg.   0.9 0.4 1.4
Timer adjustment_04
Pump speed r/min   1150
Advance angle deg.   3 2.5 3.5
Timer adjustment_05
Pump speed r/min   -
Advance angle deg.   4 4 5
Remarks
Measure the actual speed, stop
 

Test data Ex:

Governor adjustment

Test data 101603-1830
N:Pump speed R:Rack position (mm) (1)Target shim dimension: TH (2)Beginning of damper spring operation: DL (3)Excess fuel setting for starting: SXL
----------
TH=2.3mm DL=6.8-0.2mm SXL=R1(9.6)+0.2mm
----------

Speed control lever angle

Test data 101603-1830
F:Full speed
----------

----------
a=10deg+-5deg

0000000901

Test data 101603-1830
F:Full load I:Idle (1)Stopper bolt setting
----------

----------
a=21.5deg+-5deg b=29deg+-3deg

Stop lever angle

Test data 101603-1830
N:Pump normal S:Stop the pump. (1)Free (at delivery) (2)Rack position = aa (3)Rack position = bb, set the stopper bolt.
----------
aa=13.5mm bb=6-0.5mm
----------
a=(58deg) b=36deg+5deg-7deg c=24deg+-5deg

0000001501 MICRO SWITCH

Adjustment of the micro-switch Adjust the bolt to obtain the following lever position when the micro-switch is ON. (1)Speed N1 (2)Rack position Ra
----------
N1=325+-5r/min Ra=7.3mm
----------

Timing setting

Test data 101603-1830
(1)Pump vertical direction (2)Position of key groove at No 1 cylinder's beginning of injection (3)- (4)-
----------

----------
a=(7deg)




Have questions with 101603-1830?





Group cross 101603-1830 ZEXEL

Mitsubishi 

 
 
INJECTION-PUMP ASSEMBLY
6D14T
 
ME035602 
INJECTION-PUMP ASSEMBLY
6D14T
 
 
INJECTION-PUMP ASSEMBLY
6D15
 
ME035697 
INJECTION-PUMP ASSEMBLY
6D15
 
ME035694 
INJECTION-PUMP ASSEMBLY
6D14
101603-1830  
9 400 610 040 
ME056440 
INJECTION-PUMP ASSEMBLY
6D22

M.Bishi-Hi.-Nag 

9 400 615 023 
EZ40095 
INJECTION-PUMP ASSEMBLY
6AAC
 
EZ40096 
INJECTION-PUMP ASSEMBLY
6AAC

Mitsubishi 

9 400 615 024 
ME056439 
INJECTION-PUMP ASSEMBLY
6D22
 
ME056430 
INJECTION-PUMP ASSEMBLY
6D22
9 400 615 025 
ME037695 
INJECTION-PUMP ASSEMBLY
6D14T
9 400 615 026 
ME037680 
INJECTION-PUMP ASSEMBLY
6D14T
Back to top