106671-3484 ZEXEL 9 400 610 111 BOSCH INJECTION-PUMP ASSEMBLY 9400610111 1066713484 220003635a


106671-3484 INJECTION-PUMP ASSEMBLY
Rating:
43
Buy INJECTION-PUMP ASSEMBLY 106671-3484 zexel genuine, new aftermarket engine parts with delivery

Information injection-pump assembly

BOSCH 9 400 610 111 9400610111
ZEXEL 106671-3484 1066713484
HINO 220003635A 220003635a

Service parts 106671-3484 INJECTION-PUMP ASSEMBLY:

1. _
2. FUEL INJECTION PUMP 106067-7511
3. GOVERNOR 105488-8600
4. SUPPLY PUMP 105217-1301
5. AUTOM. ADVANCE MECHANIS 105635-0041
6. COUPLING PLATE 105662-0500
7. COUPLING PLATE
8. _
9. _
10. NOZZLE AND HOLDER ASSY 105100-5031
11. Nozzle and Holder 23600-1221A
12. Open Pre:MPa(Kqf/cm2) 21.6{220}
13. NOZZLE-HOLDER 105031-5300
14. NOZZLE 105015-4640
15. NOZZLE SET

Include in #1:

106671-3484 as INJECTION-PUMP ASSEMBLY

Cross reference number

BOSCH 9 400 610 111 9400610111
ZEXEL 106671-3484 1066713484
HINO 220003635A 220003635a


Zexel num
Bosch num
Firm num
Name
106671-3484 
9 400 610 111 
220003635A  HINO
INJECTION-PUMP ASSEMBLY
EK100 * K 14CA PE6P,6PD PE

Calibration Data:

Adjustment conditions
Test oil
1404 Test oil
  ISO4113 or {SAEJ967d}
Test oil temperature degC   40 40 45
Nozzle and nozzle holder   105780-8140
Bosch type code   EF8511/9A
Nozzle   105780-0000
Bosch type code   DN12SD12T
Nozzle holder   105780-2080
Bosch type code   EF8511/9
Opening pressure MPa   17.2
Opening pressure kgf/cm2   175
Injection pipe
Outer diameter - inner diameter - length (mm)
mm   8-3-600
Overflow valve   134424-0920
Overflow valve opening pressure kPa   162 147 177
Overflow valve opening pressure kgf/cm2   1.65 1.5 1.8
Tester oil delivery pressure kPa   157 157 157
Tester oil delivery pressure kgf/cm2   1.6 1.6 1.6
Direction of rotation (viewed from drive side)
Left
  L
Injection timing adjustment
Direction of rotation (viewed from drive side)
Left
  L
Injection order   1-4-2-6- 3-5
Pre-stroke mm   3.3 3.2 3.3
Beginning of injection position
Drive side
  NO.1
Difference between angles 1
Cal 1-4
deg.   60 59.5 60.5
Difference between angles 2
Cyl.1-2
deg.   120 119.5 120.5
Difference between angles 3
Cal 1-6
deg.   180 179.5 180.5
Difference between angles 4
Cal 1-3
deg.   240 239.5 240.5
Difference between angles 5
Cal 1-5
deg.   300 299.5 300.5
Injection quantity adjustment
Adjusting point   A
Rack position   9.95
Pump speed r/min   500 500 500
Average injection quantity mm3/st.   114.5 111.5 117.5
Max. variation between cylinders %   0 -4 4
Fixing the lever   *
Injection quantity adjustment_02
Adjusting point   B
Rack position   10.3
Pump speed r/min   700 700 700
Average injection quantity mm3/st.   127.7 125.7 129.7
Max. variation between cylinders %   0 -2 2
Basic   *
Fixing the lever   *
Injection quantity adjustment_03
Adjusting point   C
Rack position   10.75
Pump speed r/min   1150 1150 1150
Average injection quantity mm3/st.   134.7 131.7 137.7
Max. variation between cylinders %   0 -4 4
Fixing the lever   *
Injection quantity adjustment_04
Adjusting point   D
Rack position   7+-0.5
Pump speed r/min   225 225 225
Average injection quantity mm3/st.   15 12 18
Max. variation between cylinders %   0 -15 15
Fixing the rack   *
Injection quantity adjustment_05
Adjusting point   E
Rack position   -
Pump speed r/min   100 100 100
Average injection quantity mm3/st.   126.3 119.3 133.3
Fixing the lever   *
Rack limit   *
Timer adjustment
Pump speed r/min   700+-50
Advance angle deg.   0 0 0
Remarks
Start
 
Timer adjustment_02
Pump speed r/min   900
Advance angle deg.   1.4 0.9 1.9
Timer adjustment_03
Pump speed r/min   1150
Advance angle deg.   4 3.5 4.5
Remarks
Finish
 

