101601-5658 ZEXEL F 019 Z10 167 BOSCH INJECTION-PUMP ASSEMBLY f019z10167 1016015658 220006345a


 

Information injection-pump assembly

BOSCH F 019 Z10 167 f019z10167
ZEXEL 101601-5658 1016015658
HINO 220006345A 220006345a
101601-5658 INJECTION-PUMP ASSEMBLY
Rating:
16
Buy INJECTION-PUMP ASSEMBLY 101601-5658 zexel genuine, new aftermarket engine parts with delivery

Service parts 101601-5658 INJECTION-PUMP ASSEMBLY:

1. _
2. FUEL INJECTION PUMP 101060-5211
3. GOVERNOR 105921-4166
4. SUPPLY PUMP 105210-5240
5. AUTOM. ADVANCE MECHANIS 105672-0120
6. COUPLING PLATE 105662-1160
7. COUPLING PLATE
8. _
9. _
10. NOZZLE AND HOLDER ASSY 105101-6280
11. Nozzle and Holder
12. Open Pre:MPa(Kqf/cm2) 19.6{200}
13. NOZZLE-HOLDER 105030-4300
14. NOZZLE 105015-8590
15. NOZZLE SET

Include in #1:

101601-5658 as INJECTION-PUMP ASSEMBLY

Cross reference number

Zexel num
Bosch num
Firm num
Name
101601-5658 
F 019 Z10 167 
220006345A  HINO
INJECTION-PUMP ASSEMBLY
H07D-A * K




Information:

For additional torque specifications, not included in this section, refer to Torque Specifications, SENR3130, in the Service Manual or available from your Caterpillar dealer. Use the standard torque values for all fasteners unless otherwise specified in this publication or in the Service Manual.
Be very careful never to mix metric with U.S. customary (standard) fasteners. Mismatched or incorrect fasteners will cause engine damage or malfunction and may even result in personal injury.Original fasteners removed from the engine should be saved for reassembly whenever possible. If new fasteners are needed, they must be of the same size and grade as the ones that are being replaced.The material strength identification is usually shown on the bolt head by numbers (8.8, 10.9, etc.). The following chart gives general torques for bolts and nuts with Metric Threads of SAE Grade 8.8 or better quality.
Metric hardware must be replaced with metric hardware. Check parts manual for proper replacement.Torque for Standard Hose Clamps-Worm Drive Band Type
The following chart gives the torques for initial installation of hose clamps on new hose and for reassembly or tightening of hose clamps on existing hose.
Torque for Constant Torque Hose Clamps
A constant torque hose clamp can be used in place of any standard hose clamp. Make sure the constant torque hose clamp is the same size as the standard clamp. Due to extreme temperature changes, the hose will heat set. Heat setting causes hose clamps to loosen. Loose hose clamps can result in leaks. There have been reports of component failures caused by hose clamps loosening. The new, constant torque hose clamp will help prevent these failures.Each installation/application can be different depending on the type of hose, fitting material and anticipated expansion or contraction of the hose and fittings. A torque wrench should be used for proper installation of the new, constant torque hose clamps. Constant torque hose clamps should be installed as follows:* To allow for maximum expansion, install clamps at 5.7 N m (50 lb in).* To allow for equal expansion and contraction, install clamps at 10.2 N m (90 lb in).* To allow for maximum contraction, install clamps at 14.1 N m (125 lb in).

Have questions with 101601-5658?





Group cross 101601-5658 ZEXEL

Hino 

 
220006341A 
INJECTION-PUMP ASSEMBLY
H07D-A
 
220006342A 
INJECTION-PUMP ASSEMBLY
H07D-A
 
220006342B 
INJECTION-PUMP ASSEMBLY
H07D-A
 
220006342A 
INJECTION-PUMP ASSEMBLY
H07D-A
 
220006343A 
INJECTION-PUMP ASSEMBLY
H07D-A
 
220006343B 
INJECTION-PUMP ASSEMBLY
H07D-A
F 019 Z20 456 
220006344A 
INJECTION-PUMP ASSEMBLY
H07D-A
101601-5658  
F 019 Z10 167 
220006345A 
INJECTION-PUMP ASSEMBLY
H07D-A
Back to top