106871-7560 ZEXEL INJECTION-PUMP ASSEMBLY Calibration Data 1068717560 me090613


106871-7560 INJECTION-PUMP ASSEMBLY
Rating:
62
Buy INJECTION-PUMP ASSEMBLY 106871-7560 zexel genuine, new aftermarket engine parts with delivery

Information injection-pump assembly

ZEXEL 106871-7560 1068717560
MITSUBISHI ME090613 me090613

Cross reference number

ZEXEL 106871-7560 1068717560
MITSUBISHI ME090613 me090613


Zexel num
Bosch num
Firm num
Name
106871-7560 
106871-7700 
 
ME090613  MITSUBISHI
INJECTION-PUMP ASSEMBLY
8DC9 * K

Calibration Data:

Adjustment conditions
Test oil
1404 Test oil
  ISO4113 or {SAEJ967d}
Test oil temperature degC   40 40 45
Nozzle and nozzle holder   105780-8140
Bosch type code   EF8511/9A
Nozzle   105780-0000
Bosch type code   DN12SD12T
Nozzle holder   105780-2080
Bosch type code   EF8511/9
Opening pressure MPa   17.2
Opening pressure kgf/cm2   175
Injection pipe
Outer diameter - inner diameter - length (mm)
mm   8-3-600
Overflow valve   132424-0620
Overflow valve opening pressure kPa   157 123 191
Overflow valve opening pressure kgf/cm2   1.6 1.25 1.95
Tester oil delivery pressure kPa   157 157 157
Tester oil delivery pressure kgf/cm2   1.6 1.6 1.6
Direction of rotation (viewed from drive side)
Right
  R
Injection timing adjustment
Direction of rotation (viewed from drive side)
Right
  R
Injection order   1-2-7-3- 4-5-6-8
Pre-stroke mm   4.8 4.75 4.85
Beginning of injection position
Governor side
  NO.1
Difference between angles 1
Cyl.1-2
deg.   45 44.5 45.5
Difference between angles 2
Cal 1-7
deg.   90 89.5 90.5
Difference between angles 3
Cal 1-3
deg.   135 134.5 135.5
Difference between angles 4
Cal 1-4
deg.   180 179.5 180.5
Difference between angles 5
Cal 1-5
deg.   225 224.5 225.5
Difference between angles 6
Cal 1-6
deg.   270 269.5 270.5
Difference between angles 7
Cal 1-8
deg.   315 314.5 315.5
Injection quantity adjustment
Adjusting point   -
Rack position   9.5
Pump speed r/min   700 700 700
Each cylinder's injection qty mm3/st.   118 114.5 121.5
Basic   *
Fixing the rack   *
Standard for adjustment of the maximum variation between cylinders   *
Injection quantity adjustment_02
Adjusting point   C
Rack position   6.1+-0.5
Pump speed r/min   225 225 225
Each cylinder's injection qty mm3/st.   20 17 23
Fixing the rack   *
Standard for adjustment of the maximum variation between cylinders   *
Injection quantity adjustment_03
Adjusting point   A
Rack position   R1(9.5)
Pump speed r/min   700 700 700
Average injection quantity mm3/st.   118 117 119
Basic   *
Fixing the lever   *
Injection quantity adjustment_04
Adjusting point   B
Rack position   R1(9.5)
Pump speed r/min   1100 1100 1100
Average injection quantity mm3/st.   124 118.8 129.2
Difference in delivery mm3/st.   10.4 10.4 10.4
Fixing the lever   *
Injection quantity adjustment_05
Adjusting point   E
Rack position   -
Pump speed r/min   100 100 100
Average injection quantity mm3/st.   155 135 175
Fixing the lever   *
Remarks
After startup boost setting
 

Test data Ex:

Governor adjustment

Test data 106871-7560
N:Pump speed R:Rack position (mm) (1)Excess fuel setting for starting: SXL (2)Damper spring setting: DL
----------
SXL=10.4+-0.1mm DL=4.3-0.2mm
----------

