106671-7030 ZEXEL 9 400 616 924 BOSCH INJECTION-PUMP ASSEMBLY 9400616924 1066717030 me056462


106671-7030 INJECTION-PUMP ASSEMBLY
Rating:
73
Buy INJECTION-PUMP ASSEMBLY 106671-7030 zexel genuine, new aftermarket engine parts with delivery

Information injection-pump assembly

BOSCH 9 400 616 924 9400616924
ZEXEL 106671-7030 1066717030
MITSUBISHI ME056462 me056462

Service parts 106671-7030 INJECTION-PUMP ASSEMBLY:

1. _
2. FUEL INJECTION PUMP 106067-7830
3. GOVERNOR 105487-1930
4. SUPPLY PUMP 105207-1330
5. AUTOM. ADVANCE MECHANIS 105636-0920
6. COUPLING PLATE 105662-0710
7. COUPLING PLATE
8. _
9. _
10. NOZZLE AND HOLDER ASSY 105100-5820
11. Nozzle and Holder ME056329
12. Open Pre:MPa(Kqf/cm2) 17.7{180}/21.6{220}
13. NOZZLE-HOLDER 105031-4530
14. NOZZLE 105015-5390
15. NOZZLE SET

Include in #1:

106671-7030 as INJECTION-PUMP ASSEMBLY

Cross reference number

BOSCH 9 400 616 924 9400616924
ZEXEL 106671-7030 1066717030
MITSUBISHI ME056462 me056462


Zexel num
Bosch num
Firm num
Name
106671-7030 
106671-7410 
9 400 616 924 
ME056462  MITSUBISHI
INJECTION-PUMP ASSEMBLY
6D22 K

Calibration Data:

Adjustment conditions
Test oil
1404 Test oil
  ISO4113 or {SAEJ967d}
Test oil temperature degC   40 40 45
Nozzle and nozzle holder   105780-8140
Bosch type code   EF8511/9A
Nozzle   105780-0000
Bosch type code   DN12SD12T
Nozzle holder   105780-2080
Bosch type code   EF8511/9
Opening pressure MPa   17.2
Opening pressure kgf/cm2   175
Injection pipe
Outer diameter - inner diameter - length (mm)
mm   8-3-600
Overflow valve   131424-4620
Overflow valve opening pressure kPa   255 221 289
Overflow valve opening pressure kgf/cm2   2.6 2.25 2.95
Tester oil delivery pressure kPa   157 157 157
Tester oil delivery pressure kgf/cm2   1.6 1.6 1.6
Direction of rotation (viewed from drive side)
Right
  R
Injection timing adjustment
Direction of rotation (viewed from drive side)
Right
  R
Injection order   1-5-3-6- 2-4
Pre-stroke mm   4.8 4.75 4.85
Beginning of injection position
Governor side
  NO.1
Difference between angles 1
Cal 1-5
deg.   60 59.5 60.5
Difference between angles 2
Cal 1-3
deg.   120 119.5 120.5
Difference between angles 3
Cal 1-6
deg.   180 179.5 180.5
Difference between angles 4
Cyl.1-2
deg.   240 239.5 240.5
Difference between angles 5
Cal 1-4
deg.   300 299.5 300.5
Injection quantity adjustment
Adjusting point   -
Rack position   7.9
Pump speed r/min   700 700 700
Each cylinder's injection qty mm3/st.   104 101.4 106.6
Basic   *
Fixing the rack   *
Standard for adjustment of the maximum variation between cylinders   *
Injection quantity adjustment_02
Adjusting point   F
Rack position   5+-0.5
Pump speed r/min   500 500 500
Each cylinder's injection qty mm3/st.   16.5 14 19
Fixing the rack   *
Standard for adjustment of the maximum variation between cylinders   *
Injection quantity adjustment_03
Adjusting point   A
Rack position   R1(7.9)
Pump speed r/min   700 700 700
Average injection quantity mm3/st.   104 103 105
Basic   *
Fixing the lever   *
Injection quantity adjustment_04
Adjusting point   B
Rack position   R1(7.9)
Pump speed r/min   1100 1100 1100
Average injection quantity mm3/st.   118 114 122
Difference in delivery mm3/st.   8 8 8
Fixing the lever   *
Injection quantity adjustment_05
Adjusting point   C
Rack position   5.7+-0.5
Pump speed r/min   225 225 225
Each cylinder's injection qty mm3/st.   16.5 14 19
Fixing the rack   *
Remarks
(check)
 
Injection quantity adjustment_06
Adjusting point   E
Rack position   -
Pump speed r/min   100 100 100
Average injection quantity mm3/st.   150 130 170
Fixing the lever   *
Timer adjustment
Pump speed r/min   950
Advance angle deg.   0.5
Timer adjustment_02
Pump speed r/min   1050
Advance angle deg.   2.2 1.7 2.7
Timer adjustment_03
Pump speed r/min   1150
Advance angle deg.   5.5 5 6
Remarks
Finish
 

Test data Ex:

Governor adjustment

Test data 106671-7030
N:Pump speed R:Rack position (mm) (1)Lever ratio: RT (2)Target shim dimension: TH (3)Damper spring setting: DL (4)Excess fuel setting for starting: SXL
----------
RT=1 TH=2.6mm DL=4.5-0.2mm SXL=R1+0.2mm
----------

Speed control lever angle

Test data 106671-7030
F:Full speed
----------

----------
a=27deg+-5deg

0000000901

Test data 106671-7030
F:Full load I:Idle (1)Stopper bolt setting
----------

----------
a=23deg+-3deg b=24deg+-5deg

Stop lever angle

Test data 106671-7030
N:Pump normal S:Stop the pump. (1)Rack position = aa (2)Set stopper bolt so that rack position = bb. (3)Free (at shipping)
----------
aa=16.6mm bb=4.1-0.5mm
----------
a=35deg+-5deg b=61.5deg+7deg-5deg c=(6deg)

0000001501 MICRO SWITCH

Adjustment of the micro-switch Adjust the bolt to obtain the following lever position when the micro-switch is ON. (1)Speed N1 (2)Rack position Ra
----------
N1=325+-5r/min Ra=5.4mm
----------

Timing setting

Test data 106671-7030
(1)Pump vertical direction (2)Coupling's key groove position at No 1 cylinder's beginning of injection (3)- (4)-
----------

----------
a=(7deg)




Have questions with 106671-7030?





Group cross 106671-7030 ZEXEL

Mitsubishi 

9 400 616 921 
ME056448 
INJECTION-PUMP ASSEMBLY
6D22
9 400 616 922 
ME059642 
INJECTION-PUMP ASSEMBLY
6D22PT
 
 
INJECTION-PUMP ASSEMBLY
6D22T2
9 400 616 923 
ME056447 
INJECTION-PUMP ASSEMBLY
6D22T2
106671-7030  

106671-7410 
9 400 616 924 
ME056462 
INJECTION-PUMP ASSEMBLY
6D22
 
ME056463 
INJECTION-PUMP ASSEMBLY
6D22
9 400 616 925 
ME056464 
INJECTION-PUMP ASSEMBLY
6D22
 
ME056465 
INJECTION-PUMP ASSEMBLY
6D22

Mitsubishi-Heav 

 
3626500170 
INJECTION-PUMP ASSEMBLY
S6B

Mitsubishi 

 
 
INJECTION-PUMP ASSEMBLY
6D22T3
9 400 616 926 
ME056466 
INJECTION-PUMP ASSEMBLY
6D22T3
 
ME059672 
INJECTION-PUMP ASSEMBLY
6D22TC
Back to top