101601-5772 ZEXEL F 01G 09U 02Y BOSCH INJECTION-PUMP ASSEMBLY f01g09u02y 1016015772 220007141a


101601-5772 INJECTION-PUMP ASSEMBLY
Rating:
8
Buy INJECTION-PUMP ASSEMBLY 101601-5772 zexel genuine, new aftermarket engine parts with delivery

Information injection-pump assembly

BOSCH F 01G 09U 02Y f01g09u02y
ZEXEL 101601-5772 1016015772
HINO 220007141A 220007141a

Service parts 101601-5772 INJECTION-PUMP ASSEMBLY:

1. _
2. FUEL INJECTION PUMP 101060-5210
3. GOVERNOR 105921-4761
4. SUPPLY PUMP 105210-5240
5. AUTOM. ADVANCE MECHANIS 105672-0220
6. COUPLING PLATE 105662-1160
7. COUPLING PLATE
8. _
9. _
10. NOZZLE AND HOLDER ASSY 105101-6280
11. Nozzle and Holder 23600-2133
12. Open Pre:MPa(Kqf/cm2) 19.6{200}
13. NOZZLE-HOLDER 105030-4300
14. NOZZLE 105015-8590
15. NOZZLE SET

Include in #1:

101601-5772 as INJECTION-PUMP ASSEMBLY

Cross reference number

BOSCH F 01G 09U 02Y f01g09u02y
ZEXEL 101601-5772 1016015772
HINO 220007141A 220007141a


Zexel num
Bosch num
Firm num
Name
101601-5772 
101601-5773 
F 01G 09U 02Y 
220007141A  HINO
INJECTION-PUMP ASSEMBLY
H07D * K

Calibration Data:

Adjustment conditions
Test oil
1404 Test oil
  ISO4113 or {SAEJ967d}
Test oil temperature degC   40 40 45
Nozzle and nozzle holder   105780-8140
Bosch type code   EF8511/9A
Nozzle   105780-0000
Bosch type code   DN12SD12T
Nozzle holder   105780-2080
Bosch type code   EF8511/9
Opening pressure MPa   17.2
Opening pressure kgf/cm2   175
Injection pipe
Outer diameter - inner diameter - length (mm)
mm   6-2-600
Overflow valve   131424-8320
Overflow valve opening pressure kPa   108 88 128
Overflow valve opening pressure kgf/cm2   1.1 0.9 1.3
Tester oil delivery pressure kPa   157 157 157
Tester oil delivery pressure kgf/cm2   1.6 1.6 1.6
Direction of rotation (viewed from drive side)
Right
  R
Injection timing adjustment
Direction of rotation (viewed from drive side)
Right
  R
Injection order   1-4-2-6- 3-5
Pre-stroke mm   3.8 3.77 3.83
Beginning of injection position
Drive side
  NO.1
Difference between angles 1
Cal 1-4
deg.   60 59.75 60.25
Difference between angles 2
Cyl.1-2
deg.   120 119.75 120.25
Difference between angles 3
Cal 1-6
deg.   180 179.75 180.25
Difference between angles 4
Cal 1-3
deg.   240 239.75 240.25
Difference between angles 5
Cal 1-5
deg.   300 299.75 300.25
Injection quantity adjustment
Adjusting point   -
Rack position   11.1
Pump speed r/min   850 850 850
Average injection quantity mm3/st.   70.5 68.9 72.1
Max. variation between cylinders %   0 -3.5 3.5
Basic   *
Fixing the rack   *
Standard for adjustment of the maximum variation between cylinders   *
Injection quantity adjustment_02
Adjusting point   H
Rack position   9+-0.5
Pump speed r/min   250 250 250
Each cylinder's injection qty mm3/st.   15 14 16
Fixing the rack   *
Standard for adjustment of the maximum variation between cylinders   *
Injection quantity adjustment_03
Adjusting point   A
Rack position   R1(11.1)
Pump speed r/min   850 850 850
Average injection quantity mm3/st.   70.5 69.5 71.5
Basic   *
Fixing the lever   *
Injection quantity adjustment_04
Adjusting point   B
Rack position   R1+0.5
Pump speed r/min   1450 1450 1450
Average injection quantity mm3/st.   82.1 78.1 86.1
Fixing the lever   *
Injection quantity adjustment_05
Adjusting point   C
Rack position   R1-0.3
Pump speed r/min   600 600 600
Average injection quantity mm3/st.   54.8 50.8 58.8
Fixing the lever   *
Injection quantity adjustment_06
Adjusting point   D
Rack position   R1+0.5
Pump speed r/min   1150 1150 1150
Average injection quantity mm3/st.   80.3 76.3 84.3
Fixing the lever   *
Injection quantity adjustment_07
Adjusting point   I
Rack position   -
Pump speed r/min   100 100 100
Average injection quantity mm3/st.   140 140 150
Fixing the lever   *
Rack limit   *
Timer adjustment
Pump speed r/min   900--
Advance angle deg.   0 0 0
Remarks
Start
 
