101402-3881 ZEXEL INJECTION-PUMP ASSEMBLY Calibration Data 1014023881

Information Cross number Calibration Data Calibration Data Ex

Price: query
Buy now
Add to cart Go to cart

Rating:

Buy INJECTION-PUMP ASSEMBLY 101402-3881 zexel genuine, new aftermarket engine parts with delivery

Information injection-pump assembly

ZEXEL 101402-3881 1014023881

Service parts 101402-3881 INJECTION-PUMP ASSEMBLY:

1. _

2. FUEL INJECTION PUMP 101041-9220

3. GOVERNOR 105404-5180

4. SUPPLY PUMP

105220-5960

5. AUTOM. ADVANCE MECHANIS

6. COUPLING PLATE

7. COUPLING PLATE

8. _

9. _

10. NOZZLE AND HOLDER ASSY

11. Nozzle and Holder

12. Open Pre:MPa(Kqf/cm2) 21.6{220}

13. NOZZLE-HOLDER

14. NOZZLE

15. NOZZLE SET

Include in #1:

101402-3881 as INJECTION-PUMP ASSEMBLY

108822-3286 as _

Cross reference number

ZEXEL 101402-3881 1014023881

Zexel num

Bosch num

Firm num

Name

101402-3881

INJECTION-PUMP ASSEMBLY
14BC PE4A,5A, PE

Calibration Data:

Adjustment conditions

Test oil
1404 Test oil ISO4113 or {SAEJ967d}

Test oil temperature degC 40 40 45

Nozzle and nozzle holder 105780-8140

Bosch type code EF8511/9A

Nozzle 105780-0000

Bosch type code DN12SD12T

Nozzle holder 105780-2080

Bosch type code EF8511/9

Opening pressure MPa 17.2

Opening pressure kgf/cm2 175

Injection pipe
Outer diameter - inner diameter - length (mm) mm 6-2-600

Overflow valve 131424-3420

Overflow valve opening pressure kPa 255 221 289

Overflow valve opening pressure kgf/cm2 2.6 2.25 2.95

Tester oil delivery pressure kPa 157 157 157

Tester oil delivery pressure kgf/cm2 1.6 1.6 1.6

Direction of rotation (viewed from drive side)
Right R

Injection timing adjustment

Direction of rotation (viewed from drive side)
Right R

Injection order 1-3-4-2

Pre-stroke mm 2.5 2.45 2.55

Beginning of injection position
Drive side NO.1

Difference between angles 1
Cal 1-3 deg. 90 89.5 90.5

Difference between angles 2
Cal 1-4 deg. 180 179.5 180.5

Difference between angles 3
Cyl.1-2 deg. 270 269.5 270.5

Injection quantity adjustment

Adjusting point A

Rack position 9.4

Pump speed r/min 1050 1050 1050

Average injection quantity mm3/st. 90 89 91

Max. variation between cylinders % 0 -2.5 2.5

Basic *

Fixing the lever *

Injection quantity adjustment_02

Adjusting point -

Rack position 7.1+-0.5

Pump speed r/min 465 465 465

Average injection quantity mm3/st. 12.5 11.5 13.5

Max. variation between cylinders % 0 -15 15

Fixing the rack *

Remarks
Adjust only variation between cylinders; adjust governor according to governor specifications.

Injection quantity adjustment_03

Adjusting point D

Rack position -

Pump speed r/min 100 100 100

Average injection quantity mm3/st. 90 90 100

Fixing the lever *

Rack limit *

Test data Ex:

Governor adjustment

N:Pump speed R:Rack position (mm) (1)Notch fixed: K (2)Tolerance for racks not indicated: +-0.05mm. (3)The torque control spring does not operate. (4)Adjust the secondary timing before adjusting the governor. (5)RACK LIMIT
----------
K=12
----------

Speed control lever angle

F:Full speed I:Idle S:Stop (1)Speed = aa (push-button power increase) (2)- (3)Speed = bb (active mode) (4)At hole above R = cc (center)
----------
aa=1200r/min bb=1150r/min cc=80mm
----------
a=(17deg)+-3deg b=(34deg)+-5deg c=32deg+-3deg d=(3deg)+-5deg

Timing setting

(1)Pump vertical direction (2)Key groove position at No. 1 cylinder's beginning of injection position (at BTDC: aa). (3)Position of the key groove of the No. 1 cylinder at B.T.D.C. bb (fix the governor flyweight at this position for delivery). (4)B.T.D.C.: aa (5)At second timing adjustment, set the camshaft at the * position and tighten the flyweight locknut. (6)Align the flyweight's timing gear position with the lockpin groove and then fully tighten the flyweight to the camshaft. (7)Remove the lock pin and adjust the governor. Reinstall the lock pin to fix the flyweight for delivery.
----------
aa=16deg bb=0deg
----------
a=54deg54min+-3deg b=8deg+-30min