101601-5682 ZEXEL 9 400 611 429 BOSCH INJECTION-PUMP ASSEMBLY 9400611429 1016015682 220006451b


101601-5682 INJECTION-PUMP ASSEMBLY
Rating:
30
Buy INJECTION-PUMP ASSEMBLY 101601-5682 zexel genuine, new aftermarket engine parts with delivery

Information injection-pump assembly

BOSCH 9 400 611 429 9400611429
ZEXEL 101601-5682 1016015682
HINO 220006451B 220006451b

Service parts 101601-5682 INJECTION-PUMP ASSEMBLY:

1. _
2. FUEL INJECTION PUMP 101060-9931
3. GOVERNOR 105921-4041
4. SUPPLY PUMP 105220-5140
5. AUTOM. ADVANCE MECHANIS 105676-0671
6. COUPLING PLATE
7. COUPLING PLATE
8. _
9. _
10. NOZZLE AND HOLDER ASSY 105110-4292
11. Nozzle and Holder 23600-1593A
12. Open Pre:MPa(Kqf/cm2) 21.6{220}
13. NOZZLE-HOLDER 105041-5041
14. NOZZLE 105015-5640
15. NOZZLE SET

Include in #1:

101601-5682 as INJECTION-PUMP ASSEMBLY

Cross reference number

BOSCH 9 400 611 429 9400611429
ZEXEL 101601-5682 1016015682
HINO 220006451B 220006451b


Zexel num
Bosch num
Firm num
Name
101601-5682 
9 400 611 429 
220006451B  HINO
INJECTION-PUMP ASSEMBLY
W06E K 14BE INJECTION PUMP ASSY PE6A PE

Calibration Data:

Adjustment conditions
Test oil
1404 Test oil
  ISO4113 or {SAEJ967d}
Test oil temperature degC   40 40 45
Nozzle and nozzle holder   105780-8140
Bosch type code   EF8511/9A
Nozzle   105780-0000
Bosch type code   DN12SD12T
Nozzle holder   105780-2080
Bosch type code   EF8511/9
Opening pressure MPa   17.2
Opening pressure kgf/cm2   175
Injection pipe
Outer diameter - inner diameter - length (mm)
mm   6-2-600
Overflow valve   131424-5720
Overflow valve opening pressure kPa   255 221 289
Overflow valve opening pressure kgf/cm2   2.6 2.25 2.95
Tester oil delivery pressure kPa   157 157 157
Tester oil delivery pressure kgf/cm2   1.6 1.6 1.6
Direction of rotation (viewed from drive side)
Right
  R
Injection timing adjustment
Direction of rotation (viewed from drive side)
Right
  R
Injection order   1-4-2-6- 3-5
Pre-stroke mm   3.1 3.07 3.13
Beginning of injection position
Drive side
  NO.1
Difference between angles 1
Cal 1-4
deg.   60 59.75 60.25
Difference between angles 2
Cyl.1-2
deg.   120 119.75 120.25
Difference between angles 3
Cal 1-6
deg.   180 179.75 180.25
Difference between angles 4
Cal 1-3
deg.   240 239.75 240.25
Difference between angles 5
Cal 1-5
deg.   300 299.75 300.25
Injection quantity adjustment
Adjusting point   -
Rack position   9.5
Pump speed r/min   900 900 900
Average injection quantity mm3/st.   60.2 58.2 62.2
Max. variation between cylinders %   0 -3.5 3.5
Basic   *
Fixing the rack   *
Standard for adjustment of the maximum variation between cylinders   *
Injection quantity adjustment_02
Adjusting point   H
Rack position   8+-0.5
Pump speed r/min   250 250 250
Average injection quantity mm3/st.   6.8 5.3 8.3
Max. variation between cylinders %   0 -10 10
Fixing the rack   *
Standard for adjustment of the maximum variation between cylinders   *
Injection quantity adjustment_03
Adjusting point   A
Rack position   R1(9.5)
Pump speed r/min   900 900 900
Average injection quantity mm3/st.   60.2 59.2 61.2
Basic   *
Fixing the lever   *
Injection quantity adjustment_04
Adjusting point   B
Rack position   R1+0.1
Pump speed r/min   1500 1500 1500
Average injection quantity mm3/st.   67.3 63.3 71.3
Fixing the lever   *
Injection quantity adjustment_05
Adjusting point   C
Rack position   R1-0.45
Pump speed r/min   600 600 600
Average injection quantity mm3/st.   37.9 33.9 41.9
Fixing the lever   *
Injection quantity adjustment_06
Adjusting point   D
Rack position   R1+0.15
Pump speed r/min   1200 1200 1200
Average injection quantity mm3/st.   67.8 63.8 71.8
Fixing the lever   *
Injection quantity adjustment_07
Adjusting point   E
Rack position   R1(9.5)
Pump speed r/min   400 400 400
Average injection quantity mm3/st.   32.9 28.9 36.9
Fixing the lever   *
Injection quantity adjustment_08
Adjusting point   I
Rack position   -
Pump speed r/min   100 100 100
Average injection quantity mm3/st.   99 99 109
Fixing the lever   *
Rack limit   *
Timer adjustment
Pump speed r/min   1000+50
Advance angle deg.   0 0 0
Remarks
Start
 
