106671-5720 ZEXEL 9 400 616 873 BOSCH INJECTION-PUMP ASSEMBLY 9400616873 1066715720 1671496500


106671-5720 INJECTION-PUMP ASSEMBLY
Rating:
65
Buy INJECTION-PUMP ASSEMBLY 106671-5720 zexel genuine, new aftermarket engine parts with delivery

Information injection-pump assembly

BOSCH 9 400 616 873 9400616873
ZEXEL 106671-5720 1066715720
NISSAN-DIESEL 1671496500 1671496500

Service parts 106671-5720 INJECTION-PUMP ASSEMBLY:

1. _
2. FUEL INJECTION PUMP 106067-1550
3. GOVERNOR 105489-5770
4. SUPPLY PUMP 105217-1850
5. AUTOM. ADVANCE MECHANIS 105636-2720
6. COUPLING PLATE 105662-1200
7. COUPLING PLATE
8. _
9. _
10. NOZZLE AND HOLDER ASSY 105101-5600
11. Nozzle and Holder 16600-96520
12. Open Pre:MPa(Kqf/cm2) 22.6{230}
13. NOZZLE-HOLDER 105031-4370
14. NOZZLE 105015-6340
15. NOZZLE SET

Include in #1:

106671-5720 as INJECTION-PUMP ASSEMBLY

Cross reference number

BOSCH 9 400 616 873 9400616873
ZEXEL 106671-5720 1066715720
NISSAN-DIESEL 1671496500 1671496500


Zexel num
Bosch num
Firm num
Name
106671-5720 
9 400 616 873 
1671496500  NISSAN-DIESEL
INJECTION-PUMP ASSEMBLY
PE6TA K

Calibration Data:

Adjustment conditions
Test oil
1404 Test oil
  ISO4113 or {SAEJ967d}
Test oil temperature degC   40 40 45
Nozzle and nozzle holder   105780-8140
Bosch type code   EF8511/9A
Nozzle   105780-0000
Bosch type code   DN12SD12T
Nozzle holder   105780-2080
Bosch type code   EF8511/9
Opening pressure MPa   17.2
Opening pressure kgf/cm2   175
Injection pipe
Outer diameter - inner diameter - length (mm)
mm   8-3-600
Overflow valve   132424-0620
Overflow valve opening pressure kPa   157 123 191
Overflow valve opening pressure kgf/cm2   1.6 1.25 1.95
Tester oil delivery pressure kPa   157 157 157
Tester oil delivery pressure kgf/cm2   1.6 1.6 1.6
Direction of rotation (viewed from drive side)
Right
  R
Injection timing adjustment
Direction of rotation (viewed from drive side)
Right
  R
Injection order   1-4-2-6- 3-5
Pre-stroke mm   3.65 3.6 3.7
Beginning of injection position
Drive side
  NO.1
Difference between angles 1
Cal 1-4
deg.   60 59.5 60.5
Difference between angles 2
Cyl.1-2
deg.   120 119.5 120.5
Difference between angles 3
Cal 1-6
deg.   180 179.5 180.5
Difference between angles 4
Cal 1-3
deg.   240 239.5 240.5
Difference between angles 5
Cal 1-5
deg.   300 299.5 300.5
Injection quantity adjustment
Adjusting point   A
Rack position   11.8
Pump speed r/min   650 650 650
Average injection quantity mm3/st.   166.5 164.5 168.5
Max. variation between cylinders %   0 -4 4
Basic   *
Fixing the lever   *
Boost pressure kPa   76 76
Boost pressure mmHg   570 570
Solenoid boost comp. OFF   *
Injection quantity adjustment_02
Adjusting point   C
Rack position   6.7+-0.5
Pump speed r/min   270 270 270
Average injection quantity mm3/st.   15.5 14.5 16.5
Max. variation between cylinders %   0 -10 10
Fixing the rack   *
Boost pressure kPa   0 0 0
Boost pressure mmHg   0 0 0
Solenoid boost comp. OFF   *
Injection quantity adjustment_03
Adjusting point   D
Rack position   9.75
Pump speed r/min   400 400 400
Average injection quantity mm3/st.   110 107 113
Fixing the lever   *
Boost pressure kPa   0 0 0
Boost pressure mmHg   0 0 0
Solenoid boost comp. OFF   *
Boost compensator adjustment
Pump speed r/min   400 400 400
Rack position   9.75
Boost pressure kPa   20 18.7 21.3
Boost pressure mmHg   150 140 160
Boost compensator adjustment_02
Pump speed r/min   400 400 400
Rack position   11.8
Boost pressure kPa   46 42 50
Boost pressure mmHg   345 315 375
Boost compensator adjustment_03
Pump speed r/min   400 400 400
Rack position   (12.8)
Boost pressure kPa   62.7 62.7 62.7
Boost pressure mmHg   470 470 470
Timer adjustment
Pump speed r/min   875--
Advance angle deg.   0 0 0
Remarks
Start
 
