101452-3122 ZEXEL INJECTION-PUMP ASSEMBLY Calibration Data 1014523122

Information Cross number Calibration Data Calibration Data Ex

Price: query
Buy now
Add to cart Go to cart

Rating:

Buy INJECTION-PUMP ASSEMBLY 101452-3122 zexel genuine, new aftermarket engine parts with delivery

Information injection-pump assembly

ZEXEL 101452-3122 1014523122

Cross reference number

ZEXEL 101452-3122 1014523122

Zexel num

Bosch num

Firm num

Name

101452-3122

INJECTION-PUMP ASSEMBLY

Calibration Data:

Adjustment conditions

Test oil
1404 Test oil ISO4113 or {SAEJ967d}

Test oil temperature degC 40 40 45

Nozzle and nozzle holder 105780-8140

Bosch type code EF8511/9A

Nozzle 105780-0000

Bosch type code DN12SD12T

Nozzle holder 105780-2080

Bosch type code EF8511/9

Opening pressure MPa 17.2

Opening pressure kgf/cm2 175

Injection pipe
Outer diameter - inner diameter - length (mm) mm 6-2-600

Tester oil delivery pressure kPa 157 157 157

Tester oil delivery pressure kgf/cm2 1.6 1.6 1.6

Direction of rotation (viewed from drive side)
Right R

Injection timing adjustment

Direction of rotation (viewed from drive side)
Right R

Injection order 1-2-4-3

Pre-stroke mm 1.5 1.45 1.55

Beginning of injection position
Drive side NO.1

Difference between angles 1
Cyl.1-2 deg. 90 89.5 90.5

Difference between angles 2
Cal 1-4 deg. 180 179.5 180.5

Difference between angles 3
Cal 1-3 deg. 270 269.5 270.5

Injection quantity adjustment

Adjusting point A

Rack position 12

Pump speed r/min 900 900 900

Average injection quantity mm3/st. 45.8 44.8 46.8

Max. variation between cylinders % 0 -2.5 2.5

Basic *

Fixing the lever *

Injection quantity adjustment_02

Adjusting point -

Rack position 8.3+-0.5

Pump speed r/min 400 400 400

Average injection quantity mm3/st. 11 10 12

Max. variation between cylinders % 0 -15 15

Fixing the rack *

Remarks
Adjust only variation between cylinders; adjust governor according to governor specifications.

Test data Ex:

Governor adjustment

N:Pump speed R:Rack position (mm) (1)Target notch: K (2)RACK CAP: R1 (3)The torque control spring must does not have a set force. (4)Rack difference between N = N1 and N = N2 (5)Idle sub spring setting: L1.
----------
K=7 R1=(17.5)mm N1=900r/min N2=500r/min L1=6-0.5mm
----------

Speed control lever angle

F:Full speed I:Idle (1)Set the pump speed at aa. ( At delivery ) (2)Set the pump speed at bb. (3)Stopper bolt setting
----------
aa=955r/min bb=750r/min
----------
a=(1deg)+-5deg b=(26deg)+-5deg c=(7deg)+-5deg

Stop lever angle

N:Pump normal S:Stop the pump. (1)No return spring
----------

----------
a=4deg+-5deg b=53deg+-5deg

Timing setting

(1)Pump vertical direction (2)Position of key groove at No 1 cylinder's beginning of injection (3)Stamp aligning marks on the pump housing flange. (4)- (5)-
----------

----------
a=46deg18min+-3deg b=13deg42min+-30min