Timer adjustment_02
Pump speed r/min   1500
Advance angle deg.   3.5 3.2 3.8
Remarks
Finish
 

Test data Ex:

Governor adjustment

Test data 101601-5682
N:Pump speed R:Rack position (mm) (1)Torque cam stamping: T1 (2)Tolerance for racks not indicated: +-0.05mm. (3)RACK LIMIT
----------
T1=C10
----------

Speed control lever angle

Test data 101601-5682
F:Full speed I:Idle (1)Stopper bolt set position 'H'
----------

----------
a=32deg+-3deg b=34deg+-5deg

Stop lever angle

Test data 101601-5682
N:Pump normal S:Stop the pump. (1)Stopper bolt setting (2)(Apply red paint after setting.) (3)Engine normal
----------

----------
a=40deg+-5deg b=40deg+-5deg c=35deg+-2deg

0000001501 TAMPER PROOF

Test data 101601-5682
1. Method for setting tamperproof proofing (1)After governor adjustment (torque cam phase adjustment), move the load lever to increase the full rack position to Ra. (2)At pump speed N1, push in the screw (A) until the rack position is Rb. (3)Temporarily caulk using the tip of a screwdriver (4)Confirm that the rack at that time is at Rc. (5)Lock using setscrew (B). (Tightening torque = T) (6)Next, coat (C) with adhesive and then pressfit. (7)Then, readjust the full rack position using the load lever.
----------
N1=1500r/min Ra=(0.4)mm Rb=R2(10)mm Rc=R2(10)mm
----------
T=4.9~7N-m(0.5~0.7Kgf-m)

Timing setting

Test data 101601-5682
(1)Pump vertical direction (2)Position of gear's standard threaded hole at No 1 cylinder's beginning of injection (3)- (4)-
----------

----------
a=(70deg)




Have questions with 101601-5682?





Group cross 101601-5682 ZEXEL

Hino 

 
220006410A 
INJECTION-PUMP ASSEMBLY
H07D-A
 
220006420A 
INJECTION-PUMP ASSEMBLY
H07-1
 
220006411A 
INJECTION-PUMP ASSEMBLY
H07D-A
 
220006412A 
INJECTION-PUMP ASSEMBLY
H07D-A
 
220006412B 
INJECTION-PUMP ASSEMBLY
H07D-A
F 019 Z20 455 
220006413A 
INJECTION-PUMP ASSEMBLY
H07D-A
F 019 Z10 490 
220006414A 
INJECTION-PUMP ASSEMBLY
H07D-A
 
220006322A 
INJECTION-PUMP ASSEMBLY
H07D-A
9 400 614 622 
220006323A 
INJECTION-PUMP ASSEMBLY
H07D-A
 
220006311A 
INJECTION-PUMP ASSEMBLY
H07D-A
 
220006341A 
INJECTION-PUMP ASSEMBLY
H07D-A
 
220006342A 
INJECTION-PUMP ASSEMBLY
H07D-A
 
220006342B 
INJECTION-PUMP ASSEMBLY
H07D-A
 
220006342A 
INJECTION-PUMP ASSEMBLY
H07D-A
 
220006343A 
INJECTION-PUMP ASSEMBLY
H07D-A
 
220006343B 
INJECTION-PUMP ASSEMBLY
H07D-A
F 019 Z20 456 
220006344A 
INJECTION-PUMP ASSEMBLY
H07D-A
F 019 Z10 167 
220006345A 
INJECTION-PUMP ASSEMBLY
H07D-A
 
220006430A 
INJECTION-PUMP ASSEMBLY
H07D-A
 
220006431A 
INJECTION-PUMP ASSEMBLY
H07D-A
 
220006431B 
INJECTION-PUMP ASSEMBLY
H07D-A
F 019 Z20 457 
220006432A 
INJECTION-PUMP ASSEMBLY
H07D-A
F 019 Z10 491 
220006433A 
INJECTION-PUMP ASSEMBLY
H07D-A
9 400 614 623 
220006440A 
INJECTION-PUMP ASSEMBLY
H07D-A
 
220006441A 
INJECTION-PUMP ASSEMBLY
H07D-A
 
220006450A 
INJECTION-PUMP ASSEMBLY
W06E
 
 
INJECTION-PUMP ASSEMBLY

Hino 

 
220006451A 
INJECTION-PUMP ASSEMBLY
101601-5682  
9 400 611 429 
220006451B 
INJECTION-PUMP ASSEMBLY
W06E
F 019 Z10 339 
220006540A 
INJECTION-PUMP ASSEMBLY
H07D-A
F 019 Z10 340 
220006541A 
INJECTION-PUMP ASSEMBLY
H07D-A
F 019 Z10 341 
220006542A 
INJECTION-PUMP ASSEMBLY
H07D-A
F 019 Z10 342 
220006542B 
INJECTION-PUMP ASSEMBLY
H07D-A
F 019 Z10 343 
220006543A 
INJECTION-PUMP ASSEMBLY
H07D-A
F 019 Z10 344 
220006544A 
INJECTION-PUMP ASSEMBLY
H07D-A
F 01G 09U 02W 
220006545A 
INJECTION-PUMP ASSEMBLY
H07D-A
Back to top