Timer adjustment_02
Pump speed r/min   825
Advance angle deg.   0.5
Timer adjustment_03
Pump speed r/min   925
Advance angle deg.   1 0.5 1.5
Remarks
Finish
 

Test data Ex:

Governor adjustment

Test data 106671-5720
N:Pump speed R:Rack position (mm) (1)Lever ratio: RT (2)Target shim dimension: TH (3)Tolerance for racks not indicated: +-0.05mm. (4)Solenoid boost compensator OFF: SBL (5)Rack limit using the stop lever: SRL (6)Boost compensator stroke: BCL (7)Damper spring setting (8)Rack difference between N = N1 and N = N2 (9)Variable speed specification: idling adjustment (10)Fix the lever at the full-load position at delivery. (11)Main spring setting
----------
RT=1 TH=2.2mm SBL=(13.3)mm SRL=12.8+0.2mm BCL=(3.05)mm N1=1100r/min N2=650r/min
----------

Speed control lever angle

Test data 106671-5720
F:Full speed I:Idle (1)Pump speed = aa (2)Set the stopper bolt (fixed at full-load position at delivery.)
----------
aa=290r/min
----------
a=(16deg)+-5deg b=(8deg)+-5deg

0000000901

Test data 106671-5720
F:Full load I:Idle (1)Stopper bolt setting (2)Use the hole at R = aa
----------
aa=42mm
----------
a=31deg+-3deg b=45deg+-5deg

Stop lever angle

Test data 106671-5720
N:Pump normal S:Stop the pump. (1)Rack position aa (pump speed bb r/min ) (2)Use the pin above R = cc
----------
aa=12.8+0.2mm bb=350r/min cc=40mm
----------
a=(42deg)+-5deg b=41deg+-5deg

0000001501 BCS

Test data 106671-5720
(A) Screw for precise adjustment (B) Pre-adjustment screw (C) Control rack, rack decrease direction (D) Rack limit 1. Solenoid boost compensator adjustment (1)Supply DC: V1 to the solenoid terminals and confirm solenoid operation. (2)With the solenoid ON, calculate L1 from the value of R1. [L1 = La - (10.5 - R1) +-0.2] (3)Adjust (B) to obtain L1. (4)Assemble the solenoid to the governor. (5)With the solenoid ON, readjust (B) so that R1 is within the allowance a. (6)With the solenoid OFF, perform all governor adjustments except rack limit adjustment. (7)Set the pump speed at N1 and turn the solenoid ON. (8)Adjust (A) so that R1 is within the allowance range a. (9)Set the pump speed at N1 and fix the load lever in the full position (10)Turn the solenoid switch ON and OFF several times and confirm that the difference in rack positions is within L2. (11)Set the rack limit. (12)Stamp the solenoid valve.
----------
V1=24 V N1=400r/min N2=0r/min R1=9.3mm a=+-0.5mm L1=26.8+-0.2mm L2=3.5~5mm
----------

Timing setting

Test data 106671-5720
(1)Pump vertical direction (2)Coupling's key groove position at No 1 cylinder's beginning of injection (3)- (4)-
----------

----------
a=(30deg)




Have questions with 106671-5720?





Group cross 106671-5720 ZEXEL

Nissan-Diesel 

9 400 616 872 
1671496502 
INJECTION-PUMP ASSEMBLY
PE6TE
9 400 619 956 
1671496503 
INJECTION-PUMP ASSEMBLY
PE6T
106671-5720  
9 400 616 873 
1671496500 
INJECTION-PUMP ASSEMBLY
PE6TA
9 400 616 874 
1671496501 
INJECTION-PUMP ASSEMBLY
PE6TA
9 400 616 875 
1671396978 
INJECTION-PUMP ASSEMBLY
PE6T
 
 
INJECTION-PUMP ASSEMBLY
 
 
INJECTION-PUMP ASSEMBLY
 
 
INJECTION-PUMP ASSEMBLY

Nissan-Diesel 

9 400 616 876 
1680196671 
INJECTION-PUMP ASSEMBLY
PF6TA
F 01G 09U 07F 
 
INJECTION-PUMP ASSEMBLY
F 01G 09U 07G 
 
INJECTION-PUMP ASSEMBLY

Nissan-Diesel 

9 400 616 877 
1680195511 
INJECTION-PUMP ASSEMBLY
NF6TA
9 400 616 878 
1671396976 
INJECTION-PUMP ASSEMBLY
PF6TA
9 400 616 879 
1679096609 
INJECTION-PUMP ASSEMBLY
PF6T24
9 400 612 663 
1671396979 
INJECTION-PUMP ASSEMBLY
PF6TA
Back to top