Timer adjustment

Test data 106871-7560
(1)Adjusting range (2)Step response time (N): Speed of the pump (L): Load (theta) Advance angle (Srd1) Step response time 1 (Srd2) Step response time 2 1. Adjusting conditions for the variable timer (1)Adjust the clearance between the pickup and the protrusion to L.
----------
L=1-0.2mm N2=800r/min C2=(8.8)deg t1=2.5--sec. t2=2.5--sec.
----------
N1=750++r/min P1=0kPa(0kgf/cm2) P2=392kPa(4kgf/cm2) C1=8.8+-0.3deg R01=0/4load R02=4/4load

Speed control lever angle

Test data 106871-7560
F:Full speed
----------

----------
a=21deg+-5deg

0000000901

Test data 106871-7560
F:Full load I:Idle (1)Stopper bolt setting
----------

----------
a=10deg+-5deg b=26deg+-3deg

Stop lever angle

Test data 106871-7560
N:Pump normal S:Stop the pump. (1)Rack position = aa (2)Stopper bolt setting (3)Rack position bb (4)Free (at shipping)
----------
aa=4-0.5mm bb=11.7mm
----------
a=43deg+7deg-5deg b=21.5deg+-5deg c=(10.5deg)

0000001501 MICRO SWITCH

Adjustment of the micro-switch Adjust the bolt to obtain the following lever position when the micro-switch is ON. (1)Speed N1 (2)Rack position Ra
----------
N1=325+-5r/min Ra=5.6mm
----------

0000001601 RACK SENSOR

Test data 106871-7560
V1:Supply voltage V2f:Full side output voltage V2i:Idle side output voltage (A) Black (B) Yellow (C) Red (D) Trimmer (E): Shaft (F) Nut (G) Load lever 1. Load sensor adjustment (1)Connect as shown in the above diagram and apply supply voltage V1. (2)Hold the load lever (G) against the full side. (3)Turn the shaft so that the voltage between (A) and (B) is V2. (4)Hold the load lever (G) against the idle side. (5)Adjust (D) so that the voltage between (A) and (B) is V2i. (6)Repeat the above adjustments. (7)Tighten the nut (F) at the point satisfying the standards. (8)Hold the load lever against the full side stopper and the idle side stopper. (9)At this time, confirm that the full side output voltage is V2f and the idle side output voltage is V2i.
----------
V1=5+-0.02V V2f=0.15+0.03V V2i=2.35-0.03V
----------

Timing setting

Test data 106871-7560
(1)Pump vertical direction (2)Coupling's key groove position at No 1 cylinder's beginning of injection (3)- (4)-
----------

----------
a=(40deg)




Have questions with 106871-7560?





Group cross 106871-7560 ZEXEL

Mitsubishi 

 
 
INJECTION-PUMP ASSEMBLY
8DC91T2
9 400 618 214 
ME065937 
INJECTION-PUMP ASSEMBLY
8DC91T2
9 400 618 215 
ME090372 
INJECTION-PUMP ASSEMBLY
8DC82
 
ME065940 
INJECTION-PUMP ASSEMBLY
8DC91
 
ME065941 
INJECTION-PUMP ASSEMBLY
8DC91
 
ME065942 
INJECTION-PUMP ASSEMBLY
8DC91
9 400 618 216 
ME090467 
INJECTION-PUMP ASSEMBLY
8DC82
106871-7560  

106871-7700 
 
ME090613 
INJECTION-PUMP ASSEMBLY
8DC9
 
 
INJECTION-PUMP ASSEMBLY

Mitsubishi 

9 400 618 217 
ME065921 
INJECTION-PUMP ASSEMBLY
8DC82
9 400 618 218 
ME090645 
INJECTION-PUMP ASSEMBLY
8DC9T2
9 400 618 219 
ME090641 
INJECTION-PUMP ASSEMBLY
8DC9T7
Back to top