Timer adjustment_02
Pump speed r/min   850
Advance angle deg.   0.3
Timer adjustment_03
Pump speed r/min   1450
Advance angle deg.   4.5 4.2 4.8
Remarks
Finish
 

Test data Ex:

Governor adjustment

Test data 101601-5772
N:Pump speed R:Rack position (mm) (1)Torque cam stamping: T1 (2)Tolerance for racks not indicated: +-0.05mm. (3)RACK LIMIT
----------
T1=F03
----------

Speed control lever angle

Test data 101601-5772
F:Full speed I:Idle (1)Use the pin at R = aa (2)Stopper bolt set position 'H'
----------
aa=57mm
----------
a=40deg+-3deg b=44deg+-5deg

Stop lever angle

Test data 101601-5772
N:Pump normal S:Stop the pump. (1)Use the hole at R = aa
----------
aa=35mm
----------
a=14.5deg+-5deg b=40deg+-5deg

0000001501 TAMPER PROOF

Test data 101601-5772
1. Method for setting tamperproof proofing (1)After governor adjustment (torque cam phase adjustment), move the load lever to increase the full rack position to Ra. (2)At pump speed N1, push in the screw (A) until the rack position is Rb. (3)Temporarily caulk using the tip of a screwdriver (4)Confirm that the rack at that time is at Rc. (5)Lock using setscrew (B). (Tightening torque = T) (6)Next, coat (C) with adhesive and then pressfit. (7)Then, readjust the full rack position using the load lever.
----------
N1=1450r/min Ra=R1(11.1)+1mm Rb=R1(11.1)+1mm Rc=R1(11.1)+1mm
----------
T=3.4~4.9N-m(0.35~0.5Kgf-m)

Timing setting

Test data 101601-5772
(1)Pump vertical direction (2)Coupling's key groove position at No 1 cylinder's beginning of injection (3)- (4)-
----------

----------
a=(50deg)




Have questions with 101601-5772?





Group cross 101601-5772 ZEXEL

Hino 

F 019 Z10 345 
220006740A 
INJECTION-PUMP ASSEMBLY
H07D-A
F 019 Z10 346 
220006741A 
INJECTION-PUMP ASSEMBLY
H07D-A
F 019 Z10 347 
220006742A 
INJECTION-PUMP ASSEMBLY
H07D-A
F 019 Z10 348 
220006742B 
INJECTION-PUMP ASSEMBLY
H07D-A
F 019 Z10 349 
220006743A 
INJECTION-PUMP ASSEMBLY
H07D-A
F 019 Z10 350 
220006744A 
INJECTION-PUMP ASSEMBLY
H07D-A
9 400 614 624 
220006745A 
INJECTION-PUMP ASSEMBLY
H07D-A
 
