101602-3350 ZEXEL INJECTION-PUMP ASSEMBLY Calibration Data 1016023350 6137711510

Information Cross number Calibration Data Calibration Data Ex

Price: query
Buy now
Add to cart Go to cart

Rating:

Buy INJECTION-PUMP ASSEMBLY 101602-3350 zexel genuine, new aftermarket engine parts with delivery

Information injection-pump assembly

ZEXEL 101602-3350 1016023350

KOMATSU 6137711510 6137711510

Cross reference number

ZEXEL 101602-3350 1016023350

KOMATSU 6137711510 6137711510

Zexel num

Bosch num

Firm num

Name

101602-3350

6137711510 KOMATSU

INJECTION-PUMP ASSEMBLY
SL6D105 * K

Calibration Data:

Adjustment conditions

Test oil
1404 Test oil ISO4113 or {SAEJ967d}

Test oil temperature degC 40 40 45

Nozzle and nozzle holder 105780-8140

Bosch type code EF8511/9A

Nozzle 105780-0000

Bosch type code DN12SD12T

Nozzle holder 105780-2080

Bosch type code EF8511/9

Opening pressure MPa 17.2

Opening pressure kgf/cm2 175

Injection pipe
Outer diameter - inner diameter - length (mm) mm 6-2-600

Tester oil delivery pressure kPa 157 157 157

Tester oil delivery pressure kgf/cm2 1.6 1.6 1.6

Direction of rotation (viewed from drive side)
Right R

Injection timing adjustment

Direction of rotation (viewed from drive side)
Right R

Injection order 1-5-3-6- 2-4

Pre-stroke mm 3.5 3.45 3.55

Beginning of injection position
Drive side NO.1

Difference between angles 1
Cal 1-5 deg. 60 59.5 60.5

Difference between angles 2
Cal 1-3 deg. 120 119.5 120.5

Difference between angles 3
Cal 1-6 deg. 180 179.5 180.5

Difference between angles 4
Cyl.1-2 deg. 240 239.5 240.5

Difference between angles 5
Cal 1-4 deg. 300 299.5 300.5

Injection quantity adjustment

Adjusting point A

Rack position 9.4

Pump speed r/min 900 900 900

Average injection quantity mm3/st. 51.5 50.5 52.5

Max. variation between cylinders % 0 -2 2

Basic *

Fixing the lever *

Injection quantity adjustment_02

Adjusting point B

Rack position 8+-0.5

Pump speed r/min 325 325 325

Average injection quantity mm3/st. 10.5 9 12

Max. variation between cylinders % 0 -10 10

Fixing the rack *

Test data Ex:

Governor adjustment

N:Pump speed R:Rack position (mm) (1)Target notch: K (2)Tolerance for racks not indicated: +-0.05mm. (3)Rack difference from N = N1 (4)Rack difference between N = N2 and N = N3
----------
K=15 N1=900r/min N2=900r/min N3=450r/min
----------

Speed control lever angle

F:Full speed I:Idle S:Stop
----------

----------
a=6deg+-5deg b=30deg+-5deg c=32deg+-3deg

0000001501 LEVER

(F) P/N: Part number of the shim L1:Thickness (mm) 1. Adjustment of the control lever (1)Perform idling with the control lever (A) contacting the pushrod (B). At this time, confirm that the spring (C) is not compressed by control lever (A)'s operating torque. (2)To set the stop position, compress spring (C) using the control lever (A) and adjust the rack so that it contacts the guide screw (D) at position L2. Then, set and fix using the lock nut (E). Adjust the rack position L2 at this time using the shim (F). (3)Confirm that the control lever (A) returns to the idling position when pulled in the stop direction and then released.
----------
L2=0.2~2mm
----------