101501-2040 ZEXEL INJECTION-PUMP ASSEMBLY Calibration Data 1015012040 220009230a


101501-2040 INJECTION-PUMP ASSEMBLY
Rating:
76
Buy INJECTION-PUMP ASSEMBLY 101501-2040 zexel genuine, new aftermarket engine parts with delivery

Information injection-pump assembly

ZEXEL 101501-2040 1015012040
HINO 220009230A 220009230a

Service parts 101501-2040 INJECTION-PUMP ASSEMBLY:

1. _
2. FUEL INJECTION PUMP 101050-0070
3. GOVERNOR 105932-1870
4. SUPPLY PUMP 105210-6060
5. AUTOM. ADVANCE MECHANIS 105672-5270
6. COUPLING PLATE 105662-1520
7. COUPLING PLATE
8. _
9. _
10. NOZZLE AND HOLDER ASSY 105101-7705
11. Nozzle and Holder 23600-2663C
12. Open Pre:MPa(Kqf/cm2) 16.7{170}/21.6{220}
13. NOZZLE-HOLDER 105030-3601
14. NOZZLE
15. NOZZLE SET 105019-0314

Include in #1:

101501-2040 as INJECTION-PUMP ASSEMBLY

Include in #2:

Cross reference number

ZEXEL 101501-2040 1015012040
HINO 220009230A 220009230a


Zexel num
Bosch num
Firm num
Name
101501-2040 
101501-2041 
 
220009230A  HINO
INJECTION-PUMP ASSEMBLY
J07C * K

Calibration Data:

Adjustment conditions
Test oil
1404 Test oil
  ISO4113 or {SAEJ967d}
Test oil temperature degC   40 40 45
Nozzle and nozzle holder   105780-8250
Bosch type code   1 688 901 101
Nozzle   105780-0120
Bosch type code   1 688 901 990
Nozzle holder   105780-2190
Opening pressure MPa   20.7
Opening pressure kgf/cm2   211
Injection pipe
Outer diameter - inner diameter - length (mm)
mm   6-2-600
Overflow valve   131425-0320
Overflow valve opening pressure kPa   108 88 128
Overflow valve opening pressure kgf/cm2   1.1 0.9 1.3
Tester oil delivery pressure kPa   255 255 255
Tester oil delivery pressure kgf/cm2   2.6 2.6 2.6
Direction of rotation (viewed from drive side)
Left
  L
Injection timing adjustment
Direction of rotation (viewed from drive side)
Left
  L
Injection order   1-2-4-5- 3
Pre-stroke mm   4 3.97 4.03
Beginning of injection position
Governor side
  NO.1
Difference between angles 1
Cyl.1-2
deg.   72 71.75 72.25
Difference between angles 2
Cal 1-4
deg.   144 143.75 144.25
Difference between angles 3
Cal 1-5
deg.   216 215.75 216.25
Difference between angles 4
Cal 1-3
deg.   288 287.75 288.25
Injection quantity adjustment
Adjusting point   -
Rack position   12.2
Pump speed r/min   850 850 850
Average injection quantity mm3/st.   100 98.4 101.6
Max. variation between cylinders %   0 -3.5 3.5
Basic   *
Fixing the rack   *
Standard for adjustment of the maximum variation between cylinders   *
Injection quantity adjustment_02
Adjusting point   Z
Rack position   9.5+-0.5
Pump speed r/min   415 415 415
Each cylinder's injection qty mm3/st.   12 11 13
Fixing the rack   *
Standard for adjustment of the maximum variation between cylinders   *
Injection quantity adjustment_03
Adjusting point   A
Rack position   R1(12.2)
Pump speed r/min   850 850 850
Average injection quantity mm3/st.   100 99 101
Basic   *
Fixing the lever   *
Injection quantity adjustment_04
Adjusting point   B
Rack position   R1+0.6
Pump speed r/min   1450 1450 1450
Average injection quantity mm3/st.   103 99 107
Fixing the lever   *
Injection quantity adjustment_05
Adjusting point   C
Rack position   R1+0.45
Pump speed r/min   1160 1160 1160
Average injection quantity mm3/st.   105.5 101.5 109.5
Fixing the lever   *
Injection quantity adjustment_06
Adjusting point   D
Rack position   R1-0.75
Pump speed r/min   580 580 580
Average injection quantity mm3/st.   84 80 88
Fixing the lever   *
Injection quantity adjustment_07
Adjusting point   E
Rack position   R1-0.9
Pump speed r/min   300 300 300
Average injection quantity mm3/st.   77 71 83
Fixing the lever   *
Injection quantity adjustment_08
Adjusting point   I
Rack position   -
Pump speed r/min   100 100 100
Average injection quantity mm3/st.   170 170 180
Fixing the lever   *
Rack limit   *
Timer adjustment
Pump speed r/min   950--
Advance angle deg.   0 0 0
Load   1/5
Remarks
Start
 
Timer adjustment_02
Pump speed r/min   900
Advance angle deg.   0.3
Load   1/5
Timer adjustment_03
Pump speed r/min   -
Advance angle deg.   1 0.7 1.3
Load   5/5
Remarks
Measure the actual speed.
 
