101603-1470 ZEXEL F 019 Z20 464 BOSCH INJECTION-PUMP ASSEMBLY f019z20464 1016031470 me035835

Information Cross number Calibration Data Calibration Data Ex

Price: query
Buy now
Add to cart Go to cart

Rating:

Buy INJECTION-PUMP ASSEMBLY 101603-1470 zexel genuine, new aftermarket engine parts with delivery

Information injection-pump assembly

BOSCH F 019 Z20 464 f019z20464

ZEXEL 101603-1470 1016031470

MITSUBISHI ME035835 me035835

Service parts 101603-1470 INJECTION-PUMP ASSEMBLY:

1. _

2. FUEL INJECTION PUMP 101060-9540

3. GOVERNOR 105490-4750

4. SUPPLY PUMP 105210-4641

5. AUTOM. ADVANCE MECHANIS 105624-5100

6. COUPLING PLATE

7. COUPLING PLATE

8. _

9. _

10. NOZZLE AND HOLDER ASSY 105101-4630

11. Nozzle and Holder

12. Open Pre:MPa(Kqf/cm2) 22.1(225)

13. NOZZLE-HOLDER

14. NOZZLE

105015-4220

15. NOZZLE SET

Include in #1:

101603-1470 as INJECTION-PUMP ASSEMBLY

101603-7801 as _

Cross reference number

BOSCH F 019 Z20 464 f019z20464

ZEXEL 101603-1470 1016031470

MITSUBISHI ME035835 me035835

Zexel num

Bosch num

Firm num

Name

101603-1470

F 019 Z20 464

ME035835 MITSUBISHI

INJECTION-PUMP ASSEMBLY
6D14 * K 14BE PE6A PE

Calibration Data:

Adjustment conditions

Test oil
1404 Test oil ISO4113 or {SAEJ967d}

Test oil temperature degC 40 40 45

Nozzle and nozzle holder 105780-8140

Bosch type code EF8511/9A

Nozzle 105780-0000

Bosch type code DN12SD12T

Nozzle holder 105780-2080

Bosch type code EF8511/9

Opening pressure MPa 17.2

Opening pressure kgf/cm2 175

Injection pipe
Outer diameter - inner diameter - length (mm) mm 6-2-600

Overflow valve opening pressure kPa 255 221 289

Overflow valve opening pressure kgf/cm2 2.6 2.25 2.95

Tester oil delivery pressure kPa 157 157 157

Tester oil delivery pressure kgf/cm2 1.6 1.6 1.6

Direction of rotation (viewed from drive side)
Left L

Injection timing adjustment

Direction of rotation (viewed from drive side)
Left L

Injection order 1-5-3-6- 2-4

Pre-stroke mm 3.3 3.25 3.35

Beginning of injection position
Governor side NO.1

Difference between angles 1
Cal 1-5 deg. 60 59.5 60.5

Difference between angles 2
Cal 1-3 deg. 120 119.5 120.5

Difference between angles 3
Cal 1-6 deg. 180 179.5 180.5

Difference between angles 4
Cyl.1-2 deg. 240 239.5 240.5

Difference between angles 5
Cal 1-4 deg. 300 299.5 300.5

Injection quantity adjustment

Adjusting point -

Rack position 11.5

Pump speed r/min 850 850 850

Each cylinder's injection qty mm3/st. 61.5 59.7 63.3

Basic *

Fixing the rack *

Standard for adjustment of the maximum variation between cylinders *

Injection quantity adjustment_02

Adjusting point C

Rack position 9.7+-0.5

Pump speed r/min 275 275 275

Each cylinder's injection qty mm3/st. 10.5 9 12

Fixing the rack *

Standard for adjustment of the maximum variation between cylinders *

Injection quantity adjustment_03

Adjusting point A

Rack position R1(11.5)

Pump speed r/min 850 850 850

Average injection quantity mm3/st. 61.5 60.5 62.5

Fixing the lever *

Injection quantity adjustment_04

Adjusting point B

Rack position R1(11.5)

Pump speed r/min 1500 1500 1500

Average injection quantity mm3/st. 65.8 63.1 68.5

Difference in delivery mm3/st. 5.4 5.4 5.4

Fixing the lever *

Timer adjustment

Pump speed r/min 850+-50

Advance angle deg. 0 0 0

Remarks
Start

Timer adjustment_02

Pump speed r/min 1200

Advance angle deg. 2.6 2.1 3.1

Timer adjustment_03

Pump speed r/min 1500

Advance angle deg. 5.5 5 6

Remarks
Finish

Test data Ex:

Governor adjustment

N:Pump speed R:Rack position (mm) (1)Beginning of damper spring operation: DL (2)Excess fuel setting for starting: SXL
----------
DL=6.5-0.2mm SXL=R1(11.5)+1+0.8mm
----------

0000000901

F:Full load I:Idle (1)Stopper bolt setting
----------

----------
a=17deg+-5deg b=27.5deg+-3deg

Stop lever angle

N:Pump normal S:Stop the pump.
----------

----------
a=60deg+-5deg b=71deg+-5deg

0000001501 MICRO SWITCH

Adjustment of the micro-switch Adjust the bolt to obtain the following lever position when the micro-switch is ON. (1)Speed N1 (2)Rack position Ra
----------
N1=410r/min Ra=9.1mm
----------

Timing setting

(1)Pump vertical direction (2)Position of timer's tooth at No 1 cylinder's beginning of injection (3)B.T.D.C.: aa (4)-
----------
aa=16deg
----------
a=(2deg)