220006800A 
INJECTION-PUMP ASSEMBLY
H07D-A
 
220006801A 
INJECTION-PUMP ASSEMBLY
H07D-A
 
220006801B 
INJECTION-PUMP ASSEMBLY
H07D-A
 
220006802A 
INJECTION-PUMP ASSEMBLY
H07D-A
F 019 Z10 492 
220006803A 
INJECTION-PUMP ASSEMBLY
H07D-A
 
220006980A 
INJECTION-PUMP ASSEMBLY
H07D-A
 
220006981A 
INJECTION-PUMP ASSEMBLY
H07D-A
 
220006981B 
INJECTION-PUMP ASSEMBLY
H07D-A
 
220006982A 
INJECTION-PUMP ASSEMBLY
H07D-A
F 019 Z10 493 
220006983A 
INJECTION-PUMP ASSEMBLY
H07D-A
 
220006880A 
INJECTION-PUMP ASSEMBLY
H07D-A
 
220006881A 
INJECTION-PUMP ASSEMBLY
H07D-A
 
220006881B 
INJECTION-PUMP ASSEMBLY
H07D-A
 
220006881A 
INJECTION-PUMP ASSEMBLY
H07D-A
 
220006882A 
INJECTION-PUMP ASSEMBLY
H07D-A
 
220006882B 
INJECTION-PUMP ASSEMBLY
H07D-A
 
220006883A 
INJECTION-PUMP ASSEMBLY
H07D-A
F 019 Z10 168 
220006884A 
INJECTION-PUMP ASSEMBLY
H07D-A
 
220007000A 
INJECTION-PUMP ASSEMBLY
H07D
 
220007000B 
INJECTION-PUMP ASSEMBLY
H07D-A
 
220007001A 
INJECTION-PUMP ASSEMBLY
H07D-A
9 400 614 625 
220007002A 
INJECTION-PUMP ASSEMBLY
H07D-A
 
220007170A 
INJECTION-PUMP ASSEMBLY
H07D-A
 
220007170B 
INJECTION-PUMP ASSEMBLY
H07D-A
 
220007171A 
INJECTION-PUMP ASSEMBLY
H07D-A
 
220007171B 
INJECTION-PUMP ASSEMBLY
H07D-A
 
220007172A 
INJECTION-PUMP ASSEMBLY
H07D-A
F 019 Z10 169 
220007173A 
INJECTION-PUMP ASSEMBLY
H07D-A
F 019 Z10 818 
220007150A 
INJECTION-PUMP ASSEMBLY
W06E
F 01G 09U 02X 
 
INJECTION-PUMP ASSEMBLY

Hino 

9 400 614 626 
220007151A 
INJECTION-PUMP ASSEMBLY
W06E
 
220007140A 
INJECTION-PUMP ASSEMBLY
H07D
F 019 Z10 494 
220007140B 
INJECTION-PUMP ASSEMBLY
H07D
101601-5772  

101601-5773 
F 01G 09U 02Y 
220007141A 
INJECTION-PUMP ASSEMBLY
H07D
9 400 614 627 
220007141B 
INJECTION-PUMP ASSEMBLY
H07D
F 019 Z10 819 
220007290A 
INJECTION-PUMP ASSEMBLY
W06E
F 019 Z10 819 
S220007290A 
INJECTION-PUMP ASSEMBLY
W06E
F 01G 09U 02Z 
220007291A 
INJECTION-PUMP ASSEMBLY
W06E
F 01G 09U 030 
 
INJECTION-PUMP ASSEMBLY

Hino 

9 400 614 628 
220007291B 
INJECTION-PUMP ASSEMBLY
W06E
F 019 Z10 820 
220007310A 
INJECTION-PUMP ASSEMBLY
H07D-A
F 019 Z10 821 
220007311A 
INJECTION-PUMP ASSEMBLY
H07D-A
F 019 Z10 495 
220007311B 
INJECTION-PUMP ASSEMBLY
H07D-A
F 019 Z10 496 
220007312A 
INJECTION-PUMP ASSEMBLY
H07D-A
9 400 611 506 
220007313A 
INJECTION-PUMP ASSEMBLY
H07D-A
Back to top