Test data Ex:

Governor adjustment

Test data 106671-3484
N:Pump speed R:Rack position (mm) (1)Lever ratio: RT (2)Target shim dimension: TH (3)Tolerance for racks not indicated: +-0.05mm. (4)RACK LIMIT (5)Damper spring setting
----------
RT=1 TH=1.5mm
----------

Speed control lever angle

Test data 106671-3484
F:Full speed
----------

----------
a=3deg+-5deg

0000000901

Test data 106671-3484
F:Full load I:Idle (1)Stopper bolt setting
----------

----------
a=10deg+-5deg b=24.5deg+-3deg

Stop lever angle

Test data 106671-3484
N:Pump normal S:Stop the pump.
----------

----------
a=15deg+-5deg b=64deg+-5deg

0000001501 GOVERNOR TORQUE CONTROL

Test data 106671-3484
Dr:Torque control stroke (A): Without torque control spring capsule 1. Adjustment procedures (1)Procedure is the same as that for the RFD (former type), except that the positive torque control stroke must be determined at the full lever setting. 2. Procedures for adjustment (1)Remove the torque control spring capsule. (2)Operate the pump at approximately N1. (End of idling spring operation < N1.) (3)Tilt the lever to the full side. (4)Set so that R = RF. (5)Increase the speed by pushing in the screw (attached to the bracket on the rear of the tension lever) through the adjusting window. (6)Adjust so that the torque control stroke Dr1 can be obtained. (7)Align N2 and N3 with the torque control spring capsule. 3. Final confirmation (1)After final confirmation, temporarily set the load lever to N = N1, R = idling position. (2)From this condition, increase speed to N = N4. (3)Confirm that positive torque control stroke is Dr2.
----------
N1=500r/min N2=- N3=- N4=900r/min RF=9.95mm Dr1=0.8mm Dr2=0+0.3mm
----------

Timing setting

Test data 106671-3484
(1)Pump vertical direction (2)Coupling's key groove position at No 1 cylinder's beginning of injection (3)- (4)-
----------

----------
a=(0deg)




Have questions with 106671-3484?





Group cross 106671-3484 ZEXEL

Hino 

 
220201510A 
INJECTION-PUMP ASSEMBLY
EK100TI
 
220201512A 
INJECTION-PUMP ASSEMBLY
EK100TI
 
220201520A 
INJECTION-PUMP ASSEMBLY
EK100
 
220201523A 
INJECTION-PUMP ASSEMBLY
EK100
 
 
INJECTION-PUMP ASSEMBLY

Hino 

 
220201524A 
INJECTION-PUMP ASSEMBLY
9 400 616 769 
220201524A 
INJECTION-PUMP ASSEMBLY
EK100
 
220003710A 
INJECTION-PUMP ASSEMBLY
EK100
 
220003712A 
INJECTION-PUMP ASSEMBLY
EK100
 
220201590A 
INJECTION-PUMP ASSEMBLY
EK100
 
220201592A 
INJECTION-PUMP ASSEMBLY
EK100
 
220003800A 
INJECTION-PUMP ASSEMBLY
EP100
 
220003801A 
INJECTION-PUMP ASSEMBLY
EP100
 
220003802A 
INJECTION-PUMP ASSEMBLY
EP100
 
 
INJECTION-PUMP ASSEMBLY
EP100
 
220003803A 
INJECTION-PUMP ASSEMBLY
EP100
 
220003682A 
INJECTION-PUMP ASSEMBLY
EK100
 
220003683A 
INJECTION-PUMP ASSEMBLY
EK100
 
220003684A 
INJECTION-PUMP ASSEMBLY
EK100
 
220003686A 
INJECTION-PUMP ASSEMBLY
EK100
 
220003687A 
INJECTION-PUMP ASSEMBLY
EK100
 
220201600A 
INJECTION-PUMP ASSEMBLY
EK100
 
220201602A 
INJECTION-PUMP ASSEMBLY
EK100
 
220201603A 
INJECTION-PUMP ASSEMBLY
EK100
 
220201604A 
INJECTION-PUMP ASSEMBLY
EK100
 
 
INJECTION-PUMP ASSEMBLY

Hino 

9 400 616 770 
220201605A 
INJECTION-PUMP ASSEMBLY
EK100
 
220003632A 
INJECTION-PUMP ASSEMBLY
EK100
 
220003634A 
INJECTION-PUMP ASSEMBLY
EK100
106671-3484  
9 400 610 111 
220003635A 
INJECTION-PUMP ASSEMBLY
EK100
 
 

EP100
Back to top