101602-3130 ZEXEL 9 400 614 811 BOSCH INJECTION-PUMP ASSEMBLY 9400614811 1016023130 6136711310

Information Cross number Calibration Data Calibration Data Ex

Price: query
Buy now
Add to cart Go to cart

Rating:

Buy INJECTION-PUMP ASSEMBLY 101602-3130 zexel genuine, new aftermarket engine parts with delivery

Information injection-pump assembly

BOSCH 9 400 614 811 9400614811

ZEXEL 101602-3130 1016023130

KOMATSU 6136711310 6136711310

Service parts 101602-3130 INJECTION-PUMP ASSEMBLY:

1. _

2. FUEL INJECTION PUMP 101060-0810

3. GOVERNOR 105410-4690

4. SUPPLY PUMP 105210-4231

5. AUTOM. ADVANCE MECHANIS

6. COUPLING PLATE 105661-0330

7. COUPLING PLATE

8. _

9. _

10. NOZZLE AND HOLDER ASSY 105100-5430

11. Nozzle and Holder 6137-12-3100

12. Open Pre:MPa(Kqf/cm2) 22.1{225}

13. NOZZLE-HOLDER 105031-4480

14. NOZZLE

105015-5020

15. NOZZLE SET

Include in #1:

101432-4011 as _

101602-3130 as INJECTION-PUMP ASSEMBLY

Cross reference number

BOSCH 9 400 614 811 9400614811

ZEXEL 101602-3130 1016023130

KOMATSU 6136711310 6136711310

Zexel num

Bosch num

Firm num

Name

101602-3130

9 400 614 811

6136711310 KOMATSU

INJECTION-PUMP ASSEMBLY
6D105 K 14BE INJECTION PUMP ASSY PE6A PE

Calibration Data:

Adjustment conditions

Test oil
1404 Test oil ISO4113 or {SAEJ967d}

Test oil temperature degC 40 40 45

Nozzle and nozzle holder 105780-8140

Bosch type code EF8511/9A

Nozzle 105780-0000

Bosch type code DN12SD12T

Nozzle holder 105780-2080

Bosch type code EF8511/9

Opening pressure MPa 17.2

Opening pressure kgf/cm2 175

Injection pipe
Outer diameter - inner diameter - length (mm) mm 6-2-600

Tester oil delivery pressure kPa 157 157 157

Tester oil delivery pressure kgf/cm2 1.6 1.6 1.6

Direction of rotation (viewed from drive side)
Right R

Injection timing adjustment

Direction of rotation (viewed from drive side)
Right R

Injection order 1-5-3-6- 2-4

Pre-stroke mm 3.5 3.45 3.55

Beginning of injection position
Drive side NO.1

Difference between angles 1
Cal 1-5 deg. 60 59.5 60.5

Difference between angles 2
Cal 1-3 deg. 120 119.5 120.5

Difference between angles 3
Cal 1-6 deg. 180 179.5 180.5

Difference between angles 4
Cyl.1-2 deg. 240 239.5 240.5

Difference between angles 5
Cal 1-4 deg. 300 299.5 300.5

Injection quantity adjustment

Adjusting point A

Rack position 7.8

Pump speed r/min 1175 1175 1175

Average injection quantity mm3/st. 39.7 38.7 40.7

Max. variation between cylinders % 0 -2 2

Basic *

Fixing the lever *

Injection quantity adjustment_02

Adjusting point C

Rack position 6.3+-0.5

Pump speed r/min 400 400 400

Average injection quantity mm3/st. 8.3 6.5 10.1

Max. variation between cylinders % 0 -10 10

Fixing the rack *

Test data Ex:

Governor adjustment

N:Pump speed R:Rack position (mm) (1)Target notch: K (2)Main spring setting
----------
K=7
----------

Speed control lever angle

F:Full speed I:Idle S:Stop
----------

----------
a=11deg+-5deg b=30deg+-5deg c=32deg+-3deg

0000001501 LEVER

(F) P/N: Part number of the shim L1:Thickness (mm) 1. Adjustment of the control lever (1)Perform idling with the control lever (A) contacting the pushrod (B). At this time, confirm that the spring (C) is not compressed by control lever (A)'s operating torque. (2)To set the stop position, compress spring (C) using the control lever (A) and adjust the rack so that it contacts the guide screw (D) at position L2. Then, set and fix using the lock nut (E). Adjust the rack position L2 at this time using the shim (F). (3)Confirm that the control lever (A) returns to the idling position when pulled in the stop direction and then released.
----------
L2=0.2~2mm
----------