Timer adjustment_04
Pump speed r/min   1190++
Advance angle deg.   1 0.7 1.3
Load   2/5
Timer adjustment_05
Pump speed r/min   (1300-50 )
Advance angle deg.   1 0.7 1.3
Load   5/5
Remarks
Measure the actual speed.
 
Timer adjustment_06
Pump speed r/min   1450-50
Advance angle deg.   5.5 5.2 5.8
Load   5/5
Remarks
Finish
 

Test data Ex:

Governor adjustment

Test data 101501-2040
N:Pump speed R:Rack position (mm) (1)Torque cam stamping: T1 (2)Tolerance for racks not indicated: +-0.05mm. (3)RACK LIMIT
----------
T1=L71
----------

Speed control lever angle

Test data 101501-2040
F:Full speed I:Idle (1)Use the hole at R = aa (2)Stopper bolt set position 'H'
----------
aa=41mm
----------
a=8deg+-5deg b=(39deg)+-3deg

Stop lever angle

Test data 101501-2040
N:Pump normal S:Stop the pump. (1)Use the hole at R = aa (2)Set the stopper bolt at speed = bb and rack position = cc (non-injection rack position). Confirm non-injection. (3)After setting the stopper screw, confirm non-injection at N = dd and R = actual rack position. After setting apply red paint.
----------
aa=38mm bb=1580r/min cc=6.8-0.5mm dd=300r/min
----------
a=0deg+-5deg b=(28deg)+-5deg

Timing setting

Test data 101501-2040
(1)Pump vertical direction (2)Coupling's key groove position at No 1 cylinder's beginning of injection (3)- (4)-
----------

----------
a=(20deg)




Have questions with 101501-2040?





Group cross 101501-2040 ZEXEL

Hino 

 
220008690A 
INJECTION-PUMP ASSEMBLY
J07C
 
220008690B 
INJECTION-PUMP ASSEMBLY
J07C
 
220008691A 
INJECTION-PUMP ASSEMBLY
 
 
INJECTION-PUMP ASSEMBLY

Hino 

F 019 Z10 106 
220008691B 
INJECTION-PUMP ASSEMBLY
J07C
 
220008700A 
INJECTION-PUMP ASSEMBLY
J07C
 
 
INJECTION-PUMP ASSEMBLY
 
 
INJECTION-PUMP ASSEMBLY

Hino 

 
220008701B 
INJECTION-PUMP ASSEMBLY
J07C
 
220008710A 
INJECTION-PUMP ASSEMBLY
J07C
 
220008710B 
INJECTION-PUMP ASSEMBLY
J07C
 
220008711B 
INJECTION-PUMP ASSEMBLY
J07C
 
 
INJECTION-PUMP ASSEMBLY

Hino 

 
220008711C 
INJECTION-PUMP ASSEMBLY
J07C
 
 
INJECTION-PUMP ASSEMBLY

Hino 

9 400 610 562 
220009040A 
INJECTION-PUMP ASSEMBLY
J07C
101501-2040  

101501-2041 
 
220009230A 
INJECTION-PUMP ASSEMBLY
J07C
 
220009231A 
INJECTION-PUMP ASSEMBLY
J07C
F 01G 09U 02S 
220009232A 
INJECTION-PUMP ASSEMBLY
J07C
F 01G 09U 02T 
220009233A 
INJECTION-PUMP ASSEMBLY
J07C
 
220009730A 
INJECTION-PUMP ASSEMBLY
J07C
 
 
INJECTION-PUMP ASSEMBLY

Hino 

F 019 Z20 453 
220009731A 
INJECTION-PUMP ASSEMBLY
J07C
9 400 614 550 
220009732A 
INJECTION-PUMP ASSEMBLY
J07C
 
220009740A 
INJECTION-PUMP ASSEMBLY
J07C
 
 
INJECTION-PUMP ASSEMBLY

Hino 

 
220009741A 
INJECTION-PUMP ASSEMBLY
J07C
9 400 614 551 
220009742A 
INJECTION-PUMP ASSEMBLY
J07C
 
 
INJECTION-PUMP ASSEMBLY

Hino 

9 400 619 754 
220009750A 
INJECTION-PUMP ASSEMBLY
J07C
9 400 619 909 
220009751A 
INJECTION-PUMP ASSEMBLY
J07C
F 019 Z20 454 
220009760A 
INJECTION-PUMP ASSEMBLY
J07C
9 400 619 910 
220009761A 
INJECTION-PUMP ASSEMBLY
J